I. Yu. Pyshmintsev
Research Subjects
Research Interests
I. Yu. Pyshmintsev has a total of 162 co-authors. Here are the top co-authors by number of shared publications:
A. B. Arabei
PAO Gazprom
11 shared publicationsM. A. Smirnov
OAO Russian Scientific Research Institute of the Pipe Industry
7 shared publicationsV. M. Farber
Ural Federal University
7 shared publicationsA. O. Struin
OAO Rossiinskii Nauchno-Issledovatel’skii Institute Trubnoi Promyshlennosti
6 shared publicationsS. M. Bityukov
LLC “Research Center TMK
6 shared publicationsS. Yu. Zhukova
OAO Sinarskii Trubnyi Zavod
6 shared publications
Latest Publications
- Open Access
- 6 May 2026
- Published by Elsevier in SSRN Electronic Journal
Mechanical behavior of pipeline steel after strain aging. Part II: Modeling
Based on the patterns identified in Part II for the variation of steel strength properties across different microstructural states, a phenomenological numerical model was developed to describe the mechanical behavior of pipeline steel after strain aging (SA). For estimating the increase in yield strength due to bake hardening (BH), it is proposed to use an empirical relationship that accounts for the concentration of carbon dissolved in alpha iron, as well as the aging temperature and time. The numerical simulation results were used to fit the parameters of the isotropic component of the combined hardening law in the updated Voce-Chaboche (UVC) model, which considers Lüders strain.Validation of the numerical model demonstrated a high Pearson correlation with the experimental data ([[EQUATION]] > 0.95) obtained from tensile tests on pre-strained and aged steel subjected to prior monotonic deformation. The strength parameters obtained from the model were then used to simulate 3% pipe bending strain in the ABAQUS CAE finite element software. The finite element analysis (FEA) results showed that the highest strain localization and, accordingly, the greatest risk of buckling occur in the strain-aged pipe with a microstructure produced by quenching from the austenitization temperature followed by high-temperature tempering. Owing to its greater strain-hardening stability, the normalized microstructure ensures the most uniform strain distribution at comparatively lower strength. The microstructure formed after re-quenching from the intercritical temperature range provides the most favorable combination of strength and ductility, reducing strain heterogeneity and the risk of buckling during ovalization.
- 6 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMechanical behavior of pipeline steel after strain aging. Part II: Modeling
Based on the patterns identified in Part II for the variation of steel strength properties across different microstructural states, a phenomenological numerical model was developed to describe the mechanical behavior of pipeline steel after strain aging (SA). For estimating the increase in yield strength due to bake hardening (BH), it is proposed to use an empirical relationship that accounts for the concentration of carbon dissolved in alpha iron, as well as the aging temperature and time. The numerical simulation results were used to fit the parameters of the isotropic component of the combined hardening law in the updated Voce-Chaboche (UVC) model, which considers Lüders strain.Validation of the numerical model demonstrated a high Pearson correlation with the experimental data ([[EQUATION]] > 0.95) obtained from tensile tests on pre-strained and aged steel subjected to prior monotonic deformation. The strength parameters obtained from the model were then used to simulate 3% pipe bending strain in the ABAQUS CAE finite element software. The finite element analysis (FEA) results showed that the highest strain localization and, accordingly, the greatest risk of buckling occur in the strain-aged pipe with a microstructure produced by quenching from the austenitization temperature followed by high-temperature tempering. Owing to its greater strain-hardening stability, the normalized microstructure ensures the most uniform strain distribution at comparatively lower strength. The microstructure formed after re-quenching from the intercritical temperature range provides the most favorable combination of strength and ductility, reducing strain heterogeneity and the risk of buckling during ovalization.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Металлы / Russian Metallurgy
- No. 6,p. 69-79
Effect of Microstructural and Crystallographic Texture Parameters on the Fracture Energy Absorption of X90 Pipeline Steel
The microstructure, substructure, and crystallographic texture of X90 pipeline steel were studied using optical and electron microscopy, electron backscatter diffraction (EBSD), and X-ray texture analysis. Fracture energy absorption was measured by drop-weight tear testing. The preferred grains orientation and substructure characteristics within lath bainite bands were analyzed. A comparative assessment was carried out for misorientation angles, the extent of low-angle grain boundaries, lattice distortions, and microhardness within and between lath bainite bands. Correlations between fracture energy absorption in drop-weight tear tests and both the fraction of bainitic bands and specific texture parameters, such as the volume fraction of grains with the {001} component and the volume fraction of grains with the || TD orientation were established.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Металлы / Russian Metallurgy
- No. 6,p. 69-79
Effect of Microstructural and Crystallographic Texture Parameters on the Fracture Energy Absorption of X90 Pipeline Steel
The microstructure, substructure, and crystallographic texture of X90 pipeline steel were studied using optical and electron microscopy, electron backscatter diffraction (EBSD), and X-ray texture analysis. Fracture energy absorption was measured by drop-weight tear testing. The preferred grains orientation and substructure characteristics within lath bainite bands were analyzed. A comparative assessment was carried out for misorientation angles, the extent of low-angle grain boundaries, lattice distortions, and microhardness within and between lath bainite bands. Correlations between fracture energy absorption in drop-weight tear tests and both the fraction of bainitic bands and specific texture parameters, such as the volume fraction of grains with the {001} component and the volume fraction of grains with the || TD orientation were established.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Металлы / Russian Metallurgy
- No. 6,p. 80-89
The Influence of the Structural State of 09G2S Steel on Mechanical Properties over a Wide Temperature Range
The influence of the structural state of the wall material of a seamless pipe made of 09G2C steel, after heat treatment under various regimes, on its mechanical properties was studied during uniaxial tensile testing in the temperature range of 20 to 400 °C and during impact bending testing in the range of 0 to –70 °C. It was shown that a bimodal banded structure of ferrite and tempered bainite, formed after quenching from the two-phase region and high tempering near the Ac temperature, exhibits a greater tendency toward both static and dynamic strain aging compared to the homogeneous structure of tempered bainite obtained by quenching from a temperature above Ac followed by high tempering. This effect is attributed to the increased carbon concentration in the solid solution and the small size of structural elements within the tempered bainite bands. Additionally, the impact strength of the pipe wall material with a homogeneous structure decreases as the test temperature drops below –40 °C, whereas the impact strength of the material with a bimodal banded structure remains stable down to –70 °C, which is attributed to its layered morphology.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Металлы / Russian Metallurgy
- No. 6,p. 80-89
The Influence of the Structural State of 09G2S Steel on Mechanical Properties over a Wide Temperature Range
The influence of the structural state of the wall material of a seamless pipe made of 09G2C steel, after heat treatment under various regimes, on its mechanical properties was studied during uniaxial tensile testing in the temperature range of 20 to 400 °C and during impact bending testing in the range of 0 to –70 °C. It was shown that a bimodal banded structure of ferrite and tempered bainite, formed after quenching from the two-phase region and high tempering near the Ac temperature, exhibits a greater tendency toward both static and dynamic strain aging compared to the homogeneous structure of tempered bainite obtained by quenching from a temperature above Ac followed by high tempering. This effect is attributed to the increased carbon concentration in the solid solution and the small size of structural elements within the tempered bainite bands. Additionally, the impact strength of the pipe wall material with a homogeneous structure decreases as the test temperature drops below –40 °C, whereas the impact strength of the material with a bimodal banded structure remains stable down to –70 °C, which is attributed to its layered morphology.
- Open Access
- 11 November 2023
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 66 (5) , 571-579
Effect of retained austenite on mechanical properties of steel with 15 % Cr
The paper considers the study of influence of retained austenite on the mechanical properties of steel of the austenite-martensitic class based on 15 % Cr after various heat treatment. Significant amount of retained austenite remains in the steel microstructure after quenching and subsequent tempering or heating in the intercritical temperature range that makes difficult to achieve a high yield strength. Destabilization of retained austenite with subsequent transformation into newly formed martensite is provided by multi-stage heat treatment which includes quenching, heating in the intercritical temperature range or above the AC3 point and final tempering. It was established that retained austenite remains in the microstructure of two-phase steel and has the form of blocks and thin layers located in the inter-lath space. Tensile testing of steel based on 15 % Cr showed that multi-stage heat treatment provides a high-strength condition corresponding to strength groups Q125 and Q135. A comparative analysis of deformation behavior of semi-austenitic steel in various states indicates that the beginning of the martensitic transformation after the final tempering shifts into the elastic region during tension and leads to the formation of stress-assisted martensite. It was determined that block-shaped retained austenite in steel with 15 % Cr predominantly undergoes martensitic transformation during tensile and impact tests at a subzero temperature. This is supposed to be the reason for the noticeably lower impact toughness of semi-austenitic steel with 15 % Cr compared to martensitic steel with 13 % Cr at equal strength.
- 11 November 2023
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 66 (5) , 571-579
Open AccessEffect of retained austenite on mechanical properties of steel with 15 % Cr
The paper considers the study of influence of retained austenite on the mechanical properties of steel of the austenite-martensitic class based on 15 % Cr after various heat treatment. Significant amount of retained austenite remains in the steel microstructure after quenching and subsequent tempering or heating in the intercritical temperature range that makes difficult to achieve a high yield strength. Destabilization of retained austenite with subsequent transformation into newly formed martensite is provided by multi-stage heat treatment which includes quenching, heating in the intercritical temperature range or above the AC3 point and final tempering. It was established that retained austenite remains in the microstructure of two-phase steel and has the form of blocks and thin layers located in the inter-lath space. Tensile testing of steel based on 15 % Cr showed that multi-stage heat treatment provides a high-strength condition corresponding to strength groups Q125 and Q135. A comparative analysis of deformation behavior of semi-austenitic steel in various states indicates that the beginning of the martensitic transformation after the final tempering shifts into the elastic region during tension and leads to the formation of stress-assisted martensite. It was determined that block-shaped retained austenite in steel with 15 % Cr predominantly undergoes martensitic transformation during tensile and impact tests at a subzero temperature. This is supposed to be the reason for the noticeably lower impact toughness of semi-austenitic steel with 15 % Cr compared to martensitic steel with 13 % Cr at equal strength.
- 27 May 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (1-2) , 137-147
Electrochemical Investigation of the Corrosion Resistance of Metal for Oil and Gas Pipelines
- 27 May 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (1-2) , 137-147
Electrochemical Investigation of the Corrosion Resistance of Metal for Oil and Gas Pipelines
- 1 January 2023
- Published by Springer Nature in Metallurgist
- Vol. 66 (9-10) , 1173-1180
Structure and Properties of Steel for Producing Hydrogen Sulfide Resistant Oil and Gas High Strength Pipes
- 1 January 2023
- Published by Springer Nature in Metallurgist
- Vol. 66 (9-10) , 1173-1180
Structure and Properties of Steel for Producing Hydrogen Sulfide Resistant Oil and Gas High Strength Pipes
- 1 January 2023
- Published by Springer Nature in Metallurgist
- Vol. 66 (9-10) , 1068-1075
Effect of Hydrogen Sulfide on Pipe Steel Carbon Dioxide Corrosion
- 1 January 2023
- Published by Springer Nature in Metallurgist
- Vol. 66 (9-10) , 1068-1075
Effect of Hydrogen Sulfide on Pipe Steel Carbon Dioxide Corrosion
- 1 November 2022
- Published by Allerton Press in Steel in Translation
- Vol. 52 (11) , 1079-1085
Local Chromium Plating as a Promising Method for Refurbishing Long Retained Mandrels in Continuous Rolling Mills
Technology and equipment based on local chromium plating have been developed for local repairing surfaces with defects on long chromium-plated mandrels of
- 1 November 2022
- Published by Allerton Press in Steel in Translation
- Vol. 52 (11) , 1079-1085
Local Chromium Plating as a Promising Method for Refurbishing Long Retained Mandrels in Continuous Rolling Mills
Technology and equipment based on local chromium plating have been developed for local repairing surfaces with defects on long chromium-plated mandrels of
- Open Access
- 2 October 2022
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 65 (9) , 644-653
Features of microstructure, phase composition and strengthening capability of stainless steels with 13 – 17 % Cr
The paper considers the study of the features of structure and phase transformations in high-strength, resistant to carbon dioxide corrosion, complex alloyed steels of martensitic, austenitic-martensitic and martensitic-ferritic classes with 13 – 17 % Cr. Influence of the alloying on crystallization and solid state phase transformations was revealed in the temperature range of hot deformation and heat treatment using thermodynamic modeling and experimental study. The effect of quenching temperature on the phase composition and microstructure was analyzed as a result of X-ray diffraction phase analysis, optical and transmission electron microscopy. It was found that increase of nickel content leads to growth of retained austenite fraction resulting in significant decrease of yield strength along with high tensile strength and elongation. To obtain predominantly martensitic microstructure in martensitic-austenitic steel, the multistage heat treatment is proposed including quenching, intermediate annealing for precipitation of dispersed carbides and tempering forming final mechanical properties. The composition of precipitated carbides was evaluated by X-ray microanalysis. The results of the tensile test for steels with martensitic and martensitic-ferritic microstructure showed that required strength grade (σ0.65 ≥ 862 MPa; σв ≥ 931 MPa) was reached after heat treatment including quenching and tempering. Multistage heat treatment including quenching, intermediate annealing and final tempering was resulted in required strength properties of high-nickel martensitic-austenitic steel with 15 % Cr.
- 2 October 2022
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 65 (9) , 644-653
Open AccessFeatures of microstructure, phase composition and strengthening capability of stainless steels with 13 – 17 % Cr
The paper considers the study of the features of structure and phase transformations in high-strength, resistant to carbon dioxide corrosion, complex alloyed steels of martensitic, austenitic-martensitic and martensitic-ferritic classes with 13 – 17 % Cr. Influence of the alloying on crystallization and solid state phase transformations was revealed in the temperature range of hot deformation and heat treatment using thermodynamic modeling and experimental study. The effect of quenching temperature on the phase composition and microstructure was analyzed as a result of X-ray diffraction phase analysis, optical and transmission electron microscopy. It was found that increase of nickel content leads to growth of retained austenite fraction resulting in significant decrease of yield strength along with high tensile strength and elongation. To obtain predominantly martensitic microstructure in martensitic-austenitic steel, the multistage heat treatment is proposed including quenching, intermediate annealing for precipitation of dispersed carbides and tempering forming final mechanical properties. The composition of precipitated carbides was evaluated by X-ray microanalysis. The results of the tensile test for steels with martensitic and martensitic-ferritic microstructure showed that required strength grade (σ0.65 ≥ 862 MPa; σв ≥ 931 MPa) was reached after heat treatment including quenching and tempering. Multistage heat treatment including quenching, intermediate annealing and final tempering was resulted in required strength properties of high-nickel martensitic-austenitic steel with 15 % Cr.
- 1 September 2022
- Published by Allerton Press in Steel in Translation
- Vol. 52 (9) , 844-851
Features of Microstructure, Phase Composition and Strengthening Capability of Stainless Steels with Chromium Content of 13–17%
The paper studies features of structural and phase transformations of complex alloyed high-strength martensitic, austenitic-martensitic and martensitic-fer
- 1 September 2022
- Published by Allerton Press in Steel in Translation
- Vol. 52 (9) , 844-851
Features of Microstructure, Phase Composition and Strengthening Capability of Stainless Steels with Chromium Content of 13–17%
The paper studies features of structural and phase transformations of complex alloyed high-strength martensitic, austenitic-martensitic and martensitic-fer