Guoying Meng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Guoying Meng has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
Xiaohan Cheng
China Univ Min & Technol Beijing, Sch Mech Elect & Informat Engn, Room 313 Mech Elect Bldg,D11 Xueyuan Rd, Beijing 100083, Peoples R China
6 shared publications- Aiming Wang
School of Mechanical Electronic & Information Engineering, China University of Mining & Technology (Beijing), Beijing 100083, China
3 shared publications Wei Li
3 shared publicationsZhengduo Pang
China CAMC Engineering Co., Ltd., Beijing, China
3 shared publicationsJie Tian
School of Mechanical, Electronic, and Information Engineering, China University of Mining and Technology, Beijing 100083, China
2 shared publicationsJie Yang
2 shared publications
Latest Publications
- 23 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 9, 867-871
An Intelligent Diagnosis Method for Bearing Faults with Multiple Image Inputs and Deep Convolutional Neural Networks
Bearings are key transmission parts that are extensively used in rolling mechanical and equipment. Bearing failures can affect the regular running of machines, in serious cases, can cause enormous losses in economy and personnel casualties. Therefore, it is important to implement the research of diagnosing bearing faults. In this paper, a bearing faults diagnosis method was developed based on multiple image inputs and deep convolutional neural network. Firstly, the 1-Dvibration signal is transformed into three different types of two-dimensional images: time-frequency image, vibration grayscale image and symmetry dot pattern image, respectively. Enter them into multiple DCNNs separately. Finally, Finally, the nonlinear features of multiple DCNN outputs are fused and classified to achieve bearing fault diagnostics. The experimental results indicate that the diagnosis accuracy of this proposed method is 98.8%, it can extract the fault features of vibration samples well, and it is an effective bearing fault diagnosis methodology.
- 23 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 9, 867-871
An Intelligent Diagnosis Method for Bearing Faults with Multiple Image Inputs and Deep Convolutional Neural Networks
Bearings are key transmission parts that are extensively used in rolling mechanical and equipment. Bearing failures can affect the regular running of machines, in serious cases, can cause enormous losses in economy and personnel casualties. Therefore, it is important to implement the research of diagnosing bearing faults. In this paper, a bearing faults diagnosis method was developed based on multiple image inputs and deep convolutional neural network. Firstly, the 1-Dvibration signal is transformed into three different types of two-dimensional images: time-frequency image, vibration grayscale image and symmetry dot pattern image, respectively. Enter them into multiple DCNNs separately. Finally, Finally, the nonlinear features of multiple DCNN outputs are fused and classified to achieve bearing fault diagnostics. The experimental results indicate that the diagnosis accuracy of this proposed method is 98.8%, it can extract the fault features of vibration samples well, and it is an effective bearing fault diagnosis methodology.
- Open Access
- 25 October 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 128, 05015
Fault Diagnosis for Constant Deceleration Braking System of Mine Hoist based on Principal Component Analysis and SVM
Based on AMESim simulation platform, the pressure-time curve of constant deceleration braking system is obtained in this paper firstly, by simulating three typical faults of brake, the spring stiffness decrease, the brake shoe friction coefficient decrease and brake leaking. Then pressure data on the curve for each time are seen as a variable and the curve is chosen as the fault sample, analysed by the method of Principal Component Analysis (PCA). Last, principal components or sum of variance contribution rates more than 95% are selected as sample eigenvalues and Support Vector Machine (SVM) is used for fault diagnosis. Diagnosis results show that all testing faults can be identified accurately, which indicates SVM model has an extremely excellent ability to identify faults. To further verify the performance of SVM for fault identification, BP neural network is established to compare. The result shows that SVM model is more accurate than BP neural network in fault recognition.
- 25 October 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 128, 05015
Open AccessFault Diagnosis for Constant Deceleration Braking System of Mine Hoist based on Principal Component Analysis and SVM
Based on AMESim simulation platform, the pressure-time curve of constant deceleration braking system is obtained in this paper firstly, by simulating three typical faults of brake, the spring stiffness decrease, the brake shoe friction coefficient decrease and brake leaking. Then pressure data on the curve for each time are seen as a variable and the curve is chosen as the fault sample, analysed by the method of Principal Component Analysis (PCA). Last, principal components or sum of variance contribution rates more than 95% are selected as sample eigenvalues and Support Vector Machine (SVM) is used for fault diagnosis. Diagnosis results show that all testing faults can be identified accurately, which indicates SVM model has an extremely excellent ability to identify faults. To further verify the performance of SVM for fault identification, BP neural network is established to compare. The result shows that SVM model is more accurate than BP neural network in fault recognition.
- Open Access
- 30 September 2017
- Published by Academy and Industry Research Collaboration Center (AIRCC)
- p. 01-11
Fault Diagnosis in Braking System of Mine Hoist Based on the Moment Characteristics
- 30 September 2017
- Published by Academy and Industry Research Collaboration Center (AIRCC)
- p. 01-11
Open AccessFault Diagnosis in Braking System of Mine Hoist Based on the Moment Characteristics
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 226, 227-233
Kinematic modeling and simulation of wheeled pipe robot in elbow at planar motion stage
A study on the kinematics of wheeled pipe robot in elbow at planar motion stage is presented in this paper. Through analyzing the model of location and direction of robot, displacement functions of driving wheel centers corresponding to steering angle are derived. By taking the derivatives of displacement function and steering angle, the velocity of driving wheels and rotational speed of driving motors are calculated. On the basis of the calculated results, kinematic model of robot is set up. In order to identify the validity of the kinematic model, a couple of simulation experiments are carried out by using ADAMS software and comparisons both in theory and simulation are implemented. The comparisons suggest that theoretical values are in agreement with experimental results and the kinematic model is established effectively. This lays theoretical foundation for optimizing control method of robot entering into elbow by speed regulation technology.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 226, 227-233
Kinematic modeling and simulation of wheeled pipe robot in elbow at planar motion stage
A study on the kinematics of wheeled pipe robot in elbow at planar motion stage is presented in this paper. Through analyzing the model of location and direction of robot, displacement functions of driving wheel centers corresponding to steering angle are derived. By taking the derivatives of displacement function and steering angle, the velocity of driving wheels and rotational speed of driving motors are calculated. On the basis of the calculated results, kinematic model of robot is set up. In order to identify the validity of the kinematic model, a couple of simulation experiments are carried out by using ADAMS software and comparisons both in theory and simulation are implemented. The comparisons suggest that theoretical values are in agreement with experimental results and the kinematic model is established effectively. This lays theoretical foundation for optimizing control method of robot entering into elbow by speed regulation technology.
- 1 March 2017
- Published by British Institute of Non-Destructive Testing (BINDT) in Insight - Non-Destructive Testing and Condition Monitoring
- Vol. 59 (3) , 143-148
A sensor model for defect detection in mine hoisting wire ropes based on magnetic focusing
In view of the limitations in the currently applied defect detection techniques for the large-diameter hoisting wire ropes used in coal mines, this study proposes a new method for detecting magnetic excitation in wire ropes by combining the structural models for dynamic magnetic field balancing and magnetic focusing. The paper first describes a structural model that applies the principle of magnetic field balancing to integrate sensors for defect detection in wire ropes. Next, it presents the design of a structural model for magnetic focusing, which is applicable to large-diameter wire ropes and can achieve all-round detection without exception. A detection method that uses a Hall-element array in combination with the magnetic focusing technique, which can reduce the interference produced by the interactions between the environmental magnetic fields and the wire rope strand, is also proposed. Finally, the proposed detection sensor is tested through simulations and experiments. As the proposed sensor is equipped with a permanent magnet made of N35-type material, which has a smaller remanence and is 20 mm less wide and 20 mm less thick than conventional magnetic flux leakage defect detection sensors, the volume, weight and cost of the sensor is lower. Moreover, in comparison, the proposed sensor detected six defects accurately in the experiment, while the conventional sensor missed one. The signal-to-noise ratio of the proposed sensor is 6.5 dB higher than that of the conventional one, which reveals that it provides better detection capabilities.
- 1 March 2017
- Published by British Institute of Non-Destructive Testing (BINDT) in Insight - Non-Destructive Testing and Condition Monitoring
- Vol. 59 (3) , 143-148
A sensor model for defect detection in mine hoisting wire ropes based on magnetic focusing
In view of the limitations in the currently applied defect detection techniques for the large-diameter hoisting wire ropes used in coal mines, this study proposes a new method for detecting magnetic excitation in wire ropes by combining the structural models for dynamic magnetic field balancing and magnetic focusing. The paper first describes a structural model that applies the principle of magnetic field balancing to integrate sensors for defect detection in wire ropes. Next, it presents the design of a structural model for magnetic focusing, which is applicable to large-diameter wire ropes and can achieve all-round detection without exception. A detection method that uses a Hall-element array in combination with the magnetic focusing technique, which can reduce the interference produced by the interactions between the environmental magnetic fields and the wire rope strand, is also proposed. Finally, the proposed detection sensor is tested through simulations and experiments. As the proposed sensor is equipped with a permanent magnet made of N35-type material, which has a smaller remanence and is 20 mm less wide and 20 mm less thick than conventional magnetic flux leakage defect detection sensors, the volume, weight and cost of the sensor is lower. Moreover, in comparison, the proposed sensor detected six defects accurately in the experiment, while the conventional sensor missed one. The signal-to-noise ratio of the proposed sensor is 6.5 dB higher than that of the conventional one, which reveals that it provides better detection capabilities.
- 1 March 2017
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 86, 151-176
Dynamic analysis and numerical experiments for balancing of the continuous single-disc and single-span rotor-bearing system
- 1 March 2017
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 86, 151-176
Dynamic analysis and numerical experiments for balancing of the continuous single-disc and single-span rotor-bearing system
- Open Access
- 11 October 2016
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 8 (10)
Experimental study on the welding procedure of the central groove of armored face conveyor
The central groove is a key component of armored face conveyor. Failure of welded joints in the central groove often occurs in engineering. In this article, the welding procedure parameters were analyzed to the improve strength and toughness of the dissimilar steel weld joint in the central groove. First, four types of super-high wear-resistant steel and two types of high-strength welding wire were chosen as the welding materials. Carbon equivalent method, cold crack sensitivity index method, and maximum hardness of heat-affected zone test were applied to analyze their welding properties. Second, to improve their weldability, the proper preheating temperature was determined using Y-groove cracking test and mechanical property tests. Finally, a semi-automatic CO2 welding method was adopted, and a second mechanical property test was conducted to determine the proper welding wire. Results show that the chosen steels have poor weldability and cold cracking sensitivity. Preheating must be used to prevent cold cracking. When the preheating temperature is higher than 80°C, the cold crack rate can be controlled to under 20%, which can satisfy application requirements. Welding wire YMGR76 is appropriate. Using YMGR76, the preheating temperature drops to 120°C, and the strength and toughness of the weld joint are improved to 813 MPa and 112 KV2/J, respectively. This study provides a welding procedure to improve the reliability of the central groove.
- 11 October 2016
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 8 (10)
Open AccessExperimental study on the welding procedure of the central groove of armored face conveyor
The central groove is a key component of armored face conveyor. Failure of welded joints in the central groove often occurs in engineering. In this article, the welding procedure parameters were analyzed to the improve strength and toughness of the dissimilar steel weld joint in the central groove. First, four types of super-high wear-resistant steel and two types of high-strength welding wire were chosen as the welding materials. Carbon equivalent method, cold crack sensitivity index method, and maximum hardness of heat-affected zone test were applied to analyze their welding properties. Second, to improve their weldability, the proper preheating temperature was determined using Y-groove cracking test and mechanical property tests. Finally, a semi-automatic CO2 welding method was adopted, and a second mechanical property test was conducted to determine the proper welding wire. Results show that the chosen steels have poor weldability and cold cracking sensitivity. Preheating must be used to prevent cold cracking. When the preheating temperature is higher than 80°C, the cold crack rate can be controlled to under 20%, which can satisfy application requirements. Welding wire YMGR76 is appropriate. Using YMGR76, the preheating temperature drops to 120°C, and the strength and toughness of the weld joint are improved to 813 MPa and 112 KV2/J, respectively. This study provides a welding procedure to improve the reliability of the central groove.
- Open Access
- 3 November 2015
- Published by Elsevier in International Journal of Mining Science and Technology
- Vol. 25 (6) , 1017-1021
Study of pre-processing model of coal-mine hoist wire-rope fatigue damage signal
- 3 November 2015
- Published by Elsevier in International Journal of Mining Science and Technology
- Vol. 25 (6) , 1017-1021
Open AccessStudy of pre-processing model of coal-mine hoist wire-rope fatigue damage signal
- Open Access
- 9 July 2015
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 22, 03025
Literature Review of Research on the Technology of Wire Rope Nondestructive Inspection in China and Abroad
As consumables in mine, wire ropes have great significance for safe operation of coal mines. The complex structure makes the nondestructive testing particularly difficult. This paper summarizes the existing methods of analysis at home and abroad from the perspective of strong magnetic and weakly magnetic; introduces the main methods of wire rope at the present, including principle and current status. At last, several critical problems in nondestructive testing of wire rope are discussed.
- 9 July 2015
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 22, 03025
Open AccessLiterature Review of Research on the Technology of Wire Rope Nondestructive Inspection in China and Abroad
As consumables in mine, wire ropes have great significance for safe operation of coal mines. The complex structure makes the nondestructive testing particularly difficult. This paper summarizes the existing methods of analysis at home and abroad from the perspective of strong magnetic and weakly magnetic; introduces the main methods of wire rope at the present, including principle and current status. At last, several critical problems in nondestructive testing of wire rope are discussed.
- 1 July 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 597, 492-497
Research on Overloading Protection of Permanent Magnetic Coupler in Coal Mine
In this paper, with simulations and experiments analysed by the software of Ansoft Maxwell, research on overloading protection of permanent magnetic coupler in coal mine is carried out and the conclusive curves of mechanical characteristics are plotted through experimental data. The conclusion can be gained from mechanical characteristic curves: when the output value of torque reaches the maximum torque of magnetic coupler, the output torque and speed will drop along with increases of the slip, and the input power value of motor is less than the power value at the time when the motor torque value is at the maximum. It explains that the magnetic coupler has the function for overloading protection.
- 1 July 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 597, 492-497
Research on Overloading Protection of Permanent Magnetic Coupler in Coal Mine
In this paper, with simulations and experiments analysed by the software of Ansoft Maxwell, research on overloading protection of permanent magnetic coupler in coal mine is carried out and the conclusive curves of mechanical characteristics are plotted through experimental data. The conclusion can be gained from mechanical characteristic curves: when the output value of torque reaches the maximum torque of magnetic coupler, the output torque and speed will drop along with increases of the slip, and the input power value of motor is less than the power value at the time when the motor torque value is at the maximum. It explains that the magnetic coupler has the function for overloading protection.