Abhay Kumar
Abhay Kumar has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Arun Mahajan
Mahindra & Mahindra, Ltd
3 shared publications- Deepak Sharma
Indian Institute of Technology Guwahati
2 shared publications Dinesh Redkar
Mahindra & Mahindra, Ltd
2 shared publicationsKalyanmoy Deb
Department of Mechanical Engineering, Indian Institute of Technology, Kanpur, India
2 shared publicationsSolairaj Perumal
Mahindra & Mahindra, Ltd
2 shared publicationsAbhirup Chakraborty
Mahindra & Mahindra, Ltd
1 shared publication
Latest Publications
- 9 January 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Method Development to Virtually Validate Farm Tractor Skid for Front End Loader Application
In farm tractors, front end loaders are becoming popular attachments for primarily material handling such as loading, moving and unloading of woodchips, sand, gravels etc. It is also used for some severe load application such as tree uprooting and ripping operation which requires validation of loader frame and tractor as well. To validate the design, a standard pull-push test is carried out on tractor with loader in a laboratory. In this test front loader bucket is pushed against a rigidly clamped fixture with full engine throttle and maximum hydraulic cylinder pressure of loader. To avoid surprise failures during the test, a virtual simulation method needs to be developed and validated.In this paper, a method has been proposed by authors for the above objective. A multi-body dynamics model of tractor with loader is created in MSC ADAMS and actual event is simulated using test loads & boundary conditions. Forces and moments are extracted on all tractor skid attachments points from MBD model. Afterwards, an inertia relief durability analysis is done in MSC Nastran using the extracted loads. Strain gauges are pasted on tractor front axle support, clutch housing and data acquisition activity is carried to extract strain level during test operation. The durability results are correlated with measured strain data and achieved more than 80% correlation.
- 9 January 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Method Development to Virtually Validate Farm Tractor Skid for Front End Loader Application
In farm tractors, front end loaders are becoming popular attachments for primarily material handling such as loading, moving and unloading of woodchips, sand, gravels etc. It is also used for some severe load application such as tree uprooting and ripping operation which requires validation of loader frame and tractor as well. To validate the design, a standard pull-push test is carried out on tractor with loader in a laboratory. In this test front loader bucket is pushed against a rigidly clamped fixture with full engine throttle and maximum hydraulic cylinder pressure of loader. To avoid surprise failures during the test, a virtual simulation method needs to be developed and validated.In this paper, a method has been proposed by authors for the above objective. A multi-body dynamics model of tractor with loader is created in MSC ADAMS and actual event is simulated using test loads & boundary conditions. Forces and moments are extracted on all tractor skid attachments points from MBD model. Afterwards, an inertia relief durability analysis is done in MSC Nastran using the extracted loads. Strain gauges are pasted on tractor front axle support, clutch housing and data acquisition activity is carried to extract strain level during test operation. The durability results are correlated with measured strain data and achieved more than 80% correlation.
- 10 January 2017
- Published by SAE International in SAE International Journal of Commercial Vehicles
- Vol. 10 (1) , 411-422
Field Failure Resolution of a Tractor Engine Exhaust System Using Constrained Single Objective Optimization and Stochastic Analysis
The tractor engine related mounting brackets are very critical due to different aspects of vehicle performance, durability and noise. These mounting bracket have been designed as a framework to support engine external parts like muffler, exhaust tail pipe, alternator etc. Vibration and fatigue has been continuously a concern which may lead to structural failure and performance issues. Various such failures are faced regularly by automotive industry and finite element based analysis are used to resolve them. The resolution is done by playing with the component thicknesses, material, by providing additional support etc. However, due to large degree of uncertainty associated with the loading, boundary conditions, manufacturing, environmental effects; still there is some probability of failure. This paper focuses on a field failure issue of an exhaust system of a tractor and subsequent concern resolution. Multiple field failures like Under Hood Muffler (UHM) lug failure and UHM mounting bracket failure were reported during different tractor applications. A finite element model was generated; static, modal and force frequency response analyses were performed and the field failures were simulated. As there were multiple failure modes, a multi-constrained single objective optimization problem was formulated and an optimum solution was obtained. To start with, few key influencing design parameters were identified, design of experiments (DoE) were conducted, a transfer function was developed and finally an optimum solution was derived. To evaluate the robustness of optimum design under uncertainty of material properties, thicknesses, exhaust temperature; a stochastic analysis were performed to find out the probability of success. No probability of failure was observed for all the objectives.
- 10 January 2017
- Published by SAE International in SAE International Journal of Commercial Vehicles
- Vol. 10 (1) , 411-422
Field Failure Resolution of a Tractor Engine Exhaust System Using Constrained Single Objective Optimization and Stochastic Analysis
The tractor engine related mounting brackets are very critical due to different aspects of vehicle performance, durability and noise. These mounting bracket have been designed as a framework to support engine external parts like muffler, exhaust tail pipe, alternator etc. Vibration and fatigue has been continuously a concern which may lead to structural failure and performance issues. Various such failures are faced regularly by automotive industry and finite element based analysis are used to resolve them. The resolution is done by playing with the component thicknesses, material, by providing additional support etc. However, due to large degree of uncertainty associated with the loading, boundary conditions, manufacturing, environmental effects; still there is some probability of failure. This paper focuses on a field failure issue of an exhaust system of a tractor and subsequent concern resolution. Multiple field failures like Under Hood Muffler (UHM) lug failure and UHM mounting bracket failure were reported during different tractor applications. A finite element model was generated; static, modal and force frequency response analyses were performed and the field failures were simulated. As there were multiple failure modes, a multi-constrained single objective optimization problem was formulated and an optimum solution was obtained. To start with, few key influencing design parameters were identified, design of experiments (DoE) were conducted, a transfer function was developed and finally an optimum solution was derived. To evaluate the robustness of optimum design under uncertainty of material properties, thicknesses, exhaust temperature; a stochastic analysis were performed to find out the probability of success. No probability of failure was observed for all the objectives.
- 10 January 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Durability Analysis Methodology of Tractor Hydraulic Bell Crank Assembly for Various Agricultural Operations
A tractor is vehicle specifically designed to deliver a high tractive effort at slow speeds for carrying out various agriculture operations like ploughing, rotavation etc. using implement. Hydraulic system is a key feature which connects these implements with the tractor. It controls the position and draft of the implement depending upon the type of crop, farming stage, implement type and soil conditions. These variations induces extreme range of load on the hydraulic system, thus making it challenging to design these components. Bell crank assembly is one of the main components of hydraulic system which controls the draft (thus, the loads experienced by tractor) through load sensing mechanism. Often bell crank assembly failures are reported from field due to uneven soil hardness and presence of rocks.This paper studies one of such bell crank assembly failures in the field. The failure was reported after half life cycle of usage during agriculture Operation. Maximum load and fatigue cycle were identified as the main parameters in predicting the failure. Max loads were calculated based on earlier acquired load data and a fatigue duty cycle was prepared to capture the entire range of agricultural operations, implement types, soil types etc. The bell crank assembly was then analyzed for this duty cycle using CAE analysis. A finite element model was prepared and simulation was done in commercially available software with material and boundary nonlinearities. The simulation results were correlated with the experimental results to fine tune the FE model. Once the failure was captured accurately, design iterations were carried out to reduce the cumulative damage within acceptance limit. The final design was tested in lab for the above duty cycle and strain correlation was done with the simulation results. The test was passed successfully with good correlation between the CAE & lab results.
- 10 January 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Durability Analysis Methodology of Tractor Hydraulic Bell Crank Assembly for Various Agricultural Operations
A tractor is vehicle specifically designed to deliver a high tractive effort at slow speeds for carrying out various agriculture operations like ploughing, rotavation etc. using implement. Hydraulic system is a key feature which connects these implements with the tractor. It controls the position and draft of the implement depending upon the type of crop, farming stage, implement type and soil conditions. These variations induces extreme range of load on the hydraulic system, thus making it challenging to design these components. Bell crank assembly is one of the main components of hydraulic system which controls the draft (thus, the loads experienced by tractor) through load sensing mechanism. Often bell crank assembly failures are reported from field due to uneven soil hardness and presence of rocks.This paper studies one of such bell crank assembly failures in the field. The failure was reported after half life cycle of usage during agriculture Operation. Maximum load and fatigue cycle were identified as the main parameters in predicting the failure. Max loads were calculated based on earlier acquired load data and a fatigue duty cycle was prepared to capture the entire range of agricultural operations, implement types, soil types etc. The bell crank assembly was then analyzed for this duty cycle using CAE analysis. A finite element model was prepared and simulation was done in commercially available software with material and boundary nonlinearities. The simulation results were correlated with the experimental results to fine tune the FE model. Once the failure was captured accurately, design iterations were carried out to reduce the cumulative damage within acceptance limit. The final design was tested in lab for the above duty cycle and strain correlation was done with the simulation results. The test was passed successfully with good correlation between the CAE & lab results.
- 14 January 2015
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Agricultural Tractor Cabin Structure Design for Durability and Rollover Protective Structure Test
A cabin on an agricultural tractor is meant to protect the operator from harsh environment, dust and provide an air conditioned space. As it is an enclosed space, cabin structure should be a crashworthiness structure and should not cause serious injury to operator in case of tractor roll over. There are International standard like OECD Code 4, SAE J2194 which regulates the crashworthiness of this protective structure. The roll-over protective structure (ROPS) is characterized by the provision of space for a clearance zone large enough to protect the operator in case of tractor overturn. None of the cabin parts should enter into the clearance zone for operator safety. In addition to meeting ROPS test criteria, the cabin structural strength should be optimized for the required tractor life.In this paper, simulation process has been established to design an agricultural tractor cabin structure and its mountings to meet the above requirements. A Design Verification Plan (DVP) has been developed consisting of 3 load cases. Loads and boundary conditions have been arrived at based on the OECD Code 4 and road & field excitations. Design acceptance criteria have been formulated for clearing the ROPS test and durability for the tractor life. Virtual validation has been done by performing (i) A non-linear elasto-plastic simulation in ABAQUS for ROPS test and (ii) Static & modal analysis in MSC Nastran for durability. For ROPS test, equivalent plastic strain approach has been used for predicting the crack initiation and for durability analysis, fatigue based approach has been used for predicting the life. Lab test has been done for the ROPS test and has been correlated with CAE results. At the end, further design iteration has been done for mass and cost reduction. Biggest challenge in this work was to meet the above criteria within the constraint of material availability and manufacturing limitation.
- 14 January 2015
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Agricultural Tractor Cabin Structure Design for Durability and Rollover Protective Structure Test
A cabin on an agricultural tractor is meant to protect the operator from harsh environment, dust and provide an air conditioned space. As it is an enclosed space, cabin structure should be a crashworthiness structure and should not cause serious injury to operator in case of tractor roll over. There are International standard like OECD Code 4, SAE J2194 which regulates the crashworthiness of this protective structure. The roll-over protective structure (ROPS) is characterized by the provision of space for a clearance zone large enough to protect the operator in case of tractor overturn. None of the cabin parts should enter into the clearance zone for operator safety. In addition to meeting ROPS test criteria, the cabin structural strength should be optimized for the required tractor life.In this paper, simulation process has been established to design an agricultural tractor cabin structure and its mountings to meet the above requirements. A Design Verification Plan (DVP) has been developed consisting of 3 load cases. Loads and boundary conditions have been arrived at based on the OECD Code 4 and road & field excitations. Design acceptance criteria have been formulated for clearing the ROPS test and durability for the tractor life. Virtual validation has been done by performing (i) A non-linear elasto-plastic simulation in ABAQUS for ROPS test and (ii) Static & modal analysis in MSC Nastran for durability. For ROPS test, equivalent plastic strain approach has been used for predicting the crack initiation and for durability analysis, fatigue based approach has been used for predicting the life. Lab test has been done for the ROPS test and has been correlated with CAE results. At the end, further design iteration has been done for mass and cost reduction. Biggest challenge in this work was to meet the above criteria within the constraint of material availability and manufacturing limitation.
- 1 January 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 559, 359-363
Modelling anisotropic hardening of an ultra low carbon high strength steel using crystal plasticity
- 1 January 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 559, 359-363
Modelling anisotropic hardening of an ultra low carbon high strength steel using crystal plasticity
- 1 October 2012
- Published by Elsevier in Computational Materials Science
- Vol. 63, 66-74
Micromechanics based modeling to predict flow behavior and plastic strain localization of dual phase steels
- 1 October 2012
- Published by Elsevier in Computational Materials Science
- Vol. 63, 66-74
Micromechanics based modeling to predict flow behavior and plastic strain localization of dual phase steels
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1089778X,p. 3003-3010
Hybridization of SBX based NSGA-II and sequential quadratic programming for solving multi-objective optimization problems
Most real-world search and optimization problems involve multiple conflicting objectives and results in a Pareto-optimal set. Various multi-objective optimization algorithms have been proposed for solving such problems with the goals of finding as many trade-off solutions as possible and maintaining diversity among them. Since last decade, evolutionary multi-objective optimization (EMO) algorithms have been applied successfully to various test and real-world optimization problems. These population based algorithms provide a diverse set of non-dominated solutions. The obtained non-dominated set is close to the true Pareto-optimal front but it's convergence to the true Pareto-optimal front is not guaranteed. Hence to ensure the same, a local search method using classical algorithm can be applied. In the present work, SBX based NSGA-II is used as a population based approach and the sequential quadratic programming (SQP) method is used as a local search procedure. This hybridization of evolutionary and classical algorithms approach provides a confidence of converging near to the true Pareto-optimal set with a good diversity. The proposed procedure is successfully applied to 13 test problems consisting two, three and five objectives. The obtained results validate our motivation of hybridizing evolutionary and classical methods.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1089778X,p. 3003-3010
Hybridization of SBX based NSGA-II and sequential quadratic programming for solving multi-objective optimization problems
Most real-world search and optimization problems involve multiple conflicting objectives and results in a Pareto-optimal set. Various multi-objective optimization algorithms have been proposed for solving such problems with the goals of finding as many trade-off solutions as possible and maintaining diversity among them. Since last decade, evolutionary multi-objective optimization (EMO) algorithms have been applied successfully to various test and real-world optimization problems. These population based algorithms provide a diverse set of non-dominated solutions. The obtained non-dominated set is close to the true Pareto-optimal front but it's convergence to the true Pareto-optimal front is not guaranteed. Hence to ensure the same, a local search method using classical algorithm can be applied. In the present work, SBX based NSGA-II is used as a population based approach and the sequential quadratic programming (SQP) method is used as a local search procedure. This hybridization of evolutionary and classical algorithms approach provides a confidence of converging near to the true Pareto-optimal set with a good diversity. The proposed procedure is successfully applied to 13 test problems consisting two, three and five objectives. The obtained results validate our motivation of hybridizing evolutionary and classical methods.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1089778X,p. 3011-3018
A hybrid multi-objective optimization procedure using PCX based NSGA-II and sequential quadratic programming
Despite the existence of a number of procedures for multi-objective optimization using evolutionary algorithms, there is still the need for a systematic and unbiased comparison of different approaches on a carefully chosen set of test problems. In this paper, a hybrid approach using PCX based NSGA- II and sequential quadratic programming (SQP) is applied on 19 benchmark test problems consisting of two, three and five objectives. PCX-NSGA-II is used as a population based algorithm where SQP is used as a local search procedure. A population based approach helps in finding the non-dominated set of solutions with a good spread, whereas SQP improves the obtained set of non-dominated solutions locally. The results obtained by the present approach shows mixed performance on the chosen test problems.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1089778X,p. 3011-3018
A hybrid multi-objective optimization procedure using PCX based NSGA-II and sequential quadratic programming
Despite the existence of a number of procedures for multi-objective optimization using evolutionary algorithms, there is still the need for a systematic and unbiased comparison of different approaches on a carefully chosen set of test problems. In this paper, a hybrid approach using PCX based NSGA- II and sequential quadratic programming (SQP) is applied on 19 benchmark test problems consisting of two, three and five objectives. PCX-NSGA-II is used as a population based algorithm where SQP is used as a local search procedure. A population based approach helps in finding the non-dominated set of solutions with a good spread, whereas SQP improves the obtained set of non-dominated solutions locally. The results obtained by the present approach shows mixed performance on the chosen test problems.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1089778X,p. 2125-2132
Light beam search based multi-objective optimization using evolutionary algorithms
For the past decade or so, evolutionary multi-objective optimization (EMO) methodologies have earned wide popularity for solving complex practical optimization problems, simply due to their ability to find a representative set of Pareto-optimal solutions for mostly two, three, and some extent to four and five-objective optimization problems. Recently, emphasis has been made in addressing the decision-making activities in arriving at a single preferred solution. The multiple criteria decision making (MCDM) literature offers a number of possibilities for such a task involving user preferences which can be supplied in different forms. This paper presents an interactive methodology for finding a preferred set of solutions, instead of the complete Pareto-optimal frontier, by incorporating preference information of the decision maker. Particularly, we borrow the concept of light beam search and combine it with the NSGA-II procedure. The working of this procedure has been demonstrated on a set of test problems and on engineering design problems having two to ten objectives, where the obtained solutions are found to match with the true Pareto-optimal solutions. The results highlight the utility of this approach towards eventually facilitating a better and more reliable optimization-cum-decision-making task.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1089778X,p. 2125-2132
Light beam search based multi-objective optimization using evolutionary algorithms
For the past decade or so, evolutionary multi-objective optimization (EMO) methodologies have earned wide popularity for solving complex practical optimization problems, simply due to their ability to find a representative set of Pareto-optimal solutions for mostly two, three, and some extent to four and five-objective optimization problems. Recently, emphasis has been made in addressing the decision-making activities in arriving at a single preferred solution. The multiple criteria decision making (MCDM) literature offers a number of possibilities for such a task involving user preferences which can be supplied in different forms. This paper presents an interactive methodology for finding a preferred set of solutions, instead of the complete Pareto-optimal frontier, by incorporating preference information of the decision maker. Particularly, we borrow the concept of light beam search and combine it with the NSGA-II procedure. The working of this procedure has been demonstrated on a set of test problems and on engineering design problems having two to ten objectives, where the obtained solutions are found to match with the true Pareto-optimal solutions. The results highlight the utility of this approach towards eventually facilitating a better and more reliable optimization-cum-decision-making task.