Qiang Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Qiang Wang has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Xin Che
School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan, People’s Republic of China
3 shared publicationsZhimin Zhang
College of Materials Science and Engineering, North University of China, Taiyuan, People’s Republic of China
3 shared publications- Zhimin Zhang
School of Materials Science and Engineering, North University of China, Taiyuan 030051, China
3 shared publications - Beibei Dong
College of Materials Science and Engineering, North University of China, Taiyuan 030051, China
2 shared publications - Fulai Yang
College of Materials Science and Engineering, North University of China, Taiyuan 030051, China
2 shared publications Guanshi Zhang
School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan, People’s Republic of China
2 shared publications
Latest Publications
- Open Access
Deformation Behavior and Microstructural Evolution Coordinated Regulation by Compression Deformation for Metastable Ti Alloy
In this paper, in order to investigate the harmonious relationship between the compression deformation behavior of metastable β titanium alloy and the microstructure evolution, the β solution-treated Ti-10V-2Fe-3Al (Ti-1023) alloy was compressed at room temperature and its deformation behavior was analyzed. Optical microscopy (OM) and field emission electron microscopy (FESEM) were used to study the microstructure evolution of alloys at different strain rates. The results show that the stress-induced martensite transformation (SIMT) is more easily activated by low strain rate compression deformation, which is conducive to improving its comprehensive mechanical properties. With the decrease in strain rate, the α″ martensite content increases significantly, the average grain size decreases substantially, and the Low Angle Grain Boundary (LAGB) volume fraction decreases correspondingly. In addition, after compression at different strain rates, the misorientation angle (MA) of the β matrix is mainly concentrated in the LAGBs. The change is small with the decrease in strain rate, but the α″ martensite orientation difference angle shows some peaks, which are ~60°, ~85°, and ~95°, respectively. Simultaneously, the strain rate has an important effect on the content and type of martensitic twins. Finally, the fracture morphology analysis shows that with the increase in strain rate, the fracture mode changes from ductile fracture to brittle fracture. The fracture surface presents a significantly elongated cavity along the direction of maximum shear stress.
Open AccessDeformation Behavior and Microstructural Evolution Coordinated Regulation by Compression Deformation for Metastable Ti Alloy
In this paper, in order to investigate the harmonious relationship between the compression deformation behavior of metastable β titanium alloy and the microstructure evolution, the β solution-treated Ti-10V-2Fe-3Al (Ti-1023) alloy was compressed at room temperature and its deformation behavior was analyzed. Optical microscopy (OM) and field emission electron microscopy (FESEM) were used to study the microstructure evolution of alloys at different strain rates. The results show that the stress-induced martensite transformation (SIMT) is more easily activated by low strain rate compression deformation, which is conducive to improving its comprehensive mechanical properties. With the decrease in strain rate, the α″ martensite content increases significantly, the average grain size decreases substantially, and the Low Angle Grain Boundary (LAGB) volume fraction decreases correspondingly. In addition, after compression at different strain rates, the misorientation angle (MA) of the β matrix is mainly concentrated in the LAGBs. The change is small with the decrease in strain rate, but the α″ martensite orientation difference angle shows some peaks, which are ~60°, ~85°, and ~95°, respectively. Simultaneously, the strain rate has an important effect on the content and type of martensitic twins. Finally, the fracture morphology analysis shows that with the increase in strain rate, the fracture mode changes from ductile fracture to brittle fracture. The fracture surface presents a significantly elongated cavity along the direction of maximum shear stress.
- 1 June 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 133 (3-4) , 1-17
A novel combined extrusion process of thin-walled tubular part with protrusion
- 1 June 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 133 (3-4) , 1-17
A novel combined extrusion process of thin-walled tubular part with protrusion
- 12 May 2023
- Published by Springer Nature in Metals and Materials International
- Vol. 29 (11) , 3273-3285
Effect of Temperature and Revolution on the Microstructure, Texture and Microhardness of the AZ80 Alloy Cup Prepared by Rotating Backward Extrusion
- 12 May 2023
- Published by Springer Nature in Metals and Materials International
- Vol. 29 (11) , 3273-3285
Effect of Temperature and Revolution on the Microstructure, Texture and Microhardness of the AZ80 Alloy Cup Prepared by Rotating Backward Extrusion
- Open Access
- 11 April 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 24, 4711-4729
Evolution of microstructure, texture and mechanical properties of AZ80 Mg alloy tubular produced by rotating backward extrusion with modified open punch
- 11 April 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 24, 4711-4729
Open AccessEvolution of microstructure, texture and mechanical properties of AZ80 Mg alloy tubular produced by rotating backward extrusion with modified open punch
- Open Access
- 1 February 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (2) , 026508
Study on anisotropic behavior of 7075 Al alloy after extrusion
For an extrusion process of 7075 Al alloy, the extrusion direction of the initial blank is changed to study the mechanical properties of the formed plates and characterize their microstructure. The as-received bar is extruded 7075 Al alloy. The secondary extrusion deformation is along and perpendicular to the initial extrusion direction. The results show that the anisotropy of mechanical properties of the two samples decreases obviously after secondary deformation. The anisotropy of yield strength and ultimate tensile strength of ED90 sample is lower than that of ED0 sample, but the plastic anisotropy is slightly higher than that of ED0 sample. In addition, the recrystallized grain proportion of ED90 sample is high and the texture strength is low, so the Schmid factor in the three directions is similar. The tensile fracture mode of the two samples belongs to ductile fracture, but the morphology of dimple and the size of cleavage plane are slightly different.
- 1 February 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (2) , 026508
Open AccessStudy on anisotropic behavior of 7075 Al alloy after extrusion
For an extrusion process of 7075 Al alloy, the extrusion direction of the initial blank is changed to study the mechanical properties of the formed plates and characterize their microstructure. The as-received bar is extruded 7075 Al alloy. The secondary extrusion deformation is along and perpendicular to the initial extrusion direction. The results show that the anisotropy of mechanical properties of the two samples decreases obviously after secondary deformation. The anisotropy of yield strength and ultimate tensile strength of ED90 sample is lower than that of ED0 sample, but the plastic anisotropy is slightly higher than that of ED0 sample. In addition, the recrystallized grain proportion of ED90 sample is high and the texture strength is low, so the Schmid factor in the three directions is similar. The tensile fracture mode of the two samples belongs to ductile fracture, but the morphology of dimple and the size of cleavage plane are slightly different.
- Open Access
Anisotropic Low Cycle Behavior of the Extruded 7075 Al Alloy
The quasi-static and low cycle fatigue tests of extruded 7075 Al alloy (Φ200 mm) were investigated in three directions: the extrusion direction (ED), the radial direction (RD), and 45° with ED (45°). Grain morphology analysis, texture measurement, and fatigue fracture characterization were conducted to discuss the relationship between microstructure and mechanical properties. The experimental results showed that the ED specimen had higher ultimate tensile strength (UTS) and low cycle fatigue (LCF) properties, which were mainly attributed to the following three causes. First, the grain boundaries (GBs) had an obvious effect on the crack growth. The number of GBs in the three directions was different due to the shape of the grains elongated along the ED. Second, the sharp texture and the small Schmidt factor along the ED explained the higher ultimate tensile strength (UTS) of the ED specimens. Third, fatigue fracture observation showed that the ED specimen had a narrow fatigue striation spacing, which indicated that the plastic deformation of the ED specimen was the smallest in each cycle. In addition, two fatigue prediction models were established to predict the LCF life of extruded 7075 Al alloy, based on the life response behavior of the three directions under different strains.
Open AccessAnisotropic Low Cycle Behavior of the Extruded 7075 Al Alloy
The quasi-static and low cycle fatigue tests of extruded 7075 Al alloy (Φ200 mm) were investigated in three directions: the extrusion direction (ED), the radial direction (RD), and 45° with ED (45°). Grain morphology analysis, texture measurement, and fatigue fracture characterization were conducted to discuss the relationship between microstructure and mechanical properties. The experimental results showed that the ED specimen had higher ultimate tensile strength (UTS) and low cycle fatigue (LCF) properties, which were mainly attributed to the following three causes. First, the grain boundaries (GBs) had an obvious effect on the crack growth. The number of GBs in the three directions was different due to the shape of the grains elongated along the ED. Second, the sharp texture and the small Schmidt factor along the ED explained the higher ultimate tensile strength (UTS) of the ED specimens. Third, fatigue fracture observation showed that the ED specimen had a narrow fatigue striation spacing, which indicated that the plastic deformation of the ED specimen was the smallest in each cycle. In addition, two fatigue prediction models were established to predict the LCF life of extruded 7075 Al alloy, based on the life response behavior of the three directions under different strains.
- 11 July 2021
- Published by Springer Nature
- p. 1055-1062
Investigation of Forward–Backward–Radial Extrusion Process of Aluminum Alloy Wheel Hub
- 11 July 2021
- Published by Springer Nature
- p. 1055-1062
Investigation of Forward–Backward–Radial Extrusion Process of Aluminum Alloy Wheel Hub
- Open Access
- 1 December 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (12) , 126518
Influence of a novel SPD technique together with heat treatment on the microstructural characteristics and hardness of Mg-13Gd-4Y-2Zn-0.5Zr alloys
In this study, Mg-13Gd-4Y-2Zn-0.5Zr alloys were fabricated and subjected to 3 passes of cyclic expansion-extrusion with an asymmetrical cavity (CEE-AEC). The influence of the CEE-AEC together with the heat treatment on the microstructural characteristics and hardness were investigated systematically, through optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Vickers hardness testing machine. The results illuminated that the introduction of the strains through CEE-AEC has a significant effect on the heat treatment of the specimens. The precipitation of the second phases particles was remarkably accelerated, including the lamellar phases in solution treatment, the grain boundary precipitates and the equilibrium β phases in ageing treatment. Likewise, the hardness of the investigated samples was obviously improved by the comprehensive effect of the CEE-AEC together with the heat treatment, and the peak aging time of the CEE-AEC samples was substantially advanced relative to the as-cast ones. The enhanced hardness owned relatively high thermal stability in the ambient temperature. The precipitation sequence of 3 CEE-AEC passes alloy aged at 225 °C was as follows: supersaturated solid solution Mg (S.S.S.S)→β″ (DO19)→β′ (bco)→β 1 (fcc)→β (fcc).
- 1 December 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (12) , 126518
Open AccessInfluence of a novel SPD technique together with heat treatment on the microstructural characteristics and hardness of Mg-13Gd-4Y-2Zn-0.5Zr alloys
In this study, Mg-13Gd-4Y-2Zn-0.5Zr alloys were fabricated and subjected to 3 passes of cyclic expansion-extrusion with an asymmetrical cavity (CEE-AEC). The influence of the CEE-AEC together with the heat treatment on the microstructural characteristics and hardness were investigated systematically, through optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Vickers hardness testing machine. The results illuminated that the introduction of the strains through CEE-AEC has a significant effect on the heat treatment of the specimens. The precipitation of the second phases particles was remarkably accelerated, including the lamellar phases in solution treatment, the grain boundary precipitates and the equilibrium β phases in ageing treatment. Likewise, the hardness of the investigated samples was obviously improved by the comprehensive effect of the CEE-AEC together with the heat treatment, and the peak aging time of the CEE-AEC samples was substantially advanced relative to the as-cast ones. The enhanced hardness owned relatively high thermal stability in the ambient temperature. The precipitation sequence of 3 CEE-AEC passes alloy aged at 225 °C was as follows: supersaturated solid solution Mg (S.S.S.S)→β″ (DO19)→β′ (bco)→β 1 (fcc)→β (fcc).
- Open Access
An Investigation on the Microstructure and Texture of an AZ80 Cup-Shaped Piece Processed by Rotating Backward Extrusion
The rotating backward extrusion (RBE) process, as a new severe plastic deformation (SPD) process, is based on conventional backward extrusion and rotation, which meets the requirement of modern industrial development with its high performance and production efficiency. However, there is little research on the microstructure evolution and texture modification of the RBE process. Thus, in this study, the effect of different rotating revolutions, e.g., n = 5, n = 10, and n = 50, on the microstructure and texture development for the RBE process based on the AZ80 magnesium (Mg) alloy were investigated at 653 K. The results disclose that the rotating revolution is an influencing processing parameter on the deformation of the RBE process. The grain refining ability is enhanced with the increase of the rotating revolutions, and the minimum grain size of the cup bottom, shearing zone, and cup wall can reach to 16.7 μm, 15.6 μm, and 13.0 μm, respectively, under the condition of n = 50. Furthermore, with the increase in the rotating revolutions, the microstructure of the alloy becomes more uniform and the proportion of dynamic recrystallization (DRX) is also increased. The maximum DRX fractions of the sample for the cup bottom and cup wall are 95.4% and 86.8%, respectively, at n = 50. The DRX mechanism of the RBE process is determined by the continuous DRX and discontinuous DRX. In addition, the texture can be significant weakened during the RBE process, especially at the cup bottom, where the maximum pole intensity can be reduced from 17.6 at n = 10 to 6.5 at n = 50, which can be attributed to the higher proportion of new DRXed grains whose orientations are more random compared with the deformed grains.
Open AccessAn Investigation on the Microstructure and Texture of an AZ80 Cup-Shaped Piece Processed by Rotating Backward Extrusion
The rotating backward extrusion (RBE) process, as a new severe plastic deformation (SPD) process, is based on conventional backward extrusion and rotation, which meets the requirement of modern industrial development with its high performance and production efficiency. However, there is little research on the microstructure evolution and texture modification of the RBE process. Thus, in this study, the effect of different rotating revolutions, e.g., n = 5, n = 10, and n = 50, on the microstructure and texture development for the RBE process based on the AZ80 magnesium (Mg) alloy were investigated at 653 K. The results disclose that the rotating revolution is an influencing processing parameter on the deformation of the RBE process. The grain refining ability is enhanced with the increase of the rotating revolutions, and the minimum grain size of the cup bottom, shearing zone, and cup wall can reach to 16.7 μm, 15.6 μm, and 13.0 μm, respectively, under the condition of n = 50. Furthermore, with the increase in the rotating revolutions, the microstructure of the alloy becomes more uniform and the proportion of dynamic recrystallization (DRX) is also increased. The maximum DRX fractions of the sample for the cup bottom and cup wall are 95.4% and 86.8%, respectively, at n = 50. The DRX mechanism of the RBE process is determined by the continuous DRX and discontinuous DRX. In addition, the texture can be significant weakened during the RBE process, especially at the cup bottom, where the maximum pole intensity can be reduced from 17.6 at n = 10 to 6.5 at n = 50, which can be attributed to the higher proportion of new DRXed grains whose orientations are more random compared with the deformed grains.
- 9 January 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 26 (12) , 1786-1796
Numerical and Experimental Analysis of Rotating Backward Extrusion as a New SPD Process
- 9 January 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 26 (12) , 1786-1796
Numerical and Experimental Analysis of Rotating Backward Extrusion as a New SPD Process