Robert Gerlach
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Robert Gerlach has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Nik Petrinic
Department of Engineering Science, University of Oxford, Oxford, UK
6 shared publications Clive R. Siviour
Department of Engineering Science, Impact Engineering Laboratory , University of Oxford , Oxford , UK
4 shared publicationsJens Wiegand
Department of Engineering Science, Impact Engineering Laboratory , University of Oxford , Oxford , UK
4 shared publications- Andreas Hornig
Technische Universität Dresden
2 shared publications N. Petrinic
2 shared publications- Werner Hufenbach
Institute of Lightweight Engineering and Polymer Technology (ILK) Technische Universität Dresden Holbeinstraße 3 01307 Dresden Germany
2 shared publications
Latest Publications
- 1 January 2015
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 75, 214-221
The mechanical response of a syntactic polyurethane foam at low and high rates of strain
- 1 January 2015
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 75, 214-221
The mechanical response of a syntactic polyurethane foam at low and high rates of strain
- 23 December 2014
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 22 (5) , 413-421
An Experimental Method for Dynamic Delamination Analysis of Composite Materials by Impact Bending
An improved experimental method for characterizing dynamic delamination growth in composite structures has been developed and verified using high speed photography and explicit finite element simulation. The method is based on a three-point bending device. End notch flexure carbon fiber composite beam specimens were subjected to both quasi-static and impact rates of Mode II loading. The experimental results showed no significant strain rate dependency of the delamination fracture toughness. This important result complements the scarce and conflicting data available in the literature, and serves as a reference for calibration of numerical modeling strategies.
- 23 December 2014
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 22 (5) , 413-421
An Experimental Method for Dynamic Delamination Analysis of Composite Materials by Impact Bending
An improved experimental method for characterizing dynamic delamination growth in composite structures has been developed and verified using high speed photography and explicit finite element simulation. The method is based on a three-point bending device. End notch flexure carbon fiber composite beam specimens were subjected to both quasi-static and impact rates of Mode II loading. The experimental results showed no significant strain rate dependency of the delamination fracture toughness. This important result complements the scarce and conflicting data available in the literature, and serves as a reference for calibration of numerical modeling strategies.
- 9 August 2013
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 20 (7) , 505-514
The Strain Rate Dependent Material Behavior of S-GFRP Extracted from GLARE
S-Glass fiber reinforced epoxy (S-GFRP) extracted from GLARE has been experimentally characterized at three distinct strain-rates (5 × 10−4 s−1, 10 s−1, and c.a. 2000 s−1) and in four loading directions (0°, 90°, and 45° to the fiber direction and in the through-thickness direction). A novel specimen clamping mechanism was developed and full-field optical strain measurement was applied. With the aid of these techniques, a significant increase in failure-strength and apparent elastic modulus in all loading directions, particularly in fiber direction, was observed with an increased strain-rate; strain to failure increased in the fiber direction and decreased in all other loading directions.
- 9 August 2013
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 20 (7) , 505-514
The Strain Rate Dependent Material Behavior of S-GFRP Extracted from GLARE
S-Glass fiber reinforced epoxy (S-GFRP) extracted from GLARE has been experimentally characterized at three distinct strain-rates (5 × 10−4 s−1, 10 s−1, and c.a. 2000 s−1) and in four loading directions (0°, 90°, and 45° to the fiber direction and in the through-thickness direction). A novel specimen clamping mechanism was developed and full-field optical strain measurement was applied. With the aid of these techniques, a significant increase in failure-strength and apparent elastic modulus in all loading directions, particularly in fiber direction, was observed with an increased strain-rate; strain to failure increased in the fiber direction and decreased in all other loading directions.
- 1 December 2012
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 50, 63-67
A new split Hopkinson tensile bar design
- 1 December 2012
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 50, 63-67
A new split Hopkinson tensile bar design
- 1 February 2012
- Published by Elsevier in Composites Science and Technology
- Vol. 72 (3) , 397-411
In-plane and through-thickness properties, failure modes, damage and delamination in 3D woven carbon fibre composites subjected to impact loading
- 1 February 2012
- Published by Elsevier in Composites Science and Technology
- Vol. 72 (3) , 397-411
In-plane and through-thickness properties, failure modes, damage and delamination in 3D woven carbon fibre composites subjected to impact loading
- 1 December 2011
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 38 (12) , 976-980
A novel method for pulse shaping of Split Hopkinson tensile bar signals
- 1 December 2011
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 38 (12) , 976-980
A novel method for pulse shaping of Split Hopkinson tensile bar signals
- 1 September 2009
- Published by Elsevier in Composites Science and Technology
- Vol. 69 (11-12) , 2024-2026
The interface between matrix pockets and fibre bundles under impact loading
- 1 September 2009
- Published by Elsevier in Composites Science and Technology
- Vol. 69 (11-12) , 2024-2026
The interface between matrix pockets and fibre bundles under impact loading