Ilona Rolfes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ilona Rolfes has a total of 257 co-authors. Here are the top co-authors by number of shared publications:
Christian Schulz
Department for Electrical Engineering and Information Technologies, Institute of Microwave Systems, Ruhr University Bochum, Bochum, Germany
27 shared publications- Jan Barowski
Institute of Microwave Systems, Ruhr University Bochum, Bochum, Germany
27 shared publications Thomas Musch
Institute of Electronic Circuits, Ruhr-University Bochum, Germany
22 shared publicationsChristoph Baer
Institute of Electronic Circuits, Ruhr-University Bochum, Germany
18 shared publicationsJan Barowski
18 shared publicationsT. Musch
Institute of Electronic Circuits, Ruhr-University Bochum, Germany
18 shared publications
Latest Publications
- Open Access
- 9 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Radar Systems
- Vol. 4, 787-798
Augmenting Smoke Detection Systems via Radar and Deep Learning for Continuous Hazard and Condition Monitoring: A Multispectral Analysis
Traditional smoke detection systems share inherent limitations. Inter alia, these systems are fundamentally limited by their purely reactive and non-predictive operation. The objective of this contribution is to extend the advantageous probing capabilities of radar systems toward the augmentation of traditional smoke detectors for continuous condition and hazard monitoring. Particular emphasis is placed here on early-stage hazards and critical precursor conditions for preventive fire safety. To this end, static-target radar echoes are classified using deep learning (DL) methods by extracting characteristic patterns caused by subtle changes in the surrounding medium (e.g., water vapor). Measurements were conducted employing ultra-wideband frequency-modulated continuous-wave (FMCW) radar systems operating from 80 GHz to 240 GHz, in a controlled indoor proof-of-concept setup, enabling a systematic multispectral analysis. Several scenarios representative of domestic settings were considered, including the frying of a burger patty (UL 268 standard). The proposed concept achieves classification accuracies of more than 90%, even under strong restrictions. The developed models remain lightweight and fast, well suited for embedded implementations.
- 9 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Radar Systems
- Vol. 4, 787-798
Open AccessAugmenting Smoke Detection Systems via Radar and Deep Learning for Continuous Hazard and Condition Monitoring: A Multispectral Analysis
Traditional smoke detection systems share inherent limitations. Inter alia, these systems are fundamentally limited by their purely reactive and non-predictive operation. The objective of this contribution is to extend the advantageous probing capabilities of radar systems toward the augmentation of traditional smoke detectors for continuous condition and hazard monitoring. Particular emphasis is placed here on early-stage hazards and critical precursor conditions for preventive fire safety. To this end, static-target radar echoes are classified using deep learning (DL) methods by extracting characteristic patterns caused by subtle changes in the surrounding medium (e.g., water vapor). Measurements were conducted employing ultra-wideband frequency-modulated continuous-wave (FMCW) radar systems operating from 80 GHz to 240 GHz, in a controlled indoor proof-of-concept setup, enabling a systematic multispectral analysis. Several scenarios representative of domestic settings were considered, including the frying of a burger patty (UL 268 standard). The proposed concept achieves classification accuracies of more than 90%, even under strong restrictions. The developed models remain lightweight and fast, well suited for embedded implementations.
- Open Access
- 11 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 27 (6) , 80-87
Amplifying Rocket RCS With Retroreflective Structure
This article presents the development and validation of a retroreflective structure designed to improve the radar detection of amateur rockets. The work was carried out as part of the Student Design Competition (SDC) at the 2025 International Microwave Symposium (IMS) in San Francisco. The goal was to increase the radar visibility of rockets with cylindrical fuselages as these are difficult to detect at high angles of incidence due to their low monostatic radar cross section (RCS). The proposed solution employs passive, air-filled slotted waveguide (SWG) antennas realized through additive manufacturing and metallic coating. The structure meets the stringent requirements for weight, size, and mechanical stability. Experimental validation shows that the developed structure significantly improves radar detection compared with a simple cylindrical body.
- 11 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 27 (6) , 80-87
Open AccessAmplifying Rocket RCS With Retroreflective Structure
This article presents the development and validation of a retroreflective structure designed to improve the radar detection of amateur rockets. The work was carried out as part of the Student Design Competition (SDC) at the 2025 International Microwave Symposium (IMS) in San Francisco. The goal was to increase the radar visibility of rockets with cylindrical fuselages as these are difficult to detect at high angles of incidence due to their low monostatic radar cross section (RCS). The proposed solution employs passive, air-filled slotted waveguide (SWG) antennas realized through additive manufacturing and metallic coating. The structure meets the stringent requirements for weight, size, and mechanical stability. Experimental validation shows that the developed structure significantly improves radar detection compared with a simple cylindrical body.
- Open Access
- 4 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (20) , 37934-37942
Broadband Disposable Biosensors Based on Dielectric Waveguide Ring Resonators
This paper presents a broadband, 3D-printed disposable biosensor based on a dielectric waveguide ring resonator (DWGR) fabricated from high-impact polystyrene (HIPS). The sensor is specifically designed to quantify trace amounts of water in oil, a critical indicator of fluid degradation and maintenance requirements. The sensor operates in the D-Band in a frequency range of 110-170 GHz, and is designed for high-precision permittivity sensing. Key design and post-processing steps are shown, including a resonance-minima extraction framework enabling accurate material characterization. A proof of concept is presented using a vector network analyzer (VNA). After this further measurements confirming the accurate detection of known reference materials are presented. Furthermore, the sensor’s capability to detect oil degradation through water contamination is also demonstrated. Overall, the proposed approach enables high-resolution permittivity sensing over a broad frequency range and represents promising results for future disposable fluid condition monitoring.
- 4 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (20) , 37934-37942
Open AccessBroadband Disposable Biosensors Based on Dielectric Waveguide Ring Resonators
This paper presents a broadband, 3D-printed disposable biosensor based on a dielectric waveguide ring resonator (DWGR) fabricated from high-impact polystyrene (HIPS). The sensor is specifically designed to quantify trace amounts of water in oil, a critical indicator of fluid degradation and maintenance requirements. The sensor operates in the D-Band in a frequency range of 110-170 GHz, and is designed for high-precision permittivity sensing. Key design and post-processing steps are shown, including a resonance-minima extraction framework enabling accurate material characterization. A proof of concept is presented using a vector network analyzer (VNA). After this further measurements confirming the accurate detection of known reference materials are presented. Furthermore, the sensor’s capability to detect oil degradation through water contamination is also demonstrated. Overall, the proposed approach enables high-resolution permittivity sensing over a broad frequency range and represents promising results for future disposable fluid condition monitoring.
- Open Access
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (4) , 907-917
Considerations on Sensor Fusion of Multiple Ultrawideband Radar Sensors Operating in Non-Adjacent Frequency Bands
This paper presents a novel sensor fusion approach to enhance radar measurement bandwidth and range resolution by integrating data from non-adjacent frequency bands. While ultrawideband (UWB) radar systems offer high resolution, they are often constrained by regulatory limitations and hardware bandwidth restrictions. To overcome these challenges, we investigate on merging intermediate frequency signals from multiple frequency-modulated continuous wave (FMCW) radar sensors operating in separate bands. Though this effectively broadens the usable bandwidth, challenges arise from uncovered spectral regions in between the sensor bands. A frequency domain model is employed to address these systematic challenges in multi-band fusion and to quantify side-lobe-levels and pulse-widths. Furthermore, we discuss the establishment of a common phase reference by means of calibration. The investigations are validated through simulations and experimental measurements using W-band (68–93 GHz), D-band (122–170 GHz), and J-band (205–248 GHz) FMCW sensors. Finally, it is shown that model-based interpolation between the bands significantly removes undesired distortions. Results demonstrate a significant enhancement in range resolution, particularly benefiting applications such as non-destructive testing and high-precision material characterization. In these applications, the approach provides a viable alternative to photonic and optical measurement techniques, leveraging the advantages of compact, MMIC-based radar sensors while overcoming inherent bandwidth limitations.
- 16 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (4) , 907-917
Open AccessConsiderations on Sensor Fusion of Multiple Ultrawideband Radar Sensors Operating in Non-Adjacent Frequency Bands
This paper presents a novel sensor fusion approach to enhance radar measurement bandwidth and range resolution by integrating data from non-adjacent frequency bands. While ultrawideband (UWB) radar systems offer high resolution, they are often constrained by regulatory limitations and hardware bandwidth restrictions. To overcome these challenges, we investigate on merging intermediate frequency signals from multiple frequency-modulated continuous wave (FMCW) radar sensors operating in separate bands. Though this effectively broadens the usable bandwidth, challenges arise from uncovered spectral regions in between the sensor bands. A frequency domain model is employed to address these systematic challenges in multi-band fusion and to quantify side-lobe-levels and pulse-widths. Furthermore, we discuss the establishment of a common phase reference by means of calibration. The investigations are validated through simulations and experimental measurements using W-band (68–93 GHz), D-band (122–170 GHz), and J-band (205–248 GHz) FMCW sensors. Finally, it is shown that model-based interpolation between the bands significantly removes undesired distortions. Results demonstrate a significant enhancement in range resolution, particularly benefiting applications such as non-destructive testing and high-precision material characterization. In these applications, the approach provides a viable alternative to photonic and optical measurement techniques, leveraging the advantages of compact, MMIC-based radar sensors while overcoming inherent bandwidth limitations.
- Open Access
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 9 (6) , 1-4
Fluidic-Integrated Dielectric Waveguide Mach–Zehnder Sensor for THz Spectroscopy
This letter presents the design, optimization, and characterization of a dielectric slot-waveguide (DSWG)-based sensor for fluid sensing applications. The sensor is inspired by the concept of a Mach–Zehnder interferometer and utilizes high field confinement within the slot region to enhance sensitivity to permittivity changes, overcoming typical problems of other fluidic terahertz (THz) domain sensors. Advanced 3D-electromagnetic simulations were employed to optimize key design parameters, ensuring low loss and efficient sensing performance. Measurements with acetone, isopropanol, and butanol demonstrate the sensor's ability to distinguish fluids based on their permittivity, with notable differences in time shifts and attenuation. These results highlight the potential of DSWG-based sensors for precise and reliable THz sensing applications.
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 9 (6) , 1-4
Open AccessFluidic-Integrated Dielectric Waveguide Mach–Zehnder Sensor for THz Spectroscopy
This letter presents the design, optimization, and characterization of a dielectric slot-waveguide (DSWG)-based sensor for fluid sensing applications. The sensor is inspired by the concept of a Mach–Zehnder interferometer and utilizes high field confinement within the slot region to enhance sensitivity to permittivity changes, overcoming typical problems of other fluidic terahertz (THz) domain sensors. Advanced 3D-electromagnetic simulations were employed to optimize key design parameters, ensuring low loss and efficient sensing performance. Measurements with acetone, isopropanol, and butanol demonstrate the sensor's ability to distinguish fluids based on their permittivity, with notable differences in time shifts and attenuation. These results highlight the potential of DSWG-based sensors for precise and reliable THz sensing applications.
- Open Access
- 10 March 2025
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 17 (2) , 213-214
EuMC 2023 Special Issue
- 10 March 2025
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 17 (2) , 213-214
Open AccessEuMC 2023 Special Issue
- Open Access
- 4 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (2) , 344-355
Simultaneous Localization and Mapping (SLAM) for Room Exploration Using Ultrawideband Millimeterwave FMCW Radar
Simultaneous Localization and Mapping (SLAM) of indoor scenarios is usually based on camera or lidar sensors as data sources. However, radar based room scanning offers several complementary advantages to these systems. Among other features, radar sensors are more robust to optical opacities, for example, those caused by smoke and dust in emergency scenarios or in harsh environments. Furthermore, the coherent measurement principle of radar sensors provides highly precise distance information that can be utilized to track the exact position and dimensions of the visible objects. In contrast to camera and lidar, radar applications in room exploration are up to now limited by reduced spatial, i.e. mostly angular/lateral, resolution. This is due to the comparably large wavelength of the utilized signals. This work demonstrates the capabilities of ultrawideband millimeterwave Frequency Modulated Continuous Wave (FMCW) radar sensors operating around 80 GHz in conjunction with the Synthetic Aperture Radar (SAR) imaging method. To allow imaging whilst moving, self-localization techniques based on sub-aperture processing are evaluated. Therefore, we demonstrate a detailed mapping procedure for room exploration applications by exploiting large absolute bandwidths of more than 20 GHz with high resolution imaging techniques on a mobile robot platform.
- 4 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (2) , 344-355
Open AccessSimultaneous Localization and Mapping (SLAM) for Room Exploration Using Ultrawideband Millimeterwave FMCW Radar
Simultaneous Localization and Mapping (SLAM) of indoor scenarios is usually based on camera or lidar sensors as data sources. However, radar based room scanning offers several complementary advantages to these systems. Among other features, radar sensors are more robust to optical opacities, for example, those caused by smoke and dust in emergency scenarios or in harsh environments. Furthermore, the coherent measurement principle of radar sensors provides highly precise distance information that can be utilized to track the exact position and dimensions of the visible objects. In contrast to camera and lidar, radar applications in room exploration are up to now limited by reduced spatial, i.e. mostly angular/lateral, resolution. This is due to the comparably large wavelength of the utilized signals. This work demonstrates the capabilities of ultrawideband millimeterwave Frequency Modulated Continuous Wave (FMCW) radar sensors operating around 80 GHz in conjunction with the Synthetic Aperture Radar (SAR) imaging method. To allow imaging whilst moving, self-localization techniques based on sub-aperture processing are evaluated. Therefore, we demonstrate a detailed mapping procedure for room exploration applications by exploiting large absolute bandwidths of more than 20 GHz with high resolution imaging techniques on a mobile robot platform.
- Open Access
- 30 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (1) , 361-372
Smoke Detection and Combustion Analysis Using Millimeter-Wave Radar Measurements
Understanding and detecting smoke effectively is crucial in emergency scenarios where traditional optical methods may fail. This article investigates the definition of smoke and its characterization from an electromagnetic perspective, focusing particularly on the use of frequency-modulated continuous wave (FMCW) radar sensors operating in the millimeter-wave range. We explore the influence of both laminar and turbulent smoke flows on the measurement accuracy. Our study is grounded in dielectric models in the millimeter-wave spectrum, demonstrating that the dielectric properties of smoke exhibit minimal variations. Consequently, we use phase-based radar signal processing to detect these subtle changes. Unlike previous studies that primarily evaluate sensor performance, this article aims to use the minimal impact on the measured signal to characterize different smoke scenarios comprehensively. Our findings demonstrate that radar sensors can provide valuable insights into smoke properties and are suitable to extend material model for millimeter-wave frequencies, enhancing situational awareness and response strategies in smoke-obscured environments.
- 30 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (1) , 361-372
Open AccessSmoke Detection and Combustion Analysis Using Millimeter-Wave Radar Measurements
Understanding and detecting smoke effectively is crucial in emergency scenarios where traditional optical methods may fail. This article investigates the definition of smoke and its characterization from an electromagnetic perspective, focusing particularly on the use of frequency-modulated continuous wave (FMCW) radar sensors operating in the millimeter-wave range. We explore the influence of both laminar and turbulent smoke flows on the measurement accuracy. Our study is grounded in dielectric models in the millimeter-wave spectrum, demonstrating that the dielectric properties of smoke exhibit minimal variations. Consequently, we use phase-based radar signal processing to detect these subtle changes. Unlike previous studies that primarily evaluate sensor performance, this article aims to use the minimal impact on the measured signal to characterize different smoke scenarios comprehensively. Our findings demonstrate that radar sensors can provide valuable insights into smoke properties and are suitable to extend material model for millimeter-wave frequencies, enhancing situational awareness and response strategies in smoke-obscured environments.
- Open Access
- 13 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-10
Radar-Enabled Millimeter-Wave Sensing of Fire Interactions
This article investigates the impact of fire on electromagnetic waves within a 70–90 GHz frequency range. To gain a deeper understanding of interactions between fire and radar signals, it is essential to consider a dielectric model for flames. Three primary mechanisms have been identified: the relative permittivity of reaction products, absorption of ionized gases, and the influence of incomplete combustion. To explore these mechanisms, two distinct test fires (TF) were examined in a fire laboratory in a style of the European standard EN54. Initial experimental series involved the combustion of liquid n-heptane, followed by a series of experiments focusing on open polyurethane combustion. Measurements were conducted using a frequency modulated continuous wave radar sensor. Additionally, a PT1000 resistor and an optical extraction measuring instrument were used as reference. Based on highly precise phase evaluation of the measurement signal, initial correlations were established between the radar-measured phase and the measured particle density. The proven ability to differentiate between two TF suggests the potential for fire detection using frequency-modulated continuous wave (FMCW) radar sensors.
- 13 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-10
Open AccessRadar-Enabled Millimeter-Wave Sensing of Fire Interactions
This article investigates the impact of fire on electromagnetic waves within a 70–90 GHz frequency range. To gain a deeper understanding of interactions between fire and radar signals, it is essential to consider a dielectric model for flames. Three primary mechanisms have been identified: the relative permittivity of reaction products, absorption of ionized gases, and the influence of incomplete combustion. To explore these mechanisms, two distinct test fires (TF) were examined in a fire laboratory in a style of the European standard EN54. Initial experimental series involved the combustion of liquid n-heptane, followed by a series of experiments focusing on open polyurethane combustion. Measurements were conducted using a frequency modulated continuous wave radar sensor. Additionally, a PT1000 resistor and an optical extraction measuring instrument were used as reference. Based on highly precise phase evaluation of the measurement signal, initial correlations were established between the radar-measured phase and the measured particle density. The proven ability to differentiate between two TF suggests the potential for fire detection using frequency-modulated continuous wave (FMCW) radar sensors.