Zhimin Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhimin Zhang has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Beibei Dong
College of Materials Science and Engineering, North University of China, Taiyuan 030051, China
4 shared publications Beibei Dong
3 shared publicationsMu Meng
3 shared publications- Fulai Yang
College of Materials Science and Engineering, North University of China, Taiyuan 030051, China
2 shared publications Jianmin Yu
2 shared publications- Jin Ma
College of Materials Science and Engineering, North University of China, 3 Xueyuan Road, Taiyuan 030051, China
2 shared publications
Latest Publications
- Open Access
Hot Deformation Behavior and Processing Map Considering Strengthening Effect for Al–10.0Zn–3.0Mg–2.8Cu Alloy
In this paper, a hot processing map that takes into the strengthening effect into account is optimized for the Al–10.0Zn–3.0Mg–2.8Cu alloy, mainly considering the crushing and dissolving behavior of the insoluble phase. The hot deformation experiments were performed by compression testing with strain rates ranging from 0.001 to 1 s−1 and the temperature ranging from 380 to 460 °C. The hot processing map was established at the strain of 0.9. It exhibits that the appropriate hot processing region is located at the temperature from 431 to 456 °C and its strain rate is within 0.004–0.108 s−1. The recrystallization mechanisms and insoluble phase evolution were demonstrated using the real-time EBSD-EDS detection technology for this alloy. It is verified that the work hardening can also be consumed by the coarse insoluble phase refinement with the strain rate increasing from 0.001 to 0.1 s−1, besides the traditional recovery and recrystallization, but the effect of the insoluble phase crushing was weakened when strain rate increased over 0.1 s−1. Better refinement of the insoluble phase was around strain rate in 0.1 s−1, which exhibits adequate dissolving during the solid solution treatment, leading to excellent aging strengthen effects. Finally, the hot processing region was further optimized, so that the strain rate approaches 0.1 s−1 instead of 0.004–0.108 s−1. This will provide a theoretical support for the subsequent deformation of the Al–10.0Zn–3.0Mg–2.8Cu alloy and its’ engineering application in aerospace, defense and military fields.
Open AccessHot Deformation Behavior and Processing Map Considering Strengthening Effect for Al–10.0Zn–3.0Mg–2.8Cu Alloy
In this paper, a hot processing map that takes into the strengthening effect into account is optimized for the Al–10.0Zn–3.0Mg–2.8Cu alloy, mainly considering the crushing and dissolving behavior of the insoluble phase. The hot deformation experiments were performed by compression testing with strain rates ranging from 0.001 to 1 s−1 and the temperature ranging from 380 to 460 °C. The hot processing map was established at the strain of 0.9. It exhibits that the appropriate hot processing region is located at the temperature from 431 to 456 °C and its strain rate is within 0.004–0.108 s−1. The recrystallization mechanisms and insoluble phase evolution were demonstrated using the real-time EBSD-EDS detection technology for this alloy. It is verified that the work hardening can also be consumed by the coarse insoluble phase refinement with the strain rate increasing from 0.001 to 0.1 s−1, besides the traditional recovery and recrystallization, but the effect of the insoluble phase crushing was weakened when strain rate increased over 0.1 s−1. Better refinement of the insoluble phase was around strain rate in 0.1 s−1, which exhibits adequate dissolving during the solid solution treatment, leading to excellent aging strengthen effects. Finally, the hot processing region was further optimized, so that the strain rate approaches 0.1 s−1 instead of 0.004–0.108 s−1. This will provide a theoretical support for the subsequent deformation of the Al–10.0Zn–3.0Mg–2.8Cu alloy and its’ engineering application in aerospace, defense and military fields.
- Open Access
- 1 February 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (2) , 026508
Study on anisotropic behavior of 7075 Al alloy after extrusion
For an extrusion process of 7075 Al alloy, the extrusion direction of the initial blank is changed to study the mechanical properties of the formed plates and characterize their microstructure. The as-received bar is extruded 7075 Al alloy. The secondary extrusion deformation is along and perpendicular to the initial extrusion direction. The results show that the anisotropy of mechanical properties of the two samples decreases obviously after secondary deformation. The anisotropy of yield strength and ultimate tensile strength of ED90 sample is lower than that of ED0 sample, but the plastic anisotropy is slightly higher than that of ED0 sample. In addition, the recrystallized grain proportion of ED90 sample is high and the texture strength is low, so the Schmid factor in the three directions is similar. The tensile fracture mode of the two samples belongs to ductile fracture, but the morphology of dimple and the size of cleavage plane are slightly different.
- 1 February 2022
- Published by IOP Publishing in Materials Research Express
- Vol. 9 (2) , 026508
Open AccessStudy on anisotropic behavior of 7075 Al alloy after extrusion
For an extrusion process of 7075 Al alloy, the extrusion direction of the initial blank is changed to study the mechanical properties of the formed plates and characterize their microstructure. The as-received bar is extruded 7075 Al alloy. The secondary extrusion deformation is along and perpendicular to the initial extrusion direction. The results show that the anisotropy of mechanical properties of the two samples decreases obviously after secondary deformation. The anisotropy of yield strength and ultimate tensile strength of ED90 sample is lower than that of ED0 sample, but the plastic anisotropy is slightly higher than that of ED0 sample. In addition, the recrystallized grain proportion of ED90 sample is high and the texture strength is low, so the Schmid factor in the three directions is similar. The tensile fracture mode of the two samples belongs to ductile fracture, but the morphology of dimple and the size of cleavage plane are slightly different.
- Open Access
Microstructure Evolution and Dynamic Recrystallization Behavior of Mg-Gd-Y-Zn-Zr Alloy during Rotating Backward Extrusion
Rotating backward extrusion (RBE) is one of severe plastic deformation (SPD) methods used to produce cylindrical components with a very large strain by a single pass. In this study, the microstructure and texture evolution in the different regions of Mg-12Gd-4Y-2Zn-0.5Zr (wt.%) alloys via RBE process were investigated by using optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM) and electron back-scatter diffraction (EBSD). The results showed that the cup-shaped sample formed by RBE process exhibited typical gradient microstructure expanding from its inner wall to outer wall along the radial direction (RD). The average grain size of the RBEed sample decreased when the radius decreased from the edge region to the center region along the RD, which was attributed to the different strains and strain rates in the different regions. It also could be observed that the center region showed highest deformation and the edge region exhibited the lowest deformation in the RBEed sample along the RD. In addition, the grain refinement mechanisms of the experimental alloy containing long-period stacking ordered (LPSO) phases after RBE with 100 N were continuous dynamic recrystallization (CDRX), discontinuous dynamic recrystallization (DDRX) and particle stimulated nucleation (PSN).
Open AccessMicrostructure Evolution and Dynamic Recrystallization Behavior of Mg-Gd-Y-Zn-Zr Alloy during Rotating Backward Extrusion
Rotating backward extrusion (RBE) is one of severe plastic deformation (SPD) methods used to produce cylindrical components with a very large strain by a single pass. In this study, the microstructure and texture evolution in the different regions of Mg-12Gd-4Y-2Zn-0.5Zr (wt.%) alloys via RBE process were investigated by using optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM) and electron back-scatter diffraction (EBSD). The results showed that the cup-shaped sample formed by RBE process exhibited typical gradient microstructure expanding from its inner wall to outer wall along the radial direction (RD). The average grain size of the RBEed sample decreased when the radius decreased from the edge region to the center region along the RD, which was attributed to the different strains and strain rates in the different regions. It also could be observed that the center region showed highest deformation and the edge region exhibited the lowest deformation in the RBEed sample along the RD. In addition, the grain refinement mechanisms of the experimental alloy containing long-period stacking ordered (LPSO) phases after RBE with 100 N were continuous dynamic recrystallization (CDRX), discontinuous dynamic recrystallization (DDRX) and particle stimulated nucleation (PSN).
- 1 November 2021
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 881
Comparison of the microstructure evolution and mechanical properties via MDF and ITMT methods
- 1 November 2021
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 881
Comparison of the microstructure evolution and mechanical properties via MDF and ITMT methods
- Open Access
Anisotropic Low Cycle Behavior of the Extruded 7075 Al Alloy
The quasi-static and low cycle fatigue tests of extruded 7075 Al alloy (Φ200 mm) were investigated in three directions: the extrusion direction (ED), the radial direction (RD), and 45° with ED (45°). Grain morphology analysis, texture measurement, and fatigue fracture characterization were conducted to discuss the relationship between microstructure and mechanical properties. The experimental results showed that the ED specimen had higher ultimate tensile strength (UTS) and low cycle fatigue (LCF) properties, which were mainly attributed to the following three causes. First, the grain boundaries (GBs) had an obvious effect on the crack growth. The number of GBs in the three directions was different due to the shape of the grains elongated along the ED. Second, the sharp texture and the small Schmidt factor along the ED explained the higher ultimate tensile strength (UTS) of the ED specimens. Third, fatigue fracture observation showed that the ED specimen had a narrow fatigue striation spacing, which indicated that the plastic deformation of the ED specimen was the smallest in each cycle. In addition, two fatigue prediction models were established to predict the LCF life of extruded 7075 Al alloy, based on the life response behavior of the three directions under different strains.
Open AccessAnisotropic Low Cycle Behavior of the Extruded 7075 Al Alloy
The quasi-static and low cycle fatigue tests of extruded 7075 Al alloy (Φ200 mm) were investigated in three directions: the extrusion direction (ED), the radial direction (RD), and 45° with ED (45°). Grain morphology analysis, texture measurement, and fatigue fracture characterization were conducted to discuss the relationship between microstructure and mechanical properties. The experimental results showed that the ED specimen had higher ultimate tensile strength (UTS) and low cycle fatigue (LCF) properties, which were mainly attributed to the following three causes. First, the grain boundaries (GBs) had an obvious effect on the crack growth. The number of GBs in the three directions was different due to the shape of the grains elongated along the ED. Second, the sharp texture and the small Schmidt factor along the ED explained the higher ultimate tensile strength (UTS) of the ED specimens. Third, fatigue fracture observation showed that the ED specimen had a narrow fatigue striation spacing, which indicated that the plastic deformation of the ED specimen was the smallest in each cycle. In addition, two fatigue prediction models were established to predict the LCF life of extruded 7075 Al alloy, based on the life response behavior of the three directions under different strains.
- Open Access
Microstructure and Texture Evolution of Mg-Gd-Y-Zr Alloy during Reciprocating Upsetting-Extrusion
Reciprocating Upsetting-Extrusion (RUE) deformation process can significantly refine the grains size and weaken the basal plane texture by applying a large cumulative strain to the alloy, which is of great significance to weaken the anisotropy of magnesium (Mg) alloys and increase the application range. In this paper, the Mg-8.27Gd-3.18Y-0.43Zr (wt %) alloy was subjected to isothermal multi-passes RUE. The microstructure and texture evolution, crystal orientation-dependent deformation mechanism of the alloy after deformation were investigated. The results clearly show that with the increase of RUE process, the grains are significantly refined through continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX) mechanisms, the uniformity of the microstructure is improved, and the texture intensity is reduced. At the same time, a large number of particle phases are dynamically precipitated during the deformation process, promoting grain refinement by the particle-stimulated nucleation (PSN) mechanism. The typical [10-10] fiber texture is produced after one pass due to the basal plane of the deformed grains with a relatively high proportion is gradually parallel to the ED during extrusion process. However, the texture concentration is reduced compared with the traditional extrusion deformation, indicating that the upsetting deformation has a certain delay effect on the subsequent extrusion texture generation. After three or four passes deformation, the grain orientation is randomized due to the continuous progress of the dynamic recrystallization process.
Open AccessMicrostructure and Texture Evolution of Mg-Gd-Y-Zr Alloy during Reciprocating Upsetting-Extrusion
Reciprocating Upsetting-Extrusion (RUE) deformation process can significantly refine the grains size and weaken the basal plane texture by applying a large cumulative strain to the alloy, which is of great significance to weaken the anisotropy of magnesium (Mg) alloys and increase the application range. In this paper, the Mg-8.27Gd-3.18Y-0.43Zr (wt %) alloy was subjected to isothermal multi-passes RUE. The microstructure and texture evolution, crystal orientation-dependent deformation mechanism of the alloy after deformation were investigated. The results clearly show that with the increase of RUE process, the grains are significantly refined through continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX) mechanisms, the uniformity of the microstructure is improved, and the texture intensity is reduced. At the same time, a large number of particle phases are dynamically precipitated during the deformation process, promoting grain refinement by the particle-stimulated nucleation (PSN) mechanism. The typical [10-10] fiber texture is produced after one pass due to the basal plane of the deformed grains with a relatively high proportion is gradually parallel to the ED during extrusion process. However, the texture concentration is reduced compared with the traditional extrusion deformation, indicating that the upsetting deformation has a certain delay effect on the subsequent extrusion texture generation. After three or four passes deformation, the grain orientation is randomized due to the continuous progress of the dynamic recrystallization process.
- Open Access
Microstructure, Texture Evolution, and Mechanical Properties of MDFed GWZ Alloy Containing LPSO Phases on the Condition of High and Low Temperature Cycle Deformation
The current work systematically investigated the microstructure, texture evolution, and mechanical properties of MDFed Mg-13Gd-4Y-2Zn-0.5Zr (wt%) alloy (GWZ) on the condition of high and low temperature cycle deformation. The high and low temperature cycle deformation was proposed on the basis of the conventional multi-directional forging (MDF) at decreasing temperature and annealing treatment. As a new method, it was aimed to timely uniform the microstructure and strengthen magnesium (Mg) matrix during the deformation process. A low accumulative strain of 3 after 1 pass resulted in a bimodal microstructure with undynamic recrystallized (unDRXed) regions and dynamic recrystallized (DRXed) grains, while a high accumulative strain of 12 after 4 passes lead to a homogeneous microstructure with fine DRXed grains. According to the experimental results, it indicated that the average grain size of 63 μm after homogenization treatment at 520 was refined remarkably to 5.20 μm after 4 passes at 420 °C through high and low temperature cycle deformation. The area fraction of DRXed grains was increased to 98.4%, which can be regarded as achieving complete DRX after 4 passes. The grain refinement was mainly caused by particle stimulation nucleation (PSN) and mechanism. As the MDF passes and accumulative strain increased, the basal texture was weakened and transformed from a strong basal texture to a random distribution gradually. Compared with conventional MDF at decreasing temperature, the mechanical properties were enhanced effectively. After 4 passes, the ultimate tensile strength (UTS), tensile yield strength (TYS), and failure elongation (FE) were 405 MPa, 305 MPa, and 13.1%, respectively.
Open AccessMicrostructure, Texture Evolution, and Mechanical Properties of MDFed GWZ Alloy Containing LPSO Phases on the Condition of High and Low Temperature Cycle Deformation
The current work systematically investigated the microstructure, texture evolution, and mechanical properties of MDFed Mg-13Gd-4Y-2Zn-0.5Zr (wt%) alloy (GWZ) on the condition of high and low temperature cycle deformation. The high and low temperature cycle deformation was proposed on the basis of the conventional multi-directional forging (MDF) at decreasing temperature and annealing treatment. As a new method, it was aimed to timely uniform the microstructure and strengthen magnesium (Mg) matrix during the deformation process. A low accumulative strain of 3 after 1 pass resulted in a bimodal microstructure with undynamic recrystallized (unDRXed) regions and dynamic recrystallized (DRXed) grains, while a high accumulative strain of 12 after 4 passes lead to a homogeneous microstructure with fine DRXed grains. According to the experimental results, it indicated that the average grain size of 63 μm after homogenization treatment at 520 was refined remarkably to 5.20 μm after 4 passes at 420 °C through high and low temperature cycle deformation. The area fraction of DRXed grains was increased to 98.4%, which can be regarded as achieving complete DRX after 4 passes. The grain refinement was mainly caused by particle stimulation nucleation (PSN) and mechanism. As the MDF passes and accumulative strain increased, the basal texture was weakened and transformed from a strong basal texture to a random distribution gradually. Compared with conventional MDF at decreasing temperature, the mechanical properties were enhanced effectively. After 4 passes, the ultimate tensile strength (UTS), tensile yield strength (TYS), and failure elongation (FE) were 405 MPa, 305 MPa, and 13.1%, respectively.
- 1 May 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (5) , 056530
Study on the hot tensile behavior, microstructure and fracture of Mg-13Gd-4Y-2Zn-0.5Zr alloy
The stress-strain curves of Mg-13Gd-4Y-2Zn-0.5Zr alloy are obtained by the hot tensile test at the temperature range from 400 to 520 ℃ and strain rate range from 0.001 to 0.5 s^(−1). Then, the hot tensile behavior, microstructure and fracture are studied. The flow stress decreases with increasing temperature and decreasing strain rate, and the constitutive equation of peak stress can be expressed by an Arrhenius equation as follows:Strain rate=[1.367*10^(16)]*{[sinh(0.0104*Stress)]^(5.446)}*exp[(- 259.13)/(8.314*Temperature)] .The kinking and dynamic recrystallization (DRX) are the major softening mechanisms, and the greater kinking angle and the more DRX grains can be observed by increasing temperature and decreasing strain rate. Therefore, the strain value at fracture (SVF) is the greatest at the temperature of 520 ℃ and strain rate of 0.001 s^(−1).The microcrack in all specimens generate at the grain boundary and the interface between the block phase and Mg matrix. And the fracture characteristic gradually develops from brittle fracture to ductile fracture with increasing temperature and decreasing strain rate.
- 1 May 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (5) , 056530
Study on the hot tensile behavior, microstructure and fracture of Mg-13Gd-4Y-2Zn-0.5Zr alloy
The stress-strain curves of Mg-13Gd-4Y-2Zn-0.5Zr alloy are obtained by the hot tensile test at the temperature range from 400 to 520 ℃ and strain rate range from 0.001 to 0.5 s^(−1). Then, the hot tensile behavior, microstructure and fracture are studied. The flow stress decreases with increasing temperature and decreasing strain rate, and the constitutive equation of peak stress can be expressed by an Arrhenius equation as follows:Strain rate=[1.367*10^(16)]*{[sinh(0.0104*Stress)]^(5.446)}*exp[(- 259.13)/(8.314*Temperature)] .The kinking and dynamic recrystallization (DRX) are the major softening mechanisms, and the greater kinking angle and the more DRX grains can be observed by increasing temperature and decreasing strain rate. Therefore, the strain value at fracture (SVF) is the greatest at the temperature of 520 ℃ and strain rate of 0.001 s^(−1).The microcrack in all specimens generate at the grain boundary and the interface between the block phase and Mg matrix. And the fracture characteristic gradually develops from brittle fracture to ductile fracture with increasing temperature and decreasing strain rate.