D. Berdjane
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
D. Berdjane has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Amel Gharbi
Research Center in Industrial Technologies (CRTI), P.O. Box 64 Cheraga 16014 Algiers, Algeria
2 shared publications - Chems Eddine Ramoul
Research Center in Industrial Technologies (CRTI) Cheraga Algeria
2 shared publications - Oualid Ghelloudj
Research Center in Industrial Technologies (CRTI)
2 shared publications - Toufik Chouchane
Research Center in Industrial Technologies CRTI, Algiers, Algeria
2 shared publications A. Gharbi
Research Center in Industrial Technologies (CRTI), P.O. Box 64 Cheraga 16014 Algiers, Algeria
1 shared publicationA. Himour
LMGM. Metallurgy Department, Badji-Mokhtar University BP12, 23200 Annaba, Algeria
1 shared publication
Latest Publications
- Open Access
- 1 March 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1818 (1) , 012173
Comparative Study on The Corrosion Behavior of High Strength Pipe Steel After Thermal and Thermomechanical Treatments
The corrosion behaviour of X80 steel samples rolled and other quench-tempered in 3.5% NaCl have been studied. Optical microscopy, scanning electron microscopy, potentiodynamic polarization tests and electrochemical impedance measurements are the techniques used to characterize the samples. The results show that the tempered steel has a low corrosion current density compared to the rolled steel. The impedance measurements show the presence of a single capacitive loop attributed to the load transfer phenomenon.
- 1 March 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1818 (1) , 012173
Open AccessComparative Study on The Corrosion Behavior of High Strength Pipe Steel After Thermal and Thermomechanical Treatments
The corrosion behaviour of X80 steel samples rolled and other quench-tempered in 3.5% NaCl have been studied. Optical microscopy, scanning electron microscopy, potentiodynamic polarization tests and electrochemical impedance measurements are the techniques used to characterize the samples. The results show that the tempered steel has a low corrosion current density compared to the rolled steel. The impedance measurements show the presence of a single capacitive loop attributed to the load transfer phenomenon.
- Open Access
- 1 March 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1818 (1) , 012159
Tribological behavior and microstructural characterization of austenitic stainless steel stabilized with Nb and V
This study deals with the influence of the addition of vanadium and niobium with concentrations of 1.2% and 0.14%, respectively, on the variation of the microstructure, and the tribological behavior of an AISI309 austenitic stainless steel. The studied specimens were structurally characterized by optical microscopy, scanning electron microscopy (SEM) X-ray diffraction and and differential scanning calorimetry (DSC). These samples were also subjected to a tribological study using the friction wear test. The results show that the addition of vanadium and niobium causes a precipitation of stable carbides (VC, NbC) which in mm causes a decrease of the chromium carbide precipitation rate. Tribological test results have also shown that the addition of these two elements improves the wear resistance of AISI309 austenitic stainless steel by decreasing the coefficient of friction fr om 0.824 to 0.554.
- 1 March 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1818 (1) , 012159
Open AccessTribological behavior and microstructural characterization of austenitic stainless steel stabilized with Nb and V
This study deals with the influence of the addition of vanadium and niobium with concentrations of 1.2% and 0.14%, respectively, on the variation of the microstructure, and the tribological behavior of an AISI309 austenitic stainless steel. The studied specimens were structurally characterized by optical microscopy, scanning electron microscopy (SEM) X-ray diffraction and and differential scanning calorimetry (DSC). These samples were also subjected to a tribological study using the friction wear test. The results show that the addition of vanadium and niobium causes a precipitation of stable carbides (VC, NbC) which in mm causes a decrease of the chromium carbide precipitation rate. Tribological test results have also shown that the addition of these two elements improves the wear resistance of AISI309 austenitic stainless steel by decreasing the coefficient of friction fr om 0.824 to 0.554.
- 1 March 2017
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 131 (3) , 420-422
Reliability of the High Strength Pipeline Steel under Corrosion Defect
- 1 March 2017
- Published by Institute of Physics, Polish Academy of Sciences in Acta Physica Polonica A
- Vol. 131 (3) , 420-422
Reliability of the High Strength Pipeline Steel under Corrosion Defect
- 1 January 2012
- Published by EDP Sciences in Revue de Métallurgie
- Vol. 109 (6) , 465-475
Deformation behavior of a Nb-Ti-V microalloyed steel to achieve the HSLA X80 grade by simulation with a torsion test and pilot hot rolling mill
- 1 January 2012
- Published by EDP Sciences in Revue de Métallurgie
- Vol. 109 (6) , 465-475
Deformation behavior of a Nb-Ti-V microalloyed steel to achieve the HSLA X80 grade by simulation with a torsion test and pilot hot rolling mill