Natalia K. Kapustian
Natalia K. Kapustian has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Galina N. Antonovskaya
N. Laverov Federal Center for Integrated Arctic Research, Ural Branch, Russian Academy of Sciences, Arkhangelsk, Russia
11 shared publications - Aleksey V Danilov
Laverov Federal Center for Integrated Arctic Research, 163000, Arkhangelsk, Russia
2 shared publications - Eugene A. Rogozhin
Shemyakin and Ovchinnikov Institute of Bioorganic Chemistry RAS, Miklukho-Maklaya Str., 16/10, 117437 Moscow, Russia
2 shared publications - Irina Basakina
N. Laverov Federal Center for Integrated Arctic Research of the Ural Branch of the Russian Academy of Sciences
2 shared publications - Konstantin A. Moshkunov
IMCN/BSMA, Université Catholique de Louvain, 1348 Louvain-la-Neuve, Belgium
2 shared publications - Aleksey Klimov
Moscow State University of Civil Engineering
1 shared publication
Latest Publications
- Open Access
- 21 December 2022
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 17 (63) , 46-60
The earth-fill dam state express investigation using mechanical vibrations produced by HPP
The usage of mechanical vibrations produced by the hydropower plant (HPP) turbine may be used for seismic sounding of large-scale constructions as the earth-fill dam and its abutment contacts. Such vibrations are monochromatic oscillations on main frequencies and their harmonics produced by turbine. Seismic sensors installed on the dam's crest and inside it, if it possible, and in the area of abutment contacts register microseisms include HPP turbine operation vibrations which may be extracted by seismic data processing, i.e., filtering. We discuss two data processing possibilities: symphonious filter as the hardware one and power spectrum calculation as digital one. We consider the two case of earth-fill dams state investigations. There are the Chiryurt HPP dam (Republic of Dagestan, Russia, 9.5 m high) and the Nurek HPP dam (Tajikistan, 300 m high). We show the possibilities of seismic express investigations using signals of main frequencies produced by HPP turbine for dam sounding. For Chiryurt dam the extra fluid filtering in the central part of the dam was revealed. Nurek dam abutment contact monitoring showed the temporal variation of its stress-strain state associated with deformation variation 10-5-10-6 presumably due to regional seismicity.
- 21 December 2022
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 17 (63) , 46-60
Open AccessThe earth-fill dam state express investigation using mechanical vibrations produced by HPP
The usage of mechanical vibrations produced by the hydropower plant (HPP) turbine may be used for seismic sounding of large-scale constructions as the earth-fill dam and its abutment contacts. Such vibrations are monochromatic oscillations on main frequencies and their harmonics produced by turbine. Seismic sensors installed on the dam's crest and inside it, if it possible, and in the area of abutment contacts register microseisms include HPP turbine operation vibrations which may be extracted by seismic data processing, i.e., filtering. We discuss two data processing possibilities: symphonious filter as the hardware one and power spectrum calculation as digital one. We consider the two case of earth-fill dams state investigations. There are the Chiryurt HPP dam (Republic of Dagestan, Russia, 9.5 m high) and the Nurek HPP dam (Tajikistan, 300 m high). We show the possibilities of seismic express investigations using signals of main frequencies produced by HPP turbine for dam sounding. For Chiryurt dam the extra fluid filtering in the central part of the dam was revealed. Nurek dam abutment contact monitoring showed the temporal variation of its stress-strain state associated with deformation variation 10-5-10-6 presumably due to regional seismicity.
- Open Access
Soil State Testing Using Heavy Vehicle Vibrations
Changes in the elastic characteristics of the railway subgrade have been determined using nonstop long-term (more than 50 days) train passage seismic observations. We examined the records of the broadband sensitive seismometer TC-120s in the low-frequency band (below 0.1 Hz) to obtain the subgrade response to various train passages and its relaxation after unloading. Analytical models of subgrade deformation by the train are proposed. When comparing models in the experiment, we showed that a lowpass filter (below 0.1 Hz) provides waveforms with parameters determined by the deformation properties of the soil. We carried out statistical processing of 1600 train seismic records and determined parameters characterizing the subgrade reaction to the vibration effects created by trains in the ultra-low-frequency range. Therefore, we can use these parameters to monitor after daily averaging and weekly smoothing. When observing the spring thawing of the soil, we considered the sensitivity of seismic monitoring using heavy vehicle vibrations, particularly changes in the soil state properties under a rise in ambient temperature. The presented observations can be used for seismic monitoring technology at an early stage of hazardous processes in the subgrade.
Open AccessSoil State Testing Using Heavy Vehicle Vibrations
Changes in the elastic characteristics of the railway subgrade have been determined using nonstop long-term (more than 50 days) train passage seismic observations. We examined the records of the broadband sensitive seismometer TC-120s in the low-frequency band (below 0.1 Hz) to obtain the subgrade response to various train passages and its relaxation after unloading. Analytical models of subgrade deformation by the train are proposed. When comparing models in the experiment, we showed that a lowpass filter (below 0.1 Hz) provides waveforms with parameters determined by the deformation properties of the soil. We carried out statistical processing of 1600 train seismic records and determined parameters characterizing the subgrade reaction to the vibration effects created by trains in the ultra-low-frequency range. Therefore, we can use these parameters to monitor after daily averaging and weekly smoothing. When observing the spring thawing of the soil, we considered the sensitivity of seismic monitoring using heavy vehicle vibrations, particularly changes in the soil state properties under a rise in ambient temperature. The presented observations can be used for seismic monitoring technology at an early stage of hazardous processes in the subgrade.
- 16 June 2021
- Published by Seismological Society of America (SSA) in Seismological Research Letters
- Vol. 92 (5) , 2876-2890
Spatiotemporal Relationship between Arctic Mid-Ocean Ridge System and Intraplate Seismicity of the European Arctic
In this article, we investigate the influence of the Arctic mid‐ocean ridge system (AMORS), including the Gakkel and Mohns ridges, and the Knipovich ridge–Lena trough (KL) segment, on seismicity of the Novaya Zemlya archipelago area (NZ) and the northernmost margin of the East‐European Platform (EEP) for 1980–2019. For each individual area, the annual seismic energy was obtained by adding the energies of all earthquakes. To do this, we have converted various types of magnitude by different seismic networks into moment magnitude . We compiled the updated catalog for the NZ, the northern EEP, and the northern part of the Ural fold belt (UFB). As a result, we constructed time distributions of annual seismic energy releases for each composing ridges of AMORS, NZ, and EEP combined with UFB. A model based on the Elsasser’s one describing the transfer of lithospheric stress disturbances in the horizontal direction was built, and quantitative calculations of the disturbance propagations from AMORS were performed. Results are in good agreement with the annual seismic energy time lags between rifts and NZ and EEP together with the UFB. We calculated correlation coefficients between the seismic energy releases over the time for the structures, enabling identification of the characteristic excitation cycles and estimation of the interval of disturbance transfer from AMORS. As a result, disturbances from the Gakkel ridge appear 3 yr later in NZ, from the KL segment in 4 yr, and from the Mona ridge in 8 yr. For the EEP + UBF combined area, we found the following disturbances spreading lags as 7 yr for the Mona ridge, 4 yr for the KL segment, and 5 yr for the Gakkel ridge. The obtained damping amplitudes of the disturbance spreading from the arctic ridges are sufficient to affect the intraplate seismic activity.- 16 June 2021
- Published by Seismological Society of America (SSA) in Seismological Research Letters
- Vol. 92 (5) , 2876-2890
Spatiotemporal Relationship between Arctic Mid-Ocean Ridge System and Intraplate Seismicity of the European Arctic
In this article, we investigate the influence of the Arctic mid‐ocean ridge system (AMORS), including the Gakkel and Mohns ridges, and the Knipovich ridge–Lena trough (KL) segment, on seismicity of the Novaya Zemlya archipelago area (NZ) and the northernmost margin of the East‐European Platform (EEP) for 1980–2019. For each individual area, the annual seismic energy was obtained by adding the energies of all earthquakes. To do this, we have converted various types of magnitude by different seismic networks into moment magnitude . We compiled the updated catalog for the NZ, the northern EEP, and the northern part of the Ural fold belt (UFB). As a result, we constructed time distributions of annual seismic energy releases for each composing ridges of AMORS, NZ, and EEP combined with UFB. A model based on the Elsasser’s one describing the transfer of lithospheric stress disturbances in the horizontal direction was built, and quantitative calculations of the disturbance propagations from AMORS were performed. Results are in good agreement with the annual seismic energy time lags between rifts and NZ and EEP together with the UFB. We calculated correlation coefficients between the seismic energy releases over the time for the structures, enabling identification of the characteristic excitation cycles and estimation of the interval of disturbance transfer from AMORS. As a result, disturbances from the Gakkel ridge appear 3 yr later in NZ, from the KL segment in 4 yr, and from the Mona ridge in 8 yr. For the EEP + UBF combined area, we found the following disturbances spreading lags as 7 yr for the Mona ridge, 4 yr for the KL segment, and 5 yr for the Gakkel ridge. The obtained damping amplitudes of the disturbance spreading from the arctic ridges are sufficient to affect the intraplate seismic activity.- 3 January 2020
- Published by Springer Nature
- p. 127-138
New Approach of Railway Roadbed State Monitoring Using Broadband Seismometers
- 3 January 2020
- Published by Springer Nature
- p. 127-138
New Approach of Railway Roadbed State Monitoring Using Broadband Seismometers
- Open Access
- 24 December 2019
- Published by ECO-Vector LLC in Transportation systems and technology
- Vol. 5 (4) , 96-114
The broadband seismic equipment application in problems of roadbed railway smart monitoring
We present our experience of broadband seismic equipment application to detect changes of roadbed railway state in operation. Aim: to obtain experimental validation to expand the scientific basis of geophysical surveys in roadbed railway state monitoring and identifying hazardous processes at an early stage. Methods: seismic records were obtained by the authors on the Northern railway section. Seismic data were processed using a low-frequency filter of 0.5 Hz and analysis of points movement trajectories of the roadbed railway, we performed numerical modelling of the stress-strain state of the soil when specifying various physical parameters, the results were compared with the experiment. Results: We have shown experimentally and by numerical simulation that by conducting near the railway track vibrations registration formed by passing trains and analyzing the amplitudes change of these vibrations in the low-frequency band (periods of about 100 seconds), it is possible to identify potentially dangerous phenomena in the roadbed. Field observations showed changes in amplitude of oscillations during seasonal flooding; the results are consistent with modeling. The possibility of identifying the stages of freezing-thawing of the soil and associated negative processes is considered. By discussing the parameters of modern seismic equipment, the possibilities and applicability of different types of seismic sensors for roadbed railway monitoring as well as the organization of a smart monitoring system are shown. Conclusion: The possibility of using passing trains vibrations to detect changes of the roadbed railway state by analyzing the amplitudes of these vibrations is proved. Recommendations for seismic sensors choice and organization of smart roadbed state monitoring system are presented.
- 24 December 2019
- Published by ECO-Vector LLC in Transportation systems and technology
- Vol. 5 (4) , 96-114
Open AccessThe broadband seismic equipment application in problems of roadbed railway smart monitoring
We present our experience of broadband seismic equipment application to detect changes of roadbed railway state in operation. Aim: to obtain experimental validation to expand the scientific basis of geophysical surveys in roadbed railway state monitoring and identifying hazardous processes at an early stage. Methods: seismic records were obtained by the authors on the Northern railway section. Seismic data were processed using a low-frequency filter of 0.5 Hz and analysis of points movement trajectories of the roadbed railway, we performed numerical modelling of the stress-strain state of the soil when specifying various physical parameters, the results were compared with the experiment. Results: We have shown experimentally and by numerical simulation that by conducting near the railway track vibrations registration formed by passing trains and analyzing the amplitudes change of these vibrations in the low-frequency band (periods of about 100 seconds), it is possible to identify potentially dangerous phenomena in the roadbed. Field observations showed changes in amplitude of oscillations during seasonal flooding; the results are consistent with modeling. The possibility of identifying the stages of freezing-thawing of the soil and associated negative processes is considered. By discussing the parameters of modern seismic equipment, the possibilities and applicability of different types of seismic sensors for roadbed railway monitoring as well as the organization of a smart monitoring system are shown. Conclusion: The possibility of using passing trains vibrations to detect changes of the roadbed railway state by analyzing the amplitudes of these vibrations is proved. Recommendations for seismic sensors choice and organization of smart roadbed state monitoring system are presented.
- Open Access
- 23 April 2019
- Published by MDPI AG in Geosciences
- Vol. 9 (4) , 187
Hydropower Dam State and Its Foundation Soil Survey Using Industrial Seismic Oscillations
In this article, we suggest a new type of seismic source for surveying both structure state and foundation soil conditions regardless of the level of seismic noise. In our opinion, powerful industrial equipment can be treated as seismic sources. We describe the results of a survey conducted on the Song Tranh-2 hydropower dam located in Central Vietnam. After a М = 4.7 earthquake, the dam visual inspection revealed zones of the excessive durability loss: cracks and areas with an elevated infiltration of water into the dam galleries. Powerful industrial equipment generates continuous quasi-harmonic mechanical oscillations (seismic waves) that travel through layers of rocks. These seismic oscillations are recorded by receivers in different measurement points such as the dam body, abutments, and the foundation soils. Anomalous amplitudes of these oscillations indicate the presence of weakened zones in the structure or in foundation soil. We coupled passive and active seismic methods to more precisely find such zones. In this case, active seismic methods allowed us to investigate dam abutment zones, and passive seismic methods were used to localize weakened zones in the dam-foundation soil system. We assumed that the joint contribution of two factors was the cause of the dam weakening. One of them was caused by increased water infiltration through the rock mass and its contact zones, and the other was reservoir-induced seismicity contributing to the deterioration of the foundation soils, which was possibly the reason for a shift in the dam in the contact zone with the rock mass foundation. It is necessary to perform computer modelling, which was not included in our research. The developed method can be used for the safety control of the hydropower station dams.
- 23 April 2019
- Published by MDPI AG in Geosciences
- Vol. 9 (4) , 187
Open AccessHydropower Dam State and Its Foundation Soil Survey Using Industrial Seismic Oscillations
In this article, we suggest a new type of seismic source for surveying both structure state and foundation soil conditions regardless of the level of seismic noise. In our opinion, powerful industrial equipment can be treated as seismic sources. We describe the results of a survey conducted on the Song Tranh-2 hydropower dam located in Central Vietnam. After a М = 4.7 earthquake, the dam visual inspection revealed zones of the excessive durability loss: cracks and areas with an elevated infiltration of water into the dam galleries. Powerful industrial equipment generates continuous quasi-harmonic mechanical oscillations (seismic waves) that travel through layers of rocks. These seismic oscillations are recorded by receivers in different measurement points such as the dam body, abutments, and the foundation soils. Anomalous amplitudes of these oscillations indicate the presence of weakened zones in the structure or in foundation soil. We coupled passive and active seismic methods to more precisely find such zones. In this case, active seismic methods allowed us to investigate dam abutment zones, and passive seismic methods were used to localize weakened zones in the dam-foundation soil system. We assumed that the joint contribution of two factors was the cause of the dam weakening. One of them was caused by increased water infiltration through the rock mass and its contact zones, and the other was reservoir-induced seismicity contributing to the deterioration of the foundation soils, which was possibly the reason for a shift in the dam in the contact zone with the rock mass foundation. It is necessary to perform computer modelling, which was not included in our research. The developed method can be used for the safety control of the hydropower station dams.
- 1 September 2018
- Published by Allerton Press in Seismic Instruments
- Vol. 54 (5) , 531-535
A New System for Monitoring Hydraulic Engineering Structures
To ensure the safety of hydraulic engineering structures (HESs), we analyze the methods and requirements on equipment for seismological monitoring in the area of emplacement, inspecting the...
- 1 September 2018
- Published by Allerton Press in Seismic Instruments
- Vol. 54 (5) , 531-535
A New System for Monitoring Hydraulic Engineering Structures
To ensure the safety of hydraulic engineering structures (HESs), we analyze the methods and requirements on equipment for seismological monitoring in the area of emplacement, inspecting the...
- Open Access
- 15 September 2017
- Published by ECO-Vector LLC in Transportation systems and technology
- Vol. 3 (3) , 133-161
Possibilities of seismic methods for the estimation of a railway roadbed state under the conditions of the far north
The article presents results of monitoring state of railway subgrade using seismic methods in the Far North area. Purpose: The purpose of the studies is to find out reasons of subgrade subsidence in turfed soils of Onezhsky District of Arkhangelsk Oblast. Methodology: Studying soils in foundations of subgrade, a complex of active and passive methods was used, including: seismic exploration of refracted waves, multi-channel analysis of ground waves, and engineering seismic analysis based upon spectrum analysis of seismic noises. This complex enabled considering and estimating the system “subgrade-soils of foundations”. Results: A relative high capacity of weak soils, probably containing turf, lying under subgrade. Sections of increased water saturation in subgrade soils were found out. Loads from passing trains and resonant effect in weak soils cause its compression resulting in emergence of subsidence. Resonant effects whereby are not that strong, whereas passing trains have a more significant impact on the state of subgrades. Practical significance: Elaboration of technology of quick estimation of state of railway subgrade for immediate detection of a dangerous defect at an early stage of its development is a topical and acute challenge.
- 15 September 2017
- Published by ECO-Vector LLC in Transportation systems and technology
- Vol. 3 (3) , 133-161
Open AccessPossibilities of seismic methods for the estimation of a railway roadbed state under the conditions of the far north
The article presents results of monitoring state of railway subgrade using seismic methods in the Far North area. Purpose: The purpose of the studies is to find out reasons of subgrade subsidence in turfed soils of Onezhsky District of Arkhangelsk Oblast. Methodology: Studying soils in foundations of subgrade, a complex of active and passive methods was used, including: seismic exploration of refracted waves, multi-channel analysis of ground waves, and engineering seismic analysis based upon spectrum analysis of seismic noises. This complex enabled considering and estimating the system “subgrade-soils of foundations”. Results: A relative high capacity of weak soils, probably containing turf, lying under subgrade. Sections of increased water saturation in subgrade soils were found out. Loads from passing trains and resonant effect in weak soils cause its compression resulting in emergence of subsidence. Resonant effects whereby are not that strong, whereas passing trains have a more significant impact on the state of subgrades. Practical significance: Elaboration of technology of quick estimation of state of railway subgrade for immediate detection of a dangerous defect at an early stage of its development is a topical and acute challenge.
- 17 March 2017
- Published by Springer Nature in Journal of Seismology
- Vol. 21 (5) , 1039-1053
New seismic array solution for earthquake observations and hydropower plant health monitoring
- 17 March 2017
- Published by Springer Nature in Journal of Seismology
- Vol. 21 (5) , 1039-1053
New seismic array solution for earthquake observations and hydropower plant health monitoring
- 1 January 2016
- Published by Allerton Press in Seismic Instruments
- Vol. 52 (1) , 1-8
Seismic monitoring of industrial objects: Problems and solutions
- 1 January 2016
- Published by Allerton Press in Seismic Instruments
- Vol. 52 (1) , 1-8
Seismic monitoring of industrial objects: Problems and solutions