Zhiwei Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhiwei Li has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Junming Shao
Institute of Optics and Electronics, Chinese Academy of Sciences, Chengdu, China
3 shared publicationsBin Fan
Chinese Acad Sci, Inst Opt & Elect, Chengdu 610209, Peoples R China
2 shared publications- Bin Fan
Institute of Optics and Electronics, Chinese Academy of Sciences, Chengdu 610209, China
2 shared publications - Shibin Wu
Institute of Optics and Electronics, Chinese Academy of Sciences, Chengdu, China
2 shared publications - Bincheng Li
School of Optoelectronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
1 shared publication Boping Lei
Institute of Optics and Electronics, Chinese Academy of Sciences, P.O. Box 350, Chengdu 610209, China
1 shared publication
Latest Publications
- Open Access
- 6 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (21) , 1143-1146
Figure Correction of a Quartz Sub-Mirror for a Transmissive Diffractive Segmented Telescope by Reactive Ion Figuring
A quartz sub-mirror was figure-corrected in a parallel removal process for the first time. An Reactive Ion Figuring (RIF) process with a simple and universal masking method was demonstrated, and the 350-mm quartz sub-mirror was figure-corrected from the initial figure error of ~23 nm RMS to the final figure error of ~8 nm RMS in total effective figuring time of ~52 minutes after 4 iterations, which exhibited the actual potential of RIF on the figure-correction of quartz optical elements and the possibility on applying RIF to meet the requirement of mass production for sub-mirrors of transmissive diffractive segmented telescopes.
- 6 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (21) , 1143-1146
Open AccessFigure Correction of a Quartz Sub-Mirror for a Transmissive Diffractive Segmented Telescope by Reactive Ion Figuring
A quartz sub-mirror was figure-corrected in a parallel removal process for the first time. An Reactive Ion Figuring (RIF) process with a simple and universal masking method was demonstrated, and the 350-mm quartz sub-mirror was figure-corrected from the initial figure error of ~23 nm RMS to the final figure error of ~8 nm RMS in total effective figuring time of ~52 minutes after 4 iterations, which exhibited the actual potential of RIF on the figure-correction of quartz optical elements and the possibility on applying RIF to meet the requirement of mass production for sub-mirrors of transmissive diffractive segmented telescopes.
- 23 October 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (22) , 33739-33746
Improved etching uniformity using equivalent electrodes on an unconventional, irregular membrane optical element for large aperture diffractive optical telescopes
The etching uniformity of diffractive membrane optical elements with an irregular shape was investigated. A deteriorative uniformity of electron number density and electron temperature was found according to finite element analysis of plasma discharge. A designable equivalent electrode was proposed to weaken the influence of introducing the unconventional, irregular sample. Improved uniformity of etching depths was demonstrated experimentally, assisting by the designable equivalent electrode. The demonstration of the designable equivalent electrode provides a beneficial solution for the fabrication of unconventional optical elements and an effective means for adjusting and controlling plasma characteristics.
- 23 October 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (22) , 33739-33746
Improved etching uniformity using equivalent electrodes on an unconventional, irregular membrane optical element for large aperture diffractive optical telescopes
The etching uniformity of diffractive membrane optical elements with an irregular shape was investigated. A deteriorative uniformity of electron number density and electron temperature was found according to finite element analysis of plasma discharge. A designable equivalent electrode was proposed to weaken the influence of introducing the unconventional, irregular sample. Improved uniformity of etching depths was demonstrated experimentally, assisting by the designable equivalent electrode. The demonstration of the designable equivalent electrode provides a beneficial solution for the fabrication of unconventional optical elements and an effective means for adjusting and controlling plasma characteristics.
- Open Access
Investigation of Photoelastic Property and Stress Analysis for Optical Polyimide Membrane through Stress Birefringence Method
Optical polyimide (PI) membranes have been increasingly attractive in optoelectronic substrate and optical element material applications. Controlled stress distribution is very important to optical PI membrane-based optics. However, nondestructive absolute stress measurement inside optical PI membranes remains challenging. In this letter, we adopted the stress birefringence method to experimentally investigate the correlation between stress and retardation in uniaxially, biaxially, and circularly stretched PI membranes. The calculated value of the photoelastic coefficient was found to be around 400 nm/Mpa·cm. A theoretical model was established where the retardation angle is the negative arctan of the principal stress ratio in the biaxially stretched membrane. We also found that the average retardation angle is an important parameter for evaluating the uniformity of stretching force in the circularly stretched membrane. This work provides a better understanding of the stress birefringence measurement of membrane materials.
Open AccessInvestigation of Photoelastic Property and Stress Analysis for Optical Polyimide Membrane through Stress Birefringence Method
Optical polyimide (PI) membranes have been increasingly attractive in optoelectronic substrate and optical element material applications. Controlled stress distribution is very important to optical PI membrane-based optics. However, nondestructive absolute stress measurement inside optical PI membranes remains challenging. In this letter, we adopted the stress birefringence method to experimentally investigate the correlation between stress and retardation in uniaxially, biaxially, and circularly stretched PI membranes. The calculated value of the photoelastic coefficient was found to be around 400 nm/Mpa·cm. A theoretical model was established where the retardation angle is the negative arctan of the principal stress ratio in the biaxially stretched membrane. We also found that the average retardation angle is an important parameter for evaluating the uniformity of stretching force in the circularly stretched membrane. This work provides a better understanding of the stress birefringence measurement of membrane materials.
- 18 November 2019
- Published by Optica Publishing Group in OSA Continuum
- Vol. 2 (12) , 3350-3357
Highly accurate positioned, rapid figure correction by reactive ion etching for large aperture lightweight membrane optical elements
Diffractive membrane optics has been expected to meet the requirement of large aperture space-based telescopes. However, the flexible membrane has different properties from traditional materials that the desired geometrical form is hardly obtained by current ultra-precision surface manufacturing technologies. A 400 mm aperture membrane substrate was figure-corrected by reactive ion etching from the initial figure error of 105 nm rms to the final figure error of ∼17 nm rms in total effective figuring time of ∼7.5 minutes. The RIE figuring technique with high position accuracy, nanometer level repeatability, and parallel removal manner has exhibited huge potential in figure correction.
- 18 November 2019
- Published by Optica Publishing Group in OSA Continuum
- Vol. 2 (12) , 3350-3357
Highly accurate positioned, rapid figure correction by reactive ion etching for large aperture lightweight membrane optical elements
Diffractive membrane optics has been expected to meet the requirement of large aperture space-based telescopes. However, the flexible membrane has different properties from traditional materials that the desired geometrical form is hardly obtained by current ultra-precision surface manufacturing technologies. A 400 mm aperture membrane substrate was figure-corrected by reactive ion etching from the initial figure error of 105 nm rms to the final figure error of ∼17 nm rms in total effective figuring time of ∼7.5 minutes. The RIE figuring technique with high position accuracy, nanometer level repeatability, and parallel removal manner has exhibited huge potential in figure correction.