Saša R. Gocić
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Saša R. Gocić has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Suzana N. Stamenković
Department of Physics, Faculty of Sciences and Mathematics, University of Niš, PO Box 224, 18001 Niš, Serbia
12 shared publications V. Lj. Marković
University of Niš Department of Physics P.O. Box 224, 18001 Niš, Serbia
6 shared publications- Zoran Lj Petrovic
Serbian Academy of Sciences and Arts, Belgrade, Serbia
6 shared publications V Lj Marković
3 shared publications- Aleksandar P. Jovanovic
Leibniz Institute for Plasma Science and Technology (INP), Felix-Hausdorff-Str. 2, 17489 Greifswald, Germany
2 shared publications - Branka Radovanovic
Faculty of Mechanical Engineering, University of Nis
2 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by National Library of Serbia in Thermal Science
- No. 00,p. 162
Investigating the impact of aluminum heat sinks on passive cooling of photovoltaic panels
As the temperature of photovoltaic panels rises, a drop in electrical conversion efficiency and output power is unavoidable. Therefore, a simple and low-cost cooling solution is needed - one that requires little or no maintenance and consumes no electricity. In this paper, we experimentally and numerically investigated passive cooling of photovoltaic panels using heat sinks of different geometries. Our experiments showed that these heat sinks reduce the average back-side temperature of the cooled panel by 13.6°C compared to a reference panel. They also increased the open-circuit voltage by 0.27 V relative to the reference. We also performed numerical simulations using Ansys Fluent 2025 R2. The simulated temperatures agreed well with the experimental data - the average difference was less than 1°C (approximately 1.9% relative difference). The simulations gave us a good insight into heat dissipation from the heat sinks. They revealed better cooling due to proper fin spacing, but also a limitation caused by the small contact area between the heat sink and the photovoltaic panel. These results confirm that passive cooling with aluminum heat sinks is a good method for improving photovoltaic panel performance, while the developed numerical model represents an accurate tool for heat sink design optimization.
- 1 January 2026
- Published by National Library of Serbia in Thermal Science
- No. 00,p. 162
Open AccessInvestigating the impact of aluminum heat sinks on passive cooling of photovoltaic panels
As the temperature of photovoltaic panels rises, a drop in electrical conversion efficiency and output power is unavoidable. Therefore, a simple and low-cost cooling solution is needed - one that requires little or no maintenance and consumes no electricity. In this paper, we experimentally and numerically investigated passive cooling of photovoltaic panels using heat sinks of different geometries. Our experiments showed that these heat sinks reduce the average back-side temperature of the cooled panel by 13.6°C compared to a reference panel. They also increased the open-circuit voltage by 0.27 V relative to the reference. We also performed numerical simulations using Ansys Fluent 2025 R2. The simulated temperatures agreed well with the experimental data - the average difference was less than 1°C (approximately 1.9% relative difference). The simulations gave us a good insight into heat dissipation from the heat sinks. They revealed better cooling due to proper fin spacing, but also a limitation caused by the small contact area between the heat sink and the photovoltaic panel. These results confirm that passive cooling with aluminum heat sinks is a good method for improving photovoltaic panel performance, while the developed numerical model represents an accurate tool for heat sink design optimization.
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Thermal Science
- Vol. 29 (5 Part A) , 3401-3414
Enhancement of photovoltaic panel’s power using closed back side cooling system and numerical simulation
The efficiency of PV panels is significantly influenced by the temperature of the cells, as higher temperatures reduce electrical power output, degrade performance, and shorten the panel?s lifespan. This study investigates the effectiveness of a closed-loop cooling system applied to the backside of a PV panel to enhance its output characteristics. The cooling system circulated approximately 20 L of water at a constant flow rate of 70 Lph. The results demonstrated a substantial 41.75% increase in power output, with the maximum efficiency achieved at peak cooling. Using real weather data recorded during the experiment, the temperature distribution across the panel layers was modeled using the ANSYS FLUENT 2023 R1 software package. The simulation and experimental results showed a maximum temperature difference of 1.6?C between the measured and simulated values. The cooled panel maintained an average temperature of 26.65?C, with a minimum of 16.7?C, compared to an uncooled panel?s higher temperatures. The system effectively reduced the temperature of the front side of the panel by up to 23.1?C, enhancing the overall energy output. These findings confirm that cooling PV panels from the back is an efficient method to reduce temperature and increase panel efficiency. Detailed simulations and analyses enable insight into PVT system performance and forecasting of production under various climatic conditions.
- 1 January 2025
- Published by National Library of Serbia in Thermal Science
- Vol. 29 (5 Part A) , 3401-3414
Open AccessEnhancement of photovoltaic panel’s power using closed back side cooling system and numerical simulation
The efficiency of PV panels is significantly influenced by the temperature of the cells, as higher temperatures reduce electrical power output, degrade performance, and shorten the panel?s lifespan. This study investigates the effectiveness of a closed-loop cooling system applied to the backside of a PV panel to enhance its output characteristics. The cooling system circulated approximately 20 L of water at a constant flow rate of 70 Lph. The results demonstrated a substantial 41.75% increase in power output, with the maximum efficiency achieved at peak cooling. Using real weather data recorded during the experiment, the temperature distribution across the panel layers was modeled using the ANSYS FLUENT 2023 R1 software package. The simulation and experimental results showed a maximum temperature difference of 1.6?C between the measured and simulated values. The cooled panel maintained an average temperature of 26.65?C, with a minimum of 16.7?C, compared to an uncooled panel?s higher temperatures. The system effectively reduced the temperature of the front side of the panel by up to 23.1?C, enhancing the overall energy output. These findings confirm that cooling PV panels from the back is an efficient method to reduce temperature and increase panel efficiency. Detailed simulations and analyses enable insight into PVT system performance and forecasting of production under various climatic conditions.
- 1 October 2022
- Published by AIP Publishing in Physics of Plasmas
- Vol. 29 (10) , 103504
Influence of air and water vapor on EEDF, plasma parameters, and the main RONS in atmospheric pressure low temperature helium plasmas: Global model approach
A zero-dimensional global model is developed with an aim to study the influence of air and water vapor on an electron energy distribution function, electron density, and temperature as well as on the chemical composition of atmospheric pressure helium plasmas, with special focus on the main reactive oxygen and nitrogen species important for applications of low temperature plasmas. The main channels for the production and consumption of electrons and electron energy gain and loss are examined by a global model based on a parametric study with variations of the mole fractions of air and water vapor. The calculations are done for 100, 1000, and 10 000 ppm of air in plasma, and for each of these values, the content of water vapor is taken to be 100, 1000, 2000, …, to 10 000 ppm. The variations of the most important production and consumption processes for reactive oxygen and nitrogen species are analyzed in detail. According to the results presented in this paper, water vapor highly contributes to electronegativity of the plasma through pronounced attachment of electrons, which then leads to an increase in electron temperature. For high water vapor content, vibrational excitations of water molecules are one of the main electron energy loss processes, leading to a further effect on the plasma composition. Water decreases concentrations of atomic oxygen, nitrogen, and ozone, while there is an increase in nitrogen oxide, OH, H2O2, and HO2 concentrations. Cross-sectional data for electron scattering on ground and excited state neutrals are mainly taken from the Quantemol-DB database.
- 1 October 2022
- Published by AIP Publishing in Physics of Plasmas
- Vol. 29 (10) , 103504
Influence of air and water vapor on EEDF, plasma parameters, and the main RONS in atmospheric pressure low temperature helium plasmas: Global model approach
A zero-dimensional global model is developed with an aim to study the influence of air and water vapor on an electron energy distribution function, electron density, and temperature as well as on the chemical composition of atmospheric pressure helium plasmas, with special focus on the main reactive oxygen and nitrogen species important for applications of low temperature plasmas. The main channels for the production and consumption of electrons and electron energy gain and loss are examined by a global model based on a parametric study with variations of the mole fractions of air and water vapor. The calculations are done for 100, 1000, and 10 000 ppm of air in plasma, and for each of these values, the content of water vapor is taken to be 100, 1000, 2000, …, to 10 000 ppm. The variations of the most important production and consumption processes for reactive oxygen and nitrogen species are analyzed in detail. According to the results presented in this paper, water vapor highly contributes to electronegativity of the plasma through pronounced attachment of electrons, which then leads to an increase in electron temperature. For high water vapor content, vibrational excitations of water molecules are one of the main electron energy loss processes, leading to a further effect on the plasma composition. Water decreases concentrations of atomic oxygen, nitrogen, and ozone, while there is an increase in nitrogen oxide, OH, H2O2, and HO2 concentrations. Cross-sectional data for electron scattering on ground and excited state neutrals are mainly taken from the Quantemol-DB database.
- 30 August 2018
- Published by Springer Nature in The European Physical Journal Plus
- Vol. 133 (8) , 344
Influence of space charge density on electron energy distribution function and on composition of atmospheric pressure He/O2/air plasmas
- 30 August 2018
- Published by Springer Nature in The European Physical Journal Plus
- Vol. 133 (8) , 344
Influence of space charge density on electron energy distribution function and on composition of atmospheric pressure He/O2/air plasmas
- Open Access
- 9 July 2018
- Published by Walter de Gruyter GmbH in Open Physics
- Vol. 16 (1) , 375-382
Global model simulation of OH production in pulsed-DC atmospheric pressure helium-air plasma jets
The results of global model simulation of an atmospheric pressure pulsed-DC helium plasma jet propagated in humid air, compared to the results of fluid model, are presented in this paper. The primary tasks of presented simulation were determination of the density and the main production pathways of OH radicals. The calculation reveals that global model gives higher OH densities than fluid model, especially at higher electron temperatures. This overestimation is mainly caused by the intrinsic assumptions of the global model, which impose limitations on its application for modelling of very transient physical processes such are streamers or plasma bullets. The main OH production and loss processes are well recognized by global model, and additional mechanisms are involved with respect to the case of fluid modelling. According to the presented results, global model will give satisfactory assessment of OH density and overall chemical composition of modelled plasmas, if the air fraction, electron density and temperature are correctly determined.
- 9 July 2018
- Published by Walter de Gruyter GmbH in Open Physics
- Vol. 16 (1) , 375-382
Open AccessGlobal model simulation of OH production in pulsed-DC atmospheric pressure helium-air plasma jets
The results of global model simulation of an atmospheric pressure pulsed-DC helium plasma jet propagated in humid air, compared to the results of fluid model, are presented in this paper. The primary tasks of presented simulation were determination of the density and the main production pathways of OH radicals. The calculation reveals that global model gives higher OH densities than fluid model, especially at higher electron temperatures. This overestimation is mainly caused by the intrinsic assumptions of the global model, which impose limitations on its application for modelling of very transient physical processes such are streamers or plasma bullets. The main OH production and loss processes are well recognized by global model, and additional mechanisms are involved with respect to the case of fluid modelling. According to the presented results, global model will give satisfactory assessment of OH density and overall chemical composition of modelled plasmas, if the air fraction, electron density and temperature are correctly determined.
- 15 November 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 110 (10) , 103304
Multi-component non-stationary exponential distributions of the breakdown voltages and time delays in neon ramp breakdown experiments
The concept of physically based distributions used in studies concerning gas electrical breakdowns is introduced in this paper. The non-stationary exponential distribution of the breakdown voltages and time delays with time dependent distribution parameter is theoretically derived based on physical grounds starting from a binomial distribution for electron occurrence in the interelectrode gap. The experimental distributions of breakdown voltages and time delays are obtained by applying linearly rising (ramp) voltage pulses to the discharge tube with a hard galvanic layer of gold on the cathode and modeled by multi-component non-stationary exponential distribution, as well as by a Weibull distribution for the sake of comparison. In order to fit the experimental data, the multi-component voltage/time dependent distribution parameter is introduced, where is electron yield (number of generated electrons in the interelectrode gap per second), and is breakdown probability (the probability of one electron to cause a breakdown). It is shown that multi-component non-stationary exponential distribution is suitable for modeling of the experimental data when time varying voltage pulses are applied to the discharge tube.- 15 November 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 110 (10) , 103304
Multi-component non-stationary exponential distributions of the breakdown voltages and time delays in neon ramp breakdown experiments
The concept of physically based distributions used in studies concerning gas electrical breakdowns is introduced in this paper. The non-stationary exponential distribution of the breakdown voltages and time delays with time dependent distribution parameter is theoretically derived based on physical grounds starting from a binomial distribution for electron occurrence in the interelectrode gap. The experimental distributions of breakdown voltages and time delays are obtained by applying linearly rising (ramp) voltage pulses to the discharge tube with a hard galvanic layer of gold on the cathode and modeled by multi-component non-stationary exponential distribution, as well as by a Weibull distribution for the sake of comparison. In order to fit the experimental data, the multi-component voltage/time dependent distribution parameter is introduced, where is electron yield (number of generated electrons in the interelectrode gap per second), and is breakdown probability (the probability of one electron to cause a breakdown). It is shown that multi-component non-stationary exponential distribution is suitable for modeling of the experimental data when time varying voltage pulses are applied to the discharge tube.- 8 February 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 96 (6)
Breakdown probability of neon under the influence of field electron emission and surface charges on the cathode surface
Improved relations are suggested to determine of the breakdown probability in neon under the influence of field electron emission and surface charges on the gold plated cathode surfaces. The influence of field electron emission from a vacuum deposited gold layer is confirmed by the Fowler–Nordheim plot based on an analysis of the breakdown time delay dependence on the voltage . Surface regions with a reduced conductivity on a hard galvanic layer of gold caused by diffusion of nickel atoms from a nickel sublayer are confirmed by scanning electron microscopy and energy dispersive x-ray spectrum.- 8 February 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 96 (6)
Breakdown probability of neon under the influence of field electron emission and surface charges on the cathode surface
Improved relations are suggested to determine of the breakdown probability in neon under the influence of field electron emission and surface charges on the gold plated cathode surfaces. The influence of field electron emission from a vacuum deposited gold layer is confirmed by the Fowler–Nordheim plot based on an analysis of the breakdown time delay dependence on the voltage . Surface regions with a reduced conductivity on a hard galvanic layer of gold caused by diffusion of nickel atoms from a nickel sublayer are confirmed by scanning electron microscopy and energy dispersive x-ray spectrum.- 7 October 2009
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 42 (21)
Determination of correlation coefficient of the statistical and formative time delay in nitrogen
- 7 October 2009
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 42 (21)
Determination of correlation coefficient of the statistical and formative time delay in nitrogen
- 12 December 2008
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 42 (1)
Fluctuations and correlations of the formative and statistical time delay in neon
- 12 December 2008
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 42 (1)
Fluctuations and correlations of the formative and statistical time delay in neon