Daqing Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Daqing Yang has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Shijun Guo
4 shared publicationsDaochun Li
School of Aeronautical Science and Engineering, Beihang University, Beijing, China
2 shared publications- Ali Elham
Department of Aeronautics and Astronautics, University of Southampton, Burgess Road, Southampton SO16 7QF, UK
1 shared publication Jinwu Xiang
School of Aeronautical Science and Engineering, Beihang University, Beijing, China
1 shared publication- Kai San Hon
Department of Aeronautics, Faculty of engineering , Imperial College London , London , United Kingdom
1 shared publication Natalia Matteo
Cranfield University
1 shared publication
Latest Publications
- Open Access
- 1 June 2022
- Published by Walter de Gruyter GmbH in Transactions on Aerospace Research
- Vol. 2022 (2) , 31-61
Development of a Flight Simulator for Conceptual Aircraft Design and Sizing
This article describes the development of a flight simulator module within the ADEMAO aircraft design framework to investigate the effects of novel airframe and propulsion technologies on new generations of aircraft. Methods used to develop and integrate the fight simulator into the overall design framework are described. The simulator is validated based on existing data from the Convair CV-880M and is then used to analyze an example case of a conceptual medium-range aircraft with advanced airframe technologies designed in the Sustainable and Energy-Efficient Aviation research cluster at the Institute of Aircraft Design and Lightweight Structures at the Technische Universität Braunschweig. Results show the deficiencies of the medium-range aircraft in short-period pitch and Dutch roll performance, and recommendations for modifications to the conceptual medium-range aircraft are drafted.
- 1 June 2022
- Published by Walter de Gruyter GmbH in Transactions on Aerospace Research
- Vol. 2022 (2) , 31-61
Open AccessDevelopment of a Flight Simulator for Conceptual Aircraft Design and Sizing
This article describes the development of a flight simulator module within the ADEMAO aircraft design framework to investigate the effects of novel airframe and propulsion technologies on new generations of aircraft. Methods used to develop and integrate the fight simulator into the overall design framework are described. The simulator is validated based on existing data from the Convair CV-880M and is then used to analyze an example case of a conceptual medium-range aircraft with advanced airframe technologies designed in the Sustainable and Energy-Efficient Aviation research cluster at the Institute of Aircraft Design and Lightweight Structures at the Technische Universität Braunschweig. Results show the deficiencies of the medium-range aircraft in short-period pitch and Dutch roll performance, and recommendations for modifications to the conceptual medium-range aircraft are drafted.
- 1 April 2020
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 138
Nonlinear aeroelastic behavior of an airfoil with free-play in transonic flow
- 1 April 2020
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 138
Nonlinear aeroelastic behavior of an airfoil with free-play in transonic flow
- 4 January 2016
- Published by Emerald Publishing in Aircraft Engineering and Aerospace Technology
- Vol. 88 (1) , 168-177
Active control design for an unmanned air vehicle with a morphing wing
Purpose – The purpose of this study is to develop an active controller of both leading-edge (LE) and trailing-edge (TE) control surfaces for an unmanned air vehicle (UAV) with a composite morphing wing. Design/methodology/approach – Instead of conventional hinged control surfaces, both LE and TE seamless control surfaces were integrated with the wing. Based on the longitudinal state space equation, the root locus plot of the morphing wing aircraft, with a stability augmented system, was constructed. Using the pole placement, the feedback gain matrix for an active control was obtained. Findings – The aerodynamic benefits of a morphing wing section are compared with a wing of a rigid control surface. However, the 3D morphing wing with a large sweptback angle produces a washout negative aeroelastic effect, which causes a significant reduction of the control effectiveness. The results show that the stability augmentation system can significantly improve the longitudinal controllability of an aircraft with a m...
- 4 January 2016
- Published by Emerald Publishing in Aircraft Engineering and Aerospace Technology
- Vol. 88 (1) , 168-177
Active control design for an unmanned air vehicle with a morphing wing
Purpose – The purpose of this study is to develop an active controller of both leading-edge (LE) and trailing-edge (TE) control surfaces for an unmanned air vehicle (UAV) with a composite morphing wing. Design/methodology/approach – Instead of conventional hinged control surfaces, both LE and TE seamless control surfaces were integrated with the wing. Based on the longitudinal state space equation, the root locus plot of the morphing wing aircraft, with a stability augmented system, was constructed. Using the pole placement, the feedback gain matrix for an active control was obtained. Findings – The aerodynamic benefits of a morphing wing section are compared with a wing of a rigid control surface. However, the 3D morphing wing with a large sweptback angle produces a washout negative aeroelastic effect, which causes a significant reduction of the control effectiveness. The results show that the stability augmentation system can significantly improve the longitudinal controllability of an aircraft with a m...
- 2 April 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8409, 84091X-84091X-10
Active control using control allocation for UAVs with seamless morphing wing
- 2 April 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8409, 84091X-84091X-10
Active control using control allocation for UAVs with seamless morphing wing
- 1 January 2009
- Published by Inderscience Publishers in International Journal of Modelling, Identification and Control
- Vol. 7 (3) , 225
Rolling active control for an aircraft of seamless aeroelastic wing
This paper presents an investigation into the controllability for an aircraft of seamless aeroelastic wing. The research is aimed at the design of control laws for the aircraft rolling by actively operating a pair of an unconventional hingeless flexible leading and trailing control surfaces at different flight speed. The main challenge is how to achieve a specified rolling rate for the aircraft when the control effectiveness drops down and even crosses over the rolling reversal point within the flight envelope. This phenomenon is mainly due to the aeroelastic effect of the large sweptback and highly flexible wing design for weight saving. The investigation shows that control laws varying with the flight speed can be designed to achieve the rolling control target.
- 1 January 2009
- Published by Inderscience Publishers in International Journal of Modelling, Identification and Control
- Vol. 7 (3) , 225
Rolling active control for an aircraft of seamless aeroelastic wing
This paper presents an investigation into the controllability for an aircraft of seamless aeroelastic wing. The research is aimed at the design of control laws for the aircraft rolling by actively operating a pair of an unconventional hingeless flexible leading and trailing control surfaces at different flight speed. The main challenge is how to achieve a specified rolling rate for the aircraft when the control effectiveness drops down and even crosses over the rolling reversal point within the flight envelope. This phenomenon is mainly due to the aeroelastic effect of the large sweptback and highly flexible wing design for weight saving. The investigation shows that control laws varying with the flight speed can be designed to achieve the rolling control target.