Xian-Gui Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xian-Gui Zheng has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
K. Lu
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, People's Republic of China
5 shared publicationsY.-N. Shi
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, People's Republic of China
4 shared publications- Jian Hu
Key Laboratory of Transportation Intelligent Operation and Maintenance Technology and Equipment (East China Jiaotong University), Ministry of Education, Nanchang, China
2 shared publications - Yinong Shi
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
2 shared publications - Hai-Jun Jin
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang, China
1 shared publication - Jiongxian Li
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
1 shared publication
Latest Publications
- Open Access
- 4 April 2019
- Published by MDPI AG in Nanomaterials
- Vol. 9 (4) , 546
Achieving Ultrahigh Hardness in Electrodeposited Nanograined Ni-Based Binary Alloys
Annealing hardening has recently been found in nanograined (ng) metals and alloys, which is ascribed to the promotion of grain boundary (GB) stability through GB relaxation and solute atom GB segregation. Annealing hardening is of great significance in extremely fine ng metals since it allows the hardness to keep increasing with a decreasing grain size which would otherwise be softened. Consequently, to synthesize extremely fine ng metals with a stable structure is crucial in achieving an ultrahigh hardness in ng metals. In the present work, direct current electrodeposition was employed to synthesize extremely fine ng Ni-Mo and Ni-P alloys with a grain size of down to a few nanometers. It is demonstrated that the grain size of the as-synthesized extremely fine ng Ni-Mo and Ni-P alloys can be as small as about 3 nm with a homogeneous structure and chemical composition. Grain size strongly depends upon the content of solute atoms (Mo and P). Most importantly, appropriate annealing induces significant hardening as high as 11 GPa in both ng Ni-Mo and Ni-P alloys, while the peak hardening temperature achieved in ng Ni-Mo is much higher than that in ng Ni-P. Electrodeposition is efficient in the synthesis of ultrahard bulk metals or coatings.
- 4 April 2019
- Published by MDPI AG in Nanomaterials
- Vol. 9 (4) , 546
Open AccessAchieving Ultrahigh Hardness in Electrodeposited Nanograined Ni-Based Binary Alloys
Annealing hardening has recently been found in nanograined (ng) metals and alloys, which is ascribed to the promotion of grain boundary (GB) stability through GB relaxation and solute atom GB segregation. Annealing hardening is of great significance in extremely fine ng metals since it allows the hardness to keep increasing with a decreasing grain size which would otherwise be softened. Consequently, to synthesize extremely fine ng metals with a stable structure is crucial in achieving an ultrahigh hardness in ng metals. In the present work, direct current electrodeposition was employed to synthesize extremely fine ng Ni-Mo and Ni-P alloys with a grain size of down to a few nanometers. It is demonstrated that the grain size of the as-synthesized extremely fine ng Ni-Mo and Ni-P alloys can be as small as about 3 nm with a homogeneous structure and chemical composition. Grain size strongly depends upon the content of solute atoms (Mo and P). Most importantly, appropriate annealing induces significant hardening as high as 11 GPa in both ng Ni-Mo and Ni-P alloys, while the peak hardening temperature achieved in ng Ni-Mo is much higher than that in ng Ni-P. Electrodeposition is efficient in the synthesis of ultrahard bulk metals or coatings.
- Open Access
- 7 June 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 165 (9) , C492-C496
Nanoporous Aluminum by Galvanic Replacement: Dealloying and Inward-Growth Plating
In aqueous solutions, electro/chemically deposited metals usually grow outward into electrolyte. Here we report that the reduced Al grows inward into the sample, surprisingly, while Mg (in pure Mg and Al2Mg3 alloy) is galvanically replaced with Al in an ionic liquid. The galvanic replacement reaction (GRR) of Al2Mg3 involves a dealloying process that generates a nanoporous Al skeleton, and simultaneously the inward-growth plating of Al that thickens the Al skeleton. The obtained open nanoporous Al might be interesting for many applications including lithium-ion batteries. The anomalous inward-growth of deposited Al is attributed to the low diffusivity of ionic liquid and the negative charge of reduced species. This dealloying/GRR procedure provides a new route to produce hierarchical nanoporous structure in bulk materials.
- 7 June 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 165 (9) , C492-C496
Open AccessNanoporous Aluminum by Galvanic Replacement: Dealloying and Inward-Growth Plating
In aqueous solutions, electro/chemically deposited metals usually grow outward into electrolyte. Here we report that the reduced Al grows inward into the sample, surprisingly, while Mg (in pure Mg and Al2Mg3 alloy) is galvanically replaced with Al in an ionic liquid. The galvanic replacement reaction (GRR) of Al2Mg3 involves a dealloying process that generates a nanoporous Al skeleton, and simultaneously the inward-growth plating of Al that thickens the Al skeleton. The obtained open nanoporous Al might be interesting for many applications including lithium-ion batteries. The anomalous inward-growth of deposited Al is attributed to the low diffusivity of ionic liquid and the negative charge of reduced species. This dealloying/GRR procedure provides a new route to produce hierarchical nanoporous structure in bulk materials.
- 12 April 2017
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 164 (6) , D348-D353
Effect of a Mixture of Saccharin and 2-Butyne-1,4-diol on Electrodeposition of Nano-Grained Ni-Mo Alloys
Single face centered cubic (fcc) phase nano-grained Ni-Mo alloys were fabricated by electrodeposition in aqueous citrate-ammonia electrolytes with different concentration of sodium molybdate (0.5–7 g/L) with the addition of a mixture of saccharin and 2-butyne-1,4-diol. The effect of the additives mixture on the surface morphology and roughness, composition and grain size of nano-grained Ni-Mo deposits was investigated. It is demonstrated that this additives mixture effectively reduced surface roughness by eliminating bumps and tiny holes. Additionally, the additives mixture significantly reduced the grain size, especially when the concentration of sodium molybdate is low. The minimum grain size achieved with the presence of additives mixture is 4.4 nm with a Mo content of 18.7 at.%. Energy dispersive spectroscopy results indicated that the mixture of additives has little influence on the composition of the derived nano-grained Ni-Mo alloy. Steady state partial polarization together with chronopotentiometry were employed to evaluate the modification of additives to the cathodic process. It is exhibited that electrochemical behavior with the presence of additives correlates well with their effect on composition and grain size of nano-grained Ni-Mo alloys.
- 12 April 2017
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 164 (6) , D348-D353
Effect of a Mixture of Saccharin and 2-Butyne-1,4-diol on Electrodeposition of Nano-Grained Ni-Mo Alloys
Single face centered cubic (fcc) phase nano-grained Ni-Mo alloys were fabricated by electrodeposition in aqueous citrate-ammonia electrolytes with different concentration of sodium molybdate (0.5–7 g/L) with the addition of a mixture of saccharin and 2-butyne-1,4-diol. The effect of the additives mixture on the surface morphology and roughness, composition and grain size of nano-grained Ni-Mo deposits was investigated. It is demonstrated that this additives mixture effectively reduced surface roughness by eliminating bumps and tiny holes. Additionally, the additives mixture significantly reduced the grain size, especially when the concentration of sodium molybdate is low. The minimum grain size achieved with the presence of additives mixture is 4.4 nm with a Mo content of 18.7 at.%. Energy dispersive spectroscopy results indicated that the mixture of additives has little influence on the composition of the derived nano-grained Ni-Mo alloy. Steady state partial polarization together with chronopotentiometry were employed to evaluate the modification of additives to the cathodic process. It is exhibited that electrochemical behavior with the presence of additives correlates well with their effect on composition and grain size of nano-grained Ni-Mo alloys.
- 13 May 2016
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 163 (8) , D349-D354
The Combination Addition of 2-Mercapto-5-benzimidazolesulfonic Acid and Thiourea to Watts Bath in Controllable Electro-Healing Cracks in Nickel
Based upon previous investigations on crack electro-healing by the addition of only inhibitor(s), the present paper concentrates on the exploration of the crack electro-healing behavior in pure Ni with the combination presence of an inhibitor 2-Mercapto-5-benzimidazolesulfonic acid (MBIS) and an accelerator thiourea (TU) in Watts bath. Voltammetry was performed to characterize the electrochemical aspect when these two additives were added. Current transient and injection experiments were conducted to study the synergistic effect of MBIS and TU to Ni deposition. It is proposed that TU will displace some of the MBIS molecules adsorbed on the electrode surface, which will break up the blocking layer of MBIS, therefore avoid the formation of annual-ring-like defects that form when only MBIS is present.
- 13 May 2016
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 163 (8) , D349-D354
The Combination Addition of 2-Mercapto-5-benzimidazolesulfonic Acid and Thiourea to Watts Bath in Controllable Electro-Healing Cracks in Nickel
Based upon previous investigations on crack electro-healing by the addition of only inhibitor(s), the present paper concentrates on the exploration of the crack electro-healing behavior in pure Ni with the combination presence of an inhibitor 2-Mercapto-5-benzimidazolesulfonic acid (MBIS) and an accelerator thiourea (TU) in Watts bath. Voltammetry was performed to characterize the electrochemical aspect when these two additives were added. Current transient and injection experiments were conducted to study the synergistic effect of MBIS and TU to Ni deposition. It is proposed that TU will displace some of the MBIS molecules adsorbed on the electrode surface, which will break up the blocking layer of MBIS, therefore avoid the formation of annual-ring-like defects that form when only MBIS is present.
- 1 November 2015
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 31 (11) , 1151-1157
Healing Process of Casting Pores in a Ni-based Superalloy by Hot Isostatic Pressing
- 1 November 2015
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 31 (11) , 1151-1157
Healing Process of Casting Pores in a Ni-based Superalloy by Hot Isostatic Pressing
- 27 February 2015
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 162 (6) , D222-D228
Evaluating the Performance of 2-Mercapto-5-Benzimidazolesulfonic Acid in Controllable Electro-Healing Cracks in Nickel
The performance of 2-Mercapto-5-benzimidazolesulfonic acid (MBIS) in a Watts bath in crack electro-healing was investigated. Potentiostatic and galvanostatic voltammetry, current efficiency measurements were performed for electrochemical investigation. The morphology of the healed crack indicates that the healing crystals grow in a controllable manner with the addition of MBIS under forced convection with the healing crystals fill preferentially in the crack tip to the crack sidewalls. No obvious defects were observed along the interface between the substrate and the healing crystals, which is attributed the much higher current efficiency of MBIS. Annual-ring like defects are observed but with a much longer width compared with PEI. The formation mechanism of annual ring is discussed. Possible approach to get defect-free crack healing is also prospected.
- 27 February 2015
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 162 (6) , D222-D228
Evaluating the Performance of 2-Mercapto-5-Benzimidazolesulfonic Acid in Controllable Electro-Healing Cracks in Nickel
The performance of 2-Mercapto-5-benzimidazolesulfonic acid (MBIS) in a Watts bath in crack electro-healing was investigated. Potentiostatic and galvanostatic voltammetry, current efficiency measurements were performed for electrochemical investigation. The morphology of the healed crack indicates that the healing crystals grow in a controllable manner with the addition of MBIS under forced convection with the healing crystals fill preferentially in the crack tip to the crack sidewalls. No obvious defects were observed along the interface between the substrate and the healing crystals, which is attributed the much higher current efficiency of MBIS. Annual-ring like defects are observed but with a much longer width compared with PEI. The formation mechanism of annual ring is discussed. Possible approach to get defect-free crack healing is also prospected.
- 29 September 2014
- Published by The Electrochemical Society in ECS Transactions
- Vol. 61 (28) , 1-9
An Electrochemical Investigation on Additives to the Controllable Electro-Healing Cracks in Nickel
In the present work, polyethyleneimine (PEI), 2-mercapto-5-benzimidazolesulfonic acid (MBIS), MBIS and thiourea (TU) were added respectively to the conventional Watts bath to investigate the controllable electro-healing on pure Ni plate with a through thickness crack. It is demonstrated that PEI has a strong inhibition effect on the Ni reduction, which resulted in the formation of large visible defects along the interface between the substrate and the healing crystals. MBIS has a similar inhibition effect on Ni reduction, but with a promoted current efficiency. The addition of TU to the MBIS added solution depolarized the Ni reduction, resulting in an enhanced growth of healing crystals from sidewalls of the crack.
- 29 September 2014
- Published by The Electrochemical Society in ECS Transactions
- Vol. 61 (28) , 1-9
An Electrochemical Investigation on Additives to the Controllable Electro-Healing Cracks in Nickel
In the present work, polyethyleneimine (PEI), 2-mercapto-5-benzimidazolesulfonic acid (MBIS), MBIS and thiourea (TU) were added respectively to the conventional Watts bath to investigate the controllable electro-healing on pure Ni plate with a through thickness crack. It is demonstrated that PEI has a strong inhibition effect on the Ni reduction, which resulted in the formation of large visible defects along the interface between the substrate and the healing crystals. MBIS has a similar inhibition effect on Ni reduction, but with a promoted current efficiency. The addition of TU to the MBIS added solution depolarized the Ni reduction, resulting in an enhanced growth of healing crystals from sidewalls of the crack.
- 4 April 2013
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 160 (6) , D289-D293
An Investigation on Polyethyleneimine and Saccharin on Controllable Electro-Healing Cracks in Nickel
To minimize pores or voids that left after electro-healing by plain solution without additives, controllable electro-healing was investigated in pure Ni plates with a through-thickness crack in a Watts bath by adding polyethyleneimine (PEI) and saccharin. Controllable electro-healing means that the growth velocity of healing crystals from crack tips is much faster than that from sidewalls of the crack, which reduces the number of pores owing to depletion of healing solution. Rotating disk electrode (RDE) was introduced to evaluate the electrochemical behavior in crack tips and crack center. Voltammograms and galvanostatic measurements indicated that PEI exhibits a convection-dependent inhibition effect on Ni deposition. The addition of saccharin will much enhance the inhibition behavior of PEI, controllable electro-healing was achieved with the presence of both PEI and saccharin.
- 4 April 2013
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 160 (6) , D289-D293
An Investigation on Polyethyleneimine and Saccharin on Controllable Electro-Healing Cracks in Nickel
To minimize pores or voids that left after electro-healing by plain solution without additives, controllable electro-healing was investigated in pure Ni plates with a through-thickness crack in a Watts bath by adding polyethyleneimine (PEI) and saccharin. Controllable electro-healing means that the growth velocity of healing crystals from crack tips is much faster than that from sidewalls of the crack, which reduces the number of pores owing to depletion of healing solution. Rotating disk electrode (RDE) was introduced to evaluate the electrochemical behavior in crack tips and crack center. Voltammograms and galvanostatic measurements indicated that PEI exhibits a convection-dependent inhibition effect on Ni deposition. The addition of saccharin will much enhance the inhibition behavior of PEI, controllable electro-healing was achieved with the presence of both PEI and saccharin.
- 1 January 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 561, 52-59
Electro-healing cracks in nickel
- 1 January 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 561, 52-59
Electro-healing cracks in nickel