Adhiyamaan Arivazhagan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Adhiyamaan Arivazhagan has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Prabhu Raja Venugopal
Department of Mechanical Engineering, PSG College of Technology 2 , Avinashi Rd., Peelamedu, Coimbatore, Tamil Nadu 641004
2 shared publicationsAmmar Saleem
Faculty of Science, Engineering and Technology Swinburne University of Technology Melbourne Australia
1 shared publicationAshfaq Mohammad
Department of Mechanical Engineering, The University of Sheffield 3 , Western Bank, Sheffield, S10 2TN
1 shared publication- B. Vaishnavi
Department of Mechanical Engineering, PSG College of Technology, Coimbatore, India
1 shared publication Bolin Huang
Faculty of Science, Engineering and Technology Swinburne University of Technology Melbourne Australia
1 shared publication- D. J. Hiran Gabriel
PSG College of Technology
1 shared publication
Latest Publications
- 13 September 2022
- Published by Springer Nature
- p. 235-244
Wear and Hardness Behavior of Duplex-Treated AISI 1045 and AISI 4142 Steels
- 13 September 2022
- Published by Springer Nature
- p. 235-244
Wear and Hardness Behavior of Duplex-Treated AISI 1045 and AISI 4142 Steels
- 22 February 2021
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 49 (6) , 4326-4343
Influence of Magnesium Infiltration on Compressive Behavior of Additively Manufactured Porous Ti6Al4V Structure
As the next generation of metallic implants, Ti6Al4V porous structures have captivated more attention; however, the primitive compressive strength of the Ti6Al4V material is drastically reduced in its porous form while matching its Young’s modulus with that of the bone to avoid ‘stress-shielding effect’. This work sheds light on an unconventional approach to develop a metallic implant that addresses the twin demands of having high compressive strength and low Young’s modulus matching with that of the bone. This study focuses exclusively on the compressive behavior because most of the implants like hip and knee prosthesis are subjected to compressive loading. Porous Ti6Al4V structures with porosity ranging from 60–75 % are fabricated using electron beam melting, an additive manufacturing technique. And then, a pressureless infiltration technique is carried out to infiltrate pure magnesium, a good biodegradable material, into the porous structures by casting process. The compressive behavior of the infiltrated structures is analyzed and compared with porous Ti6Al4V structures. The compressive strength of the porous Ti6Al4V structures is enhanced up to 200 % after infiltrating it with biodegradable magnesium without much change in the modulus, making it a good candidate for the biomedical metallic implants. Moreover, the stress-strain characteristics of the magnesium-infiltrated Ti6Al4V samples exhibited ductile nature when compared with the stress-strain curves of the porous Ti6Al4V samples, which showed brittle nature, thereby enhancing the energy-absorbing quality of the metallic implant.
- 22 February 2021
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 49 (6) , 4326-4343
Influence of Magnesium Infiltration on Compressive Behavior of Additively Manufactured Porous Ti6Al4V Structure
As the next generation of metallic implants, Ti6Al4V porous structures have captivated more attention; however, the primitive compressive strength of the Ti6Al4V material is drastically reduced in its porous form while matching its Young’s modulus with that of the bone to avoid ‘stress-shielding effect’. This work sheds light on an unconventional approach to develop a metallic implant that addresses the twin demands of having high compressive strength and low Young’s modulus matching with that of the bone. This study focuses exclusively on the compressive behavior because most of the implants like hip and knee prosthesis are subjected to compressive loading. Porous Ti6Al4V structures with porosity ranging from 60–75 % are fabricated using electron beam melting, an additive manufacturing technique. And then, a pressureless infiltration technique is carried out to infiltrate pure magnesium, a good biodegradable material, into the porous structures by casting process. The compressive behavior of the infiltrated structures is analyzed and compared with porous Ti6Al4V structures. The compressive strength of the porous Ti6Al4V structures is enhanced up to 200 % after infiltrating it with biodegradable magnesium without much change in the modulus, making it a good candidate for the biomedical metallic implants. Moreover, the stress-strain characteristics of the magnesium-infiltrated Ti6Al4V samples exhibited ductile nature when compared with the stress-strain curves of the porous Ti6Al4V samples, which showed brittle nature, thereby enhancing the energy-absorbing quality of the metallic implant.
- Open Access
- 1 January 2016
- Published by Science Publications in American Journal of Engineering and Applied Sciences
- Vol. 9 (1) , 1-11
Dynamic Mechanical Properties of Fused Deposition Modelling Processed Polyphenylsulfone Material
Dynamic Mechanical Properties of Fused Deposition Modelling Processed Polyphenylsulfone Material
- 1 January 2016
- Published by Science Publications in American Journal of Engineering and Applied Sciences
- Vol. 9 (1) , 1-11
Open AccessDynamic Mechanical Properties of Fused Deposition Modelling Processed Polyphenylsulfone Material
Dynamic Mechanical Properties of Fused Deposition Modelling Processed Polyphenylsulfone Material
- Open Access
- 1 March 2014
- Published by Science Publications in American Journal of Engineering and Applied Sciences
- Vol. 7 (3) , 307-315
STUDY OF DYNAMIC MECHANICAL PROPERTIES OF FUSED DEPOSITION MODELLING PROCESSED ULTEM MATERIAL
STUDY OF DYNAMIC MECHANICAL PROPERTIES OF FUSED DEPOSITION MODELLING PROCESSED ULTEM MATERIAL
- 1 March 2014
- Published by Science Publications in American Journal of Engineering and Applied Sciences
- Vol. 7 (3) , 307-315
Open AccessSTUDY OF DYNAMIC MECHANICAL PROPERTIES OF FUSED DEPOSITION MODELLING PROCESSED ULTEM MATERIAL
STUDY OF DYNAMIC MECHANICAL PROPERTIES OF FUSED DEPOSITION MODELLING PROCESSED ULTEM MATERIAL