William Corrêa Radünz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
William Corrêa Radünz has a total of 81 co-authors. Here are the top co-authors by number of shared publications:
- Bruno Souza Carmo
University of Sao Paulo, Sao Paulo, Brazil
6 shared publications - Julie Kay Lundquist
Department of Mechanical Engineering, Johns Hopkins University
6 shared publications - Adam S. Wise
Lawrence Livermore National Laboratory, Livermore, CA, USA
5 shared publications Raj K. Rai
Pacific Northwest National Laboratory, Richland, WA, USA
5 shared publications- Lawrence Cheung
Sandia National Laboratories California (Livermore, United States of America)
4 shared publications - Nicola Bodini
National Laboratory of the Rockies, Golden, CO, USA
4 shared publications
Latest Publications
- Open Access
- 27 August 2026
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 11 (8) , 3107-3135
The AWAKEN wind farm benchmark – Part 2: Modeling results
Accurately modeling wind farm performance in complex atmospheric flows remains a challenge. This paper presents the modeling results of the American WAKE experimeNt (AWAKEN) wind farm benchmark, a collaborative effort involving 16 research groups from academia and industry within the International Energy Agency Wind Technology Collaboration Programme Task 57. The study evaluates a diverse suite of simulation tools, ranging from fast-running engineering wake models to high-fidelity large-eddy simulations, against a diurnal case study observed during the AWAKEN campaign. The benchmark utilized a three-phase structure to progressively assess model performance as observational data availability increased. Initial blind predictions showed that higher-fidelity models did not uniformly outperform simpler simulation tools in terms of aggregate error metrics; however, this largely reflects differences in inflow strategy rather than wake physics fidelity – simpler models directly ingested high-quality observations, while higher-fidelity models were tasked with predicting the inflow from coarser reanalysis boundary conditions. A distinct spatial bias was observed where models struggled to resolve the interplay between a low-level jet, wakes, and terrain-induced flow acceleration. In subsequent phases, access to progressively richer observational data enabled model refinement that reduced mean absolute error by up to 40 %; however, these gains primarily reflect state-conditioned calibration to a well-observed atmospheric state. Overall, the study demonstrates that inflow characterization defines a lower bound on achievable model accuracy that is independent of wake modeling fidelity – a finding with direct implications for pre-construction energy assessment workflows. While the limited ability to resolve local terrain-flow interactions under single-day conditions represents a recognized constraint, the findings on wake modeling and real-world validation still provide valuable guidance for model application and future benchmark design.
- 27 August 2026
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 11 (8) , 3107-3135
Open AccessThe AWAKEN wind farm benchmark – Part 2: Modeling results
Accurately modeling wind farm performance in complex atmospheric flows remains a challenge. This paper presents the modeling results of the American WAKE experimeNt (AWAKEN) wind farm benchmark, a collaborative effort involving 16 research groups from academia and industry within the International Energy Agency Wind Technology Collaboration Programme Task 57. The study evaluates a diverse suite of simulation tools, ranging from fast-running engineering wake models to high-fidelity large-eddy simulations, against a diurnal case study observed during the AWAKEN campaign. The benchmark utilized a three-phase structure to progressively assess model performance as observational data availability increased. Initial blind predictions showed that higher-fidelity models did not uniformly outperform simpler simulation tools in terms of aggregate error metrics; however, this largely reflects differences in inflow strategy rather than wake physics fidelity – simpler models directly ingested high-quality observations, while higher-fidelity models were tasked with predicting the inflow from coarser reanalysis boundary conditions. A distinct spatial bias was observed where models struggled to resolve the interplay between a low-level jet, wakes, and terrain-induced flow acceleration. In subsequent phases, access to progressively richer observational data enabled model refinement that reduced mean absolute error by up to 40 %; however, these gains primarily reflect state-conditioned calibration to a well-observed atmospheric state. Overall, the study demonstrates that inflow characterization defines a lower bound on achievable model accuracy that is independent of wake modeling fidelity – a finding with direct implications for pre-construction energy assessment workflows. While the limited ability to resolve local terrain-flow interactions under single-day conditions represents a recognized constraint, the findings on wake modeling and real-world validation still provide valuable guidance for model application and future benchmark design.
- Open Access
- 30 July 2026
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 11 (7) , 2723-2747
Slow wake recovery and low turbulence behind wind farms parameterized in mesoscale simulations
Numerical weather prediction (NWP) and climate models equipped with wind-farm parameterizations (WFPs) can simulate cluster wake effects affecting downstream wind farms in both onshore and offshore environments. This study evaluates wake recovery behind a wind farm represented by the NWP-WFP approach in the Weather Research and Forecasting (WRF) model using either the Fitch et al. (2012) or Ma et al. (2022a, b) WFPs. Results are benchmarked against large-eddy simulations (LES) of an idealized offshore wind farm with aligned and staggered layouts under neutral atmospheric stability. Near-farm wake recovery is underestimated in NWP-WFP simulations due to its representation on a coarse mesoscale grid. This limitation leads to slow wake recovery through two interconnected mechanisms: (i) spatial gradients in the wind velocity field are weaker compared to LES and (ii) turbulence kinetic energy (TKE) remains low not because of excessive dissipation but due to insufficient shear production caused by these weakened gradients. For the scenario considered here, a wind-speed bias develops in the near-farm wake and persists into the far wake. Differences between the NWP-WFP simulations and LES emerge within a short distance downstream of the farm exit, where the mesoscale simulations recover too slowly. This reduced recovery contributes approximately 0.15–0.50 m s −1 to the near-farm wind-speed bias. The bias established in this region is not subsequently compensated for downstream but instead propagates into the far wake, where wind-speed differences of approximately 0.4–0.6 m s −1 remain up to 50 km downstream. Higher-resolution mesoscale simulations partially reduce this bias. Increasing turbine-added TKE or including subgrid wake effects provides additional improvement, but neither fully addresses the underlying cause. The slow wake recovery is not caused by limitations of the WFPs themselves, as it also occurs outside their region of influence, and adding subgrid wake effects does not significantly impact recovery. Rather, the slow wake recovery is a consequence of mesoscale flow representation. This behavior is not limited to regions downstream of the wind farm but is less visible within the farm, where wake recovery occurs simultaneously with turbine-induced momentum extraction. These results highlight the need for improved representations of wake recovery both within and downstream of wind farms. While enhanced subgrid modeling, shear-driven TKE production, and refined WFP formulations may improve intra-farm dynamics, accurately capturing near-farm wake recovery downstream remains challenging, as WFPs do not act in this region.
- 30 July 2026
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 11 (7) , 2723-2747
Open AccessSlow wake recovery and low turbulence behind wind farms parameterized in mesoscale simulations
Numerical weather prediction (NWP) and climate models equipped with wind-farm parameterizations (WFPs) can simulate cluster wake effects affecting downstream wind farms in both onshore and offshore environments. This study evaluates wake recovery behind a wind farm represented by the NWP-WFP approach in the Weather Research and Forecasting (WRF) model using either the Fitch et al. (2012) or Ma et al. (2022a, b) WFPs. Results are benchmarked against large-eddy simulations (LES) of an idealized offshore wind farm with aligned and staggered layouts under neutral atmospheric stability. Near-farm wake recovery is underestimated in NWP-WFP simulations due to its representation on a coarse mesoscale grid. This limitation leads to slow wake recovery through two interconnected mechanisms: (i) spatial gradients in the wind velocity field are weaker compared to LES and (ii) turbulence kinetic energy (TKE) remains low not because of excessive dissipation but due to insufficient shear production caused by these weakened gradients. For the scenario considered here, a wind-speed bias develops in the near-farm wake and persists into the far wake. Differences between the NWP-WFP simulations and LES emerge within a short distance downstream of the farm exit, where the mesoscale simulations recover too slowly. This reduced recovery contributes approximately 0.15–0.50 m s −1 to the near-farm wind-speed bias. The bias established in this region is not subsequently compensated for downstream but instead propagates into the far wake, where wind-speed differences of approximately 0.4–0.6 m s −1 remain up to 50 km downstream. Higher-resolution mesoscale simulations partially reduce this bias. Increasing turbine-added TKE or including subgrid wake effects provides additional improvement, but neither fully addresses the underlying cause. The slow wake recovery is not caused by limitations of the WFPs themselves, as it also occurs outside their region of influence, and adding subgrid wake effects does not significantly impact recovery. Rather, the slow wake recovery is a consequence of mesoscale flow representation. This behavior is not limited to regions downstream of the wind farm but is less visible within the farm, where wake recovery occurs simultaneously with turbine-induced momentum extraction. These results highlight the need for improved representations of wake recovery both within and downstream of wind farms. While enhanced subgrid modeling, shear-driven TKE production, and refined WFP formulations may improve intra-farm dynamics, accurately capturing near-farm wake recovery downstream remains challenging, as WFPs do not act in this region.
- Open Access
- 24 March 2026
- Published by Copernicus GmbH in EGUsphere
- Vol. 2026, 1-38
The AWAKEN wind farm benchmark, Part 2: Modeling results
Accurately modeling wind farm performance in complex atmospheric flows remains a challenge. This paper presents the modeling results of the American WAKE experimeNt (AWAKEN) wind farm benchmark, a collaborative effort involving 16 research groups from academia and industry within the International Energy Agency Wind Technology Collaboration Programme Task 57. The study evaluates a diverse suite of simulation tools, ranging from fast-running engineering wake models to high-fidelity large-eddy simulations, against a diurnal case study observed during the AWAKEN campaign. The benchmark utilized a three-phase structure to progressively assess model performance as observational data availability increased. Initial blind predictions showed that higher-fidelity models did not uniformly outperform simpler simulation tools. A distinct spatial bias was observed where models struggled to resolve the interplay between a low-level jet, wakes, and terrain-induced flow acceleration. In subsequent phases, leveraging additional measurements for model improvement led to a reduction in mean absolute error across the model ensemble; however, this effect was most pronounced in engineering wake models, where targeted calibration reduced error by up to 40 %. Overall, the study demonstrates that inflow characterization remains a primary prerequisite for accuracy, particularly for models relying on coarse forcing datasets. While the limited ability to resolve local terrain-flow interactions under single-day conditions represent a recognized constraint, the overall findings on wake modeling and real-world validation still provide valuable guidance for model application and for mitigating this limitation.
- 24 March 2026
- Published by Copernicus GmbH in EGUsphere
- Vol. 2026, 1-38
Open AccessThe AWAKEN wind farm benchmark, Part 2: Modeling results
Accurately modeling wind farm performance in complex atmospheric flows remains a challenge. This paper presents the modeling results of the American WAKE experimeNt (AWAKEN) wind farm benchmark, a collaborative effort involving 16 research groups from academia and industry within the International Energy Agency Wind Technology Collaboration Programme Task 57. The study evaluates a diverse suite of simulation tools, ranging from fast-running engineering wake models to high-fidelity large-eddy simulations, against a diurnal case study observed during the AWAKEN campaign. The benchmark utilized a three-phase structure to progressively assess model performance as observational data availability increased. Initial blind predictions showed that higher-fidelity models did not uniformly outperform simpler simulation tools. A distinct spatial bias was observed where models struggled to resolve the interplay between a low-level jet, wakes, and terrain-induced flow acceleration. In subsequent phases, leveraging additional measurements for model improvement led to a reduction in mean absolute error across the model ensemble; however, this effect was most pronounced in engineering wake models, where targeted calibration reduced error by up to 40 %. Overall, the study demonstrates that inflow characterization remains a primary prerequisite for accuracy, particularly for models relying on coarse forcing datasets. While the limited ability to resolve local terrain-flow interactions under single-day conditions represent a recognized constraint, the overall findings on wake modeling and real-world validation still provide valuable guidance for model application and for mitigating this limitation.
- Open Access
- 24 March 2026
- Published by Copernicus GmbH
Supplementary material to "The AWAKEN wind farm benchmark, Part 2: Modeling results"
- 24 March 2026
- Published by Copernicus GmbH
Open AccessSupplementary material to "The AWAKEN wind farm benchmark, Part 2: Modeling results"
- Open Access
- 24 October 2025
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 10 (10) , 2365-2393
Influence of simple terrain on the spatial variability of a low-level jet and wind farm performance in the AWAKEN field campaign
In wind energy research, scientific challenges are often associated with complex terrain sites, where orography, vegetation, and buildings disrupt flow uniformity. However, even sites characterized as simple terrain can exhibit significant spatial variability in wind speed, particularly during stable boundary layers (SBLs) and low-level jets (LLJs). This study investigates these terrain interactions using both simulations and observations from the American WAKe ExperimeNt (AWAKEN). We employ a multiscale Weather Research and Forecasting (WRF) model simulation, integrating mesoscale forcing in the coarse domains and representing three rows of turbines from the King Plains wind farm as generalized actuator disks (GAD) in the large-eddy simulation (LES) domains. During a nocturnal LLJ event on 3 April 2023, the downstream, wake-affected turbine rows outperformed the upstream, unwaked row by 25 %–51 %. This counterintuitive result arises from terrain-induced streamwise variations in hub-height wind speed of approximately 4 m s−1 over 5 km – equivalent to ∼50 % of the upstream reference speed. This enhancement outweighs the wake-induced reduction in mean wind speed (∼12 %) and global blockage effects reported in the literature (∼1 %–3.4 %). The multiscale simulations capture the intra-farm spatial variability in power performance observed in SCADA data. Terrain-induced vertical displacement of the LLJ, coupled with large wind shear below the jet maximum, drives the substantial streamwise acceleration within the wind farm. These findings underscore the importance of accounting for spatial variability related to terrain, even in simple landscapes, particularly during LLJ conditions. Incorporating such effects into reduced-order modeling frameworks for wind farm design and control could significantly enhance their effectiveness.
- 24 October 2025
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 10 (10) , 2365-2393
Open AccessInfluence of simple terrain on the spatial variability of a low-level jet and wind farm performance in the AWAKEN field campaign
In wind energy research, scientific challenges are often associated with complex terrain sites, where orography, vegetation, and buildings disrupt flow uniformity. However, even sites characterized as simple terrain can exhibit significant spatial variability in wind speed, particularly during stable boundary layers (SBLs) and low-level jets (LLJs). This study investigates these terrain interactions using both simulations and observations from the American WAKe ExperimeNt (AWAKEN). We employ a multiscale Weather Research and Forecasting (WRF) model simulation, integrating mesoscale forcing in the coarse domains and representing three rows of turbines from the King Plains wind farm as generalized actuator disks (GAD) in the large-eddy simulation (LES) domains. During a nocturnal LLJ event on 3 April 2023, the downstream, wake-affected turbine rows outperformed the upstream, unwaked row by 25 %–51 %. This counterintuitive result arises from terrain-induced streamwise variations in hub-height wind speed of approximately 4 m s−1 over 5 km – equivalent to ∼50 % of the upstream reference speed. This enhancement outweighs the wake-induced reduction in mean wind speed (∼12 %) and global blockage effects reported in the literature (∼1 %–3.4 %). The multiscale simulations capture the intra-farm spatial variability in power performance observed in SCADA data. Terrain-induced vertical displacement of the LLJ, coupled with large wind shear below the jet maximum, drives the substantial streamwise acceleration within the wind farm. These findings underscore the importance of accounting for spatial variability related to terrain, even in simple landscapes, particularly during LLJ conditions. Incorporating such effects into reduced-order modeling frameworks for wind farm design and control could significantly enhance their effectiveness.
- Open Access
- 20 August 2025
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 10 (8) , 1681-1705
Operational wind plants increase planetary boundary layer height: an observational study
As wind energy deployment grows, interactions between wind plants and the surrounding environment become more prevalent. The current investigation seeks to understand these interactions by characterizing the impact of wind plants on the planetary boundary layer height (PBLH), utilizing observations from the American WAKE experimeNt (AWAKEN) campaign. Given the ambiguity of the definition of PBLH under stable atmospheric conditions, where the impact of wind plants is expected to be strongest, a comparison of different methods for identifying PBLH is first conducted using data collected by multiple types of instruments. The Heffter method is selected as the thermodynamic method because it generates the most consistent results for the radiosonde and infrared spectrometer. A minimum vertical velocity variance method is used for a turbulence-based definition. Using both of these methods, the values of PBLH measured at spatially distributed sites are compared under a range of atmospheric conditions. Both methods show a clear increase in PBLH downstream of a wind plant for stable conditions. These impacts are strongest when the upstream PBLH is shallow (less than 0.25 km), with the thermodynamic method showing a PBLH increase of 35 %–39 % and the turbulence-based method showing a 143 % increase. At a site 20 km downstream of the wind plant, these effects are no longer observed, suggesting PBLH is not influenced by the wind plant at this distance. The results of this investigation show that wind plants can modify PBLH in their vicinity. As PBLH is a key parameter for numerical models, this insight into wind plant–atmosphere interactions can be used to validate and improve the accuracy of wind energy forecasts.
- 20 August 2025
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 10 (8) , 1681-1705
Open AccessOperational wind plants increase planetary boundary layer height: an observational study
As wind energy deployment grows, interactions between wind plants and the surrounding environment become more prevalent. The current investigation seeks to understand these interactions by characterizing the impact of wind plants on the planetary boundary layer height (PBLH), utilizing observations from the American WAKE experimeNt (AWAKEN) campaign. Given the ambiguity of the definition of PBLH under stable atmospheric conditions, where the impact of wind plants is expected to be strongest, a comparison of different methods for identifying PBLH is first conducted using data collected by multiple types of instruments. The Heffter method is selected as the thermodynamic method because it generates the most consistent results for the radiosonde and infrared spectrometer. A minimum vertical velocity variance method is used for a turbulence-based definition. Using both of these methods, the values of PBLH measured at spatially distributed sites are compared under a range of atmospheric conditions. Both methods show a clear increase in PBLH downstream of a wind plant for stable conditions. These impacts are strongest when the upstream PBLH is shallow (less than 0.25 km), with the thermodynamic method showing a PBLH increase of 35 %–39 % and the turbulence-based method showing a 143 % increase. At a site 20 km downstream of the wind plant, these effects are no longer observed, suggesting PBLH is not influenced by the wind plant at this distance. The results of this investigation show that wind plants can modify PBLH in their vicinity. As PBLH is a key parameter for numerical models, this insight into wind plant–atmosphere interactions can be used to validate and improve the accuracy of wind energy forecasts.
- 1 May 2025
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 17 (3)
Offshore wind profile extrapolation effects on energy production estimates in Southeast Brazil
This research examines how stable stratifications occur and influence energy production predictions along Brazil's Southeast offshore region. The investigation focuses on a notable stable condition on July 3, 2019, detailed in a spatiotemporal analysis using the reanalysis dataset and a numerical atmospheric model. Moreover, we analyze reanalysis data of the air temperature at 2 m and the sea surface temperature (SST) to investigate the influence of atmospheric stability in the surface layer. We also measured the wind up to a height of 150 m using a wind profiler at a floating production storage and offloading vessel located about 190 km off the coast in the pre-salt oil extraction region. Stable conditions arise when warm air in the vanguard of the cold front passes over a relatively colder sea surface. An important finding reveals that air and sea are locally decoupled, where the wind profile is modified before the air surface temperature surpasses the sea surface temperature at the vessel due to the stable upstream conditions associated with the upwelling of cold water near the coast. Finally, we assess the stable stratification effects on annual energy production using three methods to extrapolate wind speeds from reanalysis data at a reference altitude of 100 m to the hub height of 150 m for a reference 15 MW wind turbine. Our results indicate that extrapolation methods for stable conditions may lead to overprediction in annual energy production projections ranging from 1.2% to 9.7%.
- 1 May 2025
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 17 (3)
Offshore wind profile extrapolation effects on energy production estimates in Southeast Brazil
This research examines how stable stratifications occur and influence energy production predictions along Brazil's Southeast offshore region. The investigation focuses on a notable stable condition on July 3, 2019, detailed in a spatiotemporal analysis using the reanalysis dataset and a numerical atmospheric model. Moreover, we analyze reanalysis data of the air temperature at 2 m and the sea surface temperature (SST) to investigate the influence of atmospheric stability in the surface layer. We also measured the wind up to a height of 150 m using a wind profiler at a floating production storage and offloading vessel located about 190 km off the coast in the pre-salt oil extraction region. Stable conditions arise when warm air in the vanguard of the cold front passes over a relatively colder sea surface. An important finding reveals that air and sea are locally decoupled, where the wind profile is modified before the air surface temperature surpasses the sea surface temperature at the vessel due to the stable upstream conditions associated with the upwelling of cold water near the coast. Finally, we assess the stable stratification effects on annual energy production using three methods to extrapolate wind speeds from reanalysis data at a reference altitude of 100 m to the hub height of 150 m for a reference 15 MW wind turbine. Our results indicate that extrapolation methods for stable conditions may lead to overprediction in annual energy production projections ranging from 1.2% to 9.7%.
- Open Access
- 1 March 2025
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 17 (2)
Model intercomparison of the ABL, turbines, and wakes within the AWAKEN wind farms under neutral stability conditions
In previous work, comparisons were made between large-scale simulations of the American Wake ExperimeNt (AWAKEN) wind farms conducted using the large-eddy simulation (LES) codes Nalu-Wind and Adaptive Mesh Refinement-Wind, the engineering wind farm model FLOw Redirection and Induction in Steady State (FLORIS), and the multi-scale Weather Research and Forecasting model. Significant discrepancies were observed in the modeled wake deficits, and the present paper investigates the sources of this model variability using new simulations with single turbines and smaller domains. From an experimental data set taken from AWAKEN, an idealized neutral stability condition was defined and single-turbine cases using actuator disk were conducted with the different simulation codes allowing for a comprehensive investigation into the similarities and differences between the atmospheric inflow, turbines, and wakes of the simulations. Improvements to the simulation setups in the present study resulted in significantly higher agreement between the modeled results from the three LES models and FLORIS.
- 1 March 2025
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 17 (2)
Open AccessModel intercomparison of the ABL, turbines, and wakes within the AWAKEN wind farms under neutral stability conditions
In previous work, comparisons were made between large-scale simulations of the American Wake ExperimeNt (AWAKEN) wind farms conducted using the large-eddy simulation (LES) codes Nalu-Wind and Adaptive Mesh Refinement-Wind, the engineering wind farm model FLOw Redirection and Induction in Steady State (FLORIS), and the multi-scale Weather Research and Forecasting model. Significant discrepancies were observed in the modeled wake deficits, and the present paper investigates the sources of this model variability using new simulations with single turbines and smaller domains. From an experimental data set taken from AWAKEN, an idealized neutral stability condition was defined and single-turbine cases using actuator disk were conducted with the different simulation codes allowing for a comprehensive investigation into the similarities and differences between the atmospheric inflow, turbines, and wakes of the simulations. Improvements to the simulation setups in the present study resulted in significantly higher agreement between the modeled results from the three LES models and FLORIS.
- Open Access
- 8 January 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-38
Influence of simple terrain on the spatial variability of a low-level jet and wind farm performance in the AWAKEN field campaign
In wind energy research, scientific challenges are often associated with complex terrain sites, where orography, vegetation, and buildings disrupt flow uniformity. However, even sites characterized as simple terrain can exhibit significant spatial variability in wind speed, particularly during stable boundary layers (SBLs) and low-level jets (LLJs). This study investigates these terrain interactions using both simulations and observations from the American WAKe ExperimeNt (AWAKEN). We employ a multiscale Weather Research and Forecasting (WRF) model simulation, integrating mesoscale forcing in the coarse domains and representing three rows of turbines from the King Plains wind farm as generalized actuator disks (GAD) in the large-eddy simulation (LES) domains. During a nocturnal LLJ event on 3 April 2023, the downwind, wake-affected turbine rows outperformed the upwind, unwaked row by 25–51 %. This counterintuitive result arises from terrain-induced streamwise variations in hub-height wind speed of approximately 4 m s-1 over 5 km—equivalent to ~50 % of the upwind reference speed. This enhancement outweighs the wake-induced reduction in mean wind speed (~12 %) and global blockage effects reported in the literature (~1–3.4 %). The multiscale simulations capture the intra-farm spatial variability in power performance observed in SCADA data. Terrain-induced vertical displacement of the LLJ, coupled with large wind shear below the jet maximum, drives the substantial streamwise acceleration within the wind farm. These findings underscore the importance of accounting for spatial variability related to terrain, even in simple landscapes, particularly during LLJ conditions. Incorporating such effects into reduced-order modeling frameworks for wind farm design and control could significantly enhance their effectiveness.
- 8 January 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-38
Open AccessInfluence of simple terrain on the spatial variability of a low-level jet and wind farm performance in the AWAKEN field campaign
In wind energy research, scientific challenges are often associated with complex terrain sites, where orography, vegetation, and buildings disrupt flow uniformity. However, even sites characterized as simple terrain can exhibit significant spatial variability in wind speed, particularly during stable boundary layers (SBLs) and low-level jets (LLJs). This study investigates these terrain interactions using both simulations and observations from the American WAKe ExperimeNt (AWAKEN). We employ a multiscale Weather Research and Forecasting (WRF) model simulation, integrating mesoscale forcing in the coarse domains and representing three rows of turbines from the King Plains wind farm as generalized actuator disks (GAD) in the large-eddy simulation (LES) domains. During a nocturnal LLJ event on 3 April 2023, the downwind, wake-affected turbine rows outperformed the upwind, unwaked row by 25–51 %. This counterintuitive result arises from terrain-induced streamwise variations in hub-height wind speed of approximately 4 m s-1 over 5 km—equivalent to ~50 % of the upwind reference speed. This enhancement outweighs the wake-induced reduction in mean wind speed (~12 %) and global blockage effects reported in the literature (~1–3.4 %). The multiscale simulations capture the intra-farm spatial variability in power performance observed in SCADA data. Terrain-induced vertical displacement of the LLJ, coupled with large wind shear below the jet maximum, drives the substantial streamwise acceleration within the wind farm. These findings underscore the importance of accounting for spatial variability related to terrain, even in simple landscapes, particularly during LLJ conditions. Incorporating such effects into reduced-order modeling frameworks for wind farm design and control could significantly enhance their effectiveness.
- Open Access
- 16 August 2022
- Published by Associação Brasileira de Energia Solar in Anais Congresso Brasileiro de Energia Solar - CBENS
- p. 1-10
ESTUDO PRELIMINAR DA INFLUÊNCIA DE JATOS NOTURNOS E DA SAZONALIDADE NO DESEMPENHO DE LONGO PRAZO DE PARQUES EÓLICOS EM TERRENOS COMPLEXOS
This work aims to analyze field and reanalysis data over 3 years, to identify how nocturnal jets and large-scale effects impact the energy generation of the site. The Campo Formoso I wind farm is located in Bahia (close to 10º38' S and 40º42' W), the back row of turbines can exhibit up to 40% higher performance than the front rows during the night period in most months of the year in the period between January 2016 and December 2018, except for some cold and dry months (July and September). The presence of nocturnal jets can cause this performance to increase at night due to an interaction with the topography, as stated in another investigation. This work took the annual climatic variations of northeastern Brazil into consideration and used the division of stations suggested by Medeiros et al (2021) that divided them into two main seasons, the rainy season from January to April and the dry season from July to September, as well as the movement of the Intertropical Convergence Zone (ITCZ), which may reach 14ºN in August/September and 2ºS in March/April. The joint analysis of field data and reanalysis (ERA5) revealed that in some months of the dry season (July and September) large-scale winds reach Campo Formoso I and overlap the park's mesoscale winds, causing the front turbines to produce more energy than the back ones throughout the journey. The work intends to demonstrate how these phenomena were identified, to show that the movement of the ITCZ and the climatic variations of the seasons can be related to the wind changes, and finally discuss the impact of all this in the generation of the park. Este trabalho pretende analisar dados de campo e de reanálise em um período de 3 anos, para identificar como os jatos noturnos e os efeitos de grande escala impactam na produção do parque eólico. No complexo eólico de Campo Formoso I, localizado na Bahia (próximo a 10° 38′ S e 40° 42′ O), as turbinas da fileira traseira exibem um desempenho até 40% maior que as dianteiras durante o período noturno na maioria dos meses do ano do período entre janeiro de 2016 e dezembro de 2018, com exceção de alguns meses de clima frio e seco (julho e setembro). A presença de jatos noturnos pode causar esse aumento do desempenho durante a noite devido a uma interação com a topografia conforme descrito em outra investigação. Este trabalho considerou as variações climáticas anuais do nordeste brasileiro, e seguiu a sugestão de Medeiros et. al. (2021) que em sua pesquisa dividiu-as em duas estações principais, a estação chuvosa de janeiro a abril e a estação seca de julho a setembro, assim como o movimento da Zona de Convergência Intertropical (ZCIT), podendo chegar a 14º N em agosto/setembro e 2º S em março/abril. A análise conjunta dos dados de campo e reanálise (ERA5), revelou que em alguns meses da estação seca (julho e setembro) os ventos de grande escala sobrepõem-se aos ventos de mesoescala do parque, fazendo com que as turbinas dianteiras produzam mais energia do que as traseiras. O trabalho pretende demonstrar como esses fenômenos foram identificados, relacionar a movimentação da ZCIT e as variações climáticas das estações com as mudanças do vento, e finalmente discutir sobre o impacto de tudo isso na geração do parque.
- 16 August 2022
- Published by Associação Brasileira de Energia Solar in Anais Congresso Brasileiro de Energia Solar - CBENS
- p. 1-10
Open AccessESTUDO PRELIMINAR DA INFLUÊNCIA DE JATOS NOTURNOS E DA SAZONALIDADE NO DESEMPENHO DE LONGO PRAZO DE PARQUES EÓLICOS EM TERRENOS COMPLEXOS
This work aims to analyze field and reanalysis data over 3 years, to identify how nocturnal jets and large-scale effects impact the energy generation of the site. The Campo Formoso I wind farm is located in Bahia (close to 10º38' S and 40º42' W), the back row of turbines can exhibit up to 40% higher performance than the front rows during the night period in most months of the year in the period between January 2016 and December 2018, except for some cold and dry months (July and September). The presence of nocturnal jets can cause this performance to increase at night due to an interaction with the topography, as stated in another investigation. This work took the annual climatic variations of northeastern Brazil into consideration and used the division of stations suggested by Medeiros et al (2021) that divided them into two main seasons, the rainy season from January to April and the dry season from July to September, as well as the movement of the Intertropical Convergence Zone (ITCZ), which may reach 14ºN in August/September and 2ºS in March/April. The joint analysis of field data and reanalysis (ERA5) revealed that in some months of the dry season (July and September) large-scale winds reach Campo Formoso I and overlap the park's mesoscale winds, causing the front turbines to produce more energy than the back ones throughout the journey. The work intends to demonstrate how these phenomena were identified, to show that the movement of the ITCZ and the climatic variations of the seasons can be related to the wind changes, and finally discuss the impact of all this in the generation of the park. Este trabalho pretende analisar dados de campo e de reanálise em um período de 3 anos, para identificar como os jatos noturnos e os efeitos de grande escala impactam na produção do parque eólico. No complexo eólico de Campo Formoso I, localizado na Bahia (próximo a 10° 38′ S e 40° 42′ O), as turbinas da fileira traseira exibem um desempenho até 40% maior que as dianteiras durante o período noturno na maioria dos meses do ano do período entre janeiro de 2016 e dezembro de 2018, com exceção de alguns meses de clima frio e seco (julho e setembro). A presença de jatos noturnos pode causar esse aumento do desempenho durante a noite devido a uma interação com a topografia conforme descrito em outra investigação. Este trabalho considerou as variações climáticas anuais do nordeste brasileiro, e seguiu a sugestão de Medeiros et. al. (2021) que em sua pesquisa dividiu-as em duas estações principais, a estação chuvosa de janeiro a abril e a estação seca de julho a setembro, assim como o movimento da Zona de Convergência Intertropical (ZCIT), podendo chegar a 14º N em agosto/setembro e 2º S em março/abril. A análise conjunta dos dados de campo e reanálise (ERA5), revelou que em alguns meses da estação seca (julho e setembro) os ventos de grande escala sobrepõem-se aos ventos de mesoescala do parque, fazendo com que as turbinas dianteiras produzam mais energia do que as traseiras. O trabalho pretende demonstrar como esses fenômenos foram identificados, relacionar a movimentação da ZCIT e as variações climáticas das estações com as mudanças do vento, e finalmente discutir sobre o impacto de tudo isso na geração do parque.