Cheng Luo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Cheng Luo has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Huixian Zhang
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
4 shared publications Kunlun Zhang
School of Electrical Engineering Southwest Jiaotong University Chengdu China
3 shared publications- Kunlun Zhang
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
2 shared publications - Yongzhi Jing
Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Chengdu, China
2 shared publications - Da Liang
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
1 shared publication - Guangtong Ma
Southwest Jiaotong University
1 shared publication
Latest Publications
- 28 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (1) , 1-11
Three-Dimensional Analytical Modeling of Plate-Type Superconducting Electrodynamic Suspension for Electromagnetic Launch Application
Electrodynamic suspension (EDS) has a broad application prospect in high-speed magnetic levitation transportation due to its advantages, such as strong self-stabilization ability and simple control. However, in high-speed application scenarios, flat-plate permanent magnet electric suspension has a high magnetic drag force and requires a large amount of weight of the installed permanent magnets. To ameliorate these problems, this article addresses the plate-type superconducting EDS system with a higher lift-to-drag ratio. First, the structure and principles of the superconducting EDS system are presented. Second, a 3-D analytical model of the electromagnetic force considering the transverse end effect is established by the magnetic vector potential equation and the boundary conditions at the end of the conductor plate. Among them, the source magnetic field of the superconducting magnet array required by the boundary conditions is solved by the coil discretization idea. Then, the reliability of the proposed analytical model is verified by comparing the computational results of the analytical model with the finite element simulation results. Finally, based on the 3-D analytical model, the suspension stiffness characteristics of the superconducting EDS system and the influence of specific parameters on the system's suspension performance are analyzed.
- 28 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (1) , 1-11
Three-Dimensional Analytical Modeling of Plate-Type Superconducting Electrodynamic Suspension for Electromagnetic Launch Application
Electrodynamic suspension (EDS) has a broad application prospect in high-speed magnetic levitation transportation due to its advantages, such as strong self-stabilization ability and simple control. However, in high-speed application scenarios, flat-plate permanent magnet electric suspension has a high magnetic drag force and requires a large amount of weight of the installed permanent magnets. To ameliorate these problems, this article addresses the plate-type superconducting EDS system with a higher lift-to-drag ratio. First, the structure and principles of the superconducting EDS system are presented. Second, a 3-D analytical model of the electromagnetic force considering the transverse end effect is established by the magnetic vector potential equation and the boundary conditions at the end of the conductor plate. Among them, the source magnetic field of the superconducting magnet array required by the boundary conditions is solved by the coil discretization idea. Then, the reliability of the proposed analytical model is verified by comparing the computational results of the analytical model with the finite element simulation results. Finally, based on the 3-D analytical model, the suspension stiffness characteristics of the superconducting EDS system and the influence of specific parameters on the system's suspension performance are analyzed.
- 29 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. PP (00189456) , 1
YOLOv11s-CD: An Improved YOLOv11s Method for Catenary Dropper Fault Detection
The catenary dropper (CD) fault detection is an important technical means to ensure the train current collection quality and operational safety. The existing YOLO detection algorithms need improvement in terms of accuracy, especially in the detection of small objects. To address the problem, this article proposes a catenary dropper fault detection model based on improved YOLOv11s, named YOLOv11s-CD. First, a four detection head structure DASFFHead is designed to achieve multi-scale feature fusion, by integrating an small object detection layer into the neck network and combining a dynamic adaptive spatial feature fusion module DASFF. Subsequently, the SEAM attention mechanism is embedded in the neck network layer to extract more small objects features in occluded areas. Additionally, combining the Inner-IoU and CIoU method, the InnerCIoU loss function is designed to enhance the small object detection ability. Finally, The effectiveness and accuracy of the proposed model is validated on the dataset, which is processed by the optimized contrast limited adaptive histogram equalization (CLAHE) algorithm to enhance the contrast and clarity of the small object defects. Experimental results show that the proposed YOLOv11s-CD has superior performance compared with several other YOLO algorithms, whose mAP@0.5 has increased to 92.3% and AP of small object detection has significantly increased to 91.3%.
- 29 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. PP (00189456) , 1
YOLOv11s-CD: An Improved YOLOv11s Method for Catenary Dropper Fault Detection
The catenary dropper (CD) fault detection is an important technical means to ensure the train current collection quality and operational safety. The existing YOLO detection algorithms need improvement in terms of accuracy, especially in the detection of small objects. To address the problem, this article proposes a catenary dropper fault detection model based on improved YOLOv11s, named YOLOv11s-CD. First, a four detection head structure DASFFHead is designed to achieve multi-scale feature fusion, by integrating an small object detection layer into the neck network and combining a dynamic adaptive spatial feature fusion module DASFF. Subsequently, the SEAM attention mechanism is embedded in the neck network layer to extract more small objects features in occluded areas. Additionally, combining the Inner-IoU and CIoU method, the InnerCIoU loss function is designed to enhance the small object detection ability. Finally, The effectiveness and accuracy of the proposed model is validated on the dataset, which is processed by the optimized contrast limited adaptive histogram equalization (CLAHE) algorithm to enhance the contrast and clarity of the small object defects. Experimental results show that the proposed YOLOv11s-CD has superior performance compared with several other YOLO algorithms, whose mAP@0.5 has increased to 92.3% and AP of small object detection has significantly increased to 91.3%.
- Open Access
- 3 September 2024
- Published by Institution of Engineering and Technology (IET) in IET Electric Power Applications
- Vol. 18 (10) , 1382-1391
Effect of end leakage inductance on the performance of toroidal winding double‐sided linear induction motors
The end leakage inductance is an important component in the primary leakage inductance of the equivalent circuit. In order to calculate the end leakage inductance of a toroidal winding double‐sided linear induction motor (TW‐DSLIM) accurately and quickly, the role of ferromagnetic medium is equated by the method of images, the magnetic flux density in the end space is calculated according to the current density of the rectangular coil, end leakage inductance is obtained by calculating the end leakage magnetic energy, the impact of end leakage inductance on the performance of TW‐DSLIM is investigated, and finally the TW‐DSLIM model is established in finite element analysis to verify the effectiveness of the analytical method.
- 3 September 2024
- Published by Institution of Engineering and Technology (IET) in IET Electric Power Applications
- Vol. 18 (10) , 1382-1391
Open AccessEffect of end leakage inductance on the performance of toroidal winding double‐sided linear induction motors
The end leakage inductance is an important component in the primary leakage inductance of the equivalent circuit. In order to calculate the end leakage inductance of a toroidal winding double‐sided linear induction motor (TW‐DSLIM) accurately and quickly, the role of ferromagnetic medium is equated by the method of images, the magnetic flux density in the end space is calculated according to the current density of the rectangular coil, end leakage inductance is obtained by calculating the end leakage magnetic energy, the impact of end leakage inductance on the performance of TW‐DSLIM is investigated, and finally the TW‐DSLIM model is established in finite element analysis to verify the effectiveness of the analytical method.
- Open Access
- 10 June 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (14) , 1728-1735
Electromagnetic field coupled circuits and open‐loop control of fast starting processes in induction motors
To solve the problems of difficulty in speed measurement and low accuracy of speed measurement of induction motor (IM) during fast starting, the electromagnetic field coupling circuit (EFCC) and open‐loop control of IM considering rapid speed change are proposed. First, the EFCC of IM is established through the stator circuit, air gap magnetic field circuit and rotor circuit, and the stator voltage and electromagnetic torque of the fast starting process are deduced from the air gap magnetic density on the basis of constant slip angular velocity, and then the open‐loop control method based on the EFCC is given. Finally, compared with the open‐loop control based on the TEC, the results of simulation and experiment show that the open‐loop control based on the EFCC can follow the acceleration starting more quickly and the starting current is smaller, which is conducive to reducing the cost of the drive.
- 10 June 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (14) , 1728-1735
Open AccessElectromagnetic field coupled circuits and open‐loop control of fast starting processes in induction motors
To solve the problems of difficulty in speed measurement and low accuracy of speed measurement of induction motor (IM) during fast starting, the electromagnetic field coupling circuit (EFCC) and open‐loop control of IM considering rapid speed change are proposed. First, the EFCC of IM is established through the stator circuit, air gap magnetic field circuit and rotor circuit, and the stator voltage and electromagnetic torque of the fast starting process are deduced from the air gap magnetic density on the basis of constant slip angular velocity, and then the open‐loop control method based on the EFCC is given. Finally, compared with the open‐loop control based on the TEC, the results of simulation and experiment show that the open‐loop control based on the EFCC can follow the acceleration starting more quickly and the starting current is smaller, which is conducive to reducing the cost of the drive.
- Open Access
- 20 September 2023
- Published by Institution of Engineering and Technology (IET) in IET Electric Power Applications
- Vol. 18 (1) , 107-115
Effect of the passive damping plate on the vertical stability of permanent magnet electrodynamic suspension system
The vertical stability of permanent magnet (PM) electrodynamic suspension (EDS) system with a passive damping plate is studied because of the well‐known under‐damped nature of the EDS suspension system. The passive damping plate is installed under the Halbach permanent magnet array. When the vehicle‐mounted Halbach array and passive damping plate move to cut the track conductive plate, the 2D eddy current force is derived by establishing equations of magnetic vector potentials and using the Maxwell stress tensor method. And a 2D finite‐element model (FEM) is built to validate the accuracy of the derived levitation force equation. Based on the derived levitation force equation, the vertical stability of the PM EDS system with a passive damping plate and the effects of the main parameters on the damping ratio are analysed.
- 20 September 2023
- Published by Institution of Engineering and Technology (IET) in IET Electric Power Applications
- Vol. 18 (1) , 107-115
Open AccessEffect of the passive damping plate on the vertical stability of permanent magnet electrodynamic suspension system
The vertical stability of permanent magnet (PM) electrodynamic suspension (EDS) system with a passive damping plate is studied because of the well‐known under‐damped nature of the EDS suspension system. The passive damping plate is installed under the Halbach permanent magnet array. When the vehicle‐mounted Halbach array and passive damping plate move to cut the track conductive plate, the 2D eddy current force is derived by establishing equations of magnetic vector potentials and using the Maxwell stress tensor method. And a 2D finite‐element model (FEM) is built to validate the accuracy of the derived levitation force equation. Based on the derived levitation force equation, the vertical stability of the PM EDS system with a passive damping plate and the effects of the main parameters on the damping ratio are analysed.
- 21 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (7) , 8679-8695
Analytical Methods for Estimating the Equivalent Stray Capacitance of Single-Layer Core Windings
The analytical methods for estimating the equivalent stray capacitance (ESC) in a single-layer iron core winding include the capacitance network method (CNM) and the energy equivalence method (EEM). The CNM is limited to applications in symmetrical windings, and the EEM is restricted to use in multiconductor systems (MCSs) with fully known potential distributions. These methods are improved in this paper. The winding symmetry limitation of the CNM is eliminated, and the EEM is used to calculate the ESC of MCSs containing floating potential conductors. ESC calculations are found to differ between the CNM and the EEM. The accuracies of the hypotheses used in the CNM and the EEM and the ESCs calculated with each approach are assessed and compared based on finite element simulations, circuit simulations and experiments. The results show that at the first resonant frequency condition, the EEM hypothesis is more consistent with reality than that of the CNM, and the ESC calculated with the EEM is more accurate. The ESC errors incurred when using the CNM and the EEM are mainly due to model errors introduced by the discrepancies between the assumptions and the actual conditions.
- 21 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (7) , 8679-8695
Analytical Methods for Estimating the Equivalent Stray Capacitance of Single-Layer Core Windings
The analytical methods for estimating the equivalent stray capacitance (ESC) in a single-layer iron core winding include the capacitance network method (CNM) and the energy equivalence method (EEM). The CNM is limited to applications in symmetrical windings, and the EEM is restricted to use in multiconductor systems (MCSs) with fully known potential distributions. These methods are improved in this paper. The winding symmetry limitation of the CNM is eliminated, and the EEM is used to calculate the ESC of MCSs containing floating potential conductors. ESC calculations are found to differ between the CNM and the EEM. The accuracies of the hypotheses used in the CNM and the EEM and the ESCs calculated with each approach are assessed and compared based on finite element simulations, circuit simulations and experiments. The results show that at the first resonant frequency condition, the EEM hypothesis is more consistent with reality than that of the CNM, and the ESC calculated with the EEM is more accurate. The ESC errors incurred when using the CNM and the EEM are mainly due to model errors introduced by the discrepancies between the assumptions and the actual conditions.
- 20 May 2020
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 15 (4) , 1713-1721
3D Analytical Model of Permanent Magnet and Electromagnetic Hybrid Halbach Array Electrodynamic Suspension System
- 20 May 2020
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 15 (4) , 1713-1721
3D Analytical Model of Permanent Magnet and Electromagnetic Hybrid Halbach Array Electrodynamic Suspension System
- 8 January 2020
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 15 (2) , 969-977
Study of Permanent Magnet Electrodynamic Suspension System with a Novel Halbach Array
- 8 January 2020
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 15 (2) , 969-977
Study of Permanent Magnet Electrodynamic Suspension System with a Novel Halbach Array