Carlos A. Jarro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Carlos A. Jarro has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Piao Liu
University of Kentucky
2 shared publicationsSuresh Rajaputra
University of Kentucky
2 shared publicationsB Nadimpally
SunEdison, 501 Pearl Drive, St. Peters, MO 63376, USA
1 shared publication- Eugenii U. Donev
Department of Electrical and Computer Engineering, University of Kentucky, 453 F. Paul Anderson Tower, Lexington, KY (USA)
1 shared publication Glenn Gibson
University of Texas
1 shared publicationJ. Todd Hastings
1 shared publication
Latest Publications
- 21 November 2016
- Published by IOP Publishing in Nanotechnology
- Vol. 27 (50) , 505302
Flexible anodized aluminum oxide membranes with customizable back contact materials
Anodized aluminum oxide (AAO) membranes were fabricated using flexible substrate/carrier material. This method facilitates the use of AAO templates with many different materials as substrates that are otherwise incompatible with most anodization techniques. Thin titanium (Ti) and tungsten (W) layers were employed as interlayer materials. Titanium enhances adhesion. Tungsten not only helps eliminate the barrier layer but also plays a critical role in enabling the use of flexible substrates. The resulting flexible templates provide new, exciting opportunities in photovoltaic and other device applications. CuInSe2 nanowires were electrochemically deposited into porous AAO templates with molybdenum (Mo) as the back contact material. The feasibility of using any material to form a contact with semiconductor nanowires has been demonstrated for the first time enabling new avenues in photovoltaic applications.
- 21 November 2016
- Published by IOP Publishing in Nanotechnology
- Vol. 27 (50) , 505302
Flexible anodized aluminum oxide membranes with customizable back contact materials
Anodized aluminum oxide (AAO) membranes were fabricated using flexible substrate/carrier material. This method facilitates the use of AAO templates with many different materials as substrates that are otherwise incompatible with most anodization techniques. Thin titanium (Ti) and tungsten (W) layers were employed as interlayer materials. Titanium enhances adhesion. Tungsten not only helps eliminate the barrier layer but also plays a critical role in enabling the use of flexible substrates. The resulting flexible templates provide new, exciting opportunities in photovoltaic and other device applications. CuInSe2 nanowires were electrochemically deposited into porous AAO templates with molybdenum (Mo) as the back contact material. The feasibility of using any material to form a contact with semiconductor nanowires has been demonstrated for the first time enabling new avenues in photovoltaic applications.
- 1 November 2013
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 31 (6) , 06F303
Control of the structure and density of silver nanoparticles obtained by laser-induced chemical deposition from liquids
- 1 November 2013
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 31 (6) , 06F303
Control of the structure and density of silver nanoparticles obtained by laser-induced chemical deposition from liquids
- 26 October 2012
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 30 (6) , 06FD02
Silver patterning using an atomic force microscope tip and laser-induced chemical deposition from liquids
This article presents a new direct patterning technique in which laser photoreduction of silver from a liquid is controlled by a scanning atomic force microscope tip. Contrary to expectations, the tip suppresses, rather than enhances, deposition on the underlying substrate, and this suppression persists in the absence of the tip. Experiments presented here exclude three potential mechanisms: purely mechanical material removal, depletion of the silver precursor, and preferential photoreduction on existing deposits. These results represent a first step toward direct, negative tone, tip-based patterning of functional materials.
- 26 October 2012
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 30 (6) , 06FD02
Silver patterning using an atomic force microscope tip and laser-induced chemical deposition from liquids
This article presents a new direct patterning technique in which laser photoreduction of silver from a liquid is controlled by a scanning atomic force microscope tip. Contrary to expectations, the tip suppresses, rather than enhances, deposition on the underlying substrate, and this suppression persists in the absence of the tip. Experiments presented here exclude three potential mechanisms: purely mechanical material removal, depletion of the silver precursor, and preferential photoreduction on existing deposits. These results represent a first step toward direct, negative tone, tip-based patterning of functional materials.
- 24 February 2011
- Published by IOP Publishing in Nanotechnology
- Vol. 22 (14) , 145304
Cadmium sulfide nanowires for the window semiconductor layer in thin film CdS–CdTe solar cells
Thin film CdS/CdTe heterojunction device is a leading technology for the solar cells of the next generation. We report on two novel device configurations for these cells where the traditional CdS window layer is replaced by nanowires (NW) of CdS, embedded in an aluminum oxide matrix or free-standing. An estimated 26.8% improvement in power conversion efficiency over the traditional device structure is expected, primarily because of the enhanced spectral transmission of sunlight through the NW-CdS layer and a reduction in the junction area/optical area ratio. In initial experiments, nanostructured devices of the two designs were fabricated and a power conversion efficiency value of 6.5% was achieved.
- 24 February 2011
- Published by IOP Publishing in Nanotechnology
- Vol. 22 (14) , 145304
Cadmium sulfide nanowires for the window semiconductor layer in thin film CdS–CdTe solar cells
Thin film CdS/CdTe heterojunction device is a leading technology for the solar cells of the next generation. We report on two novel device configurations for these cells where the traditional CdS window layer is replaced by nanowires (NW) of CdS, embedded in an aluminum oxide matrix or free-standing. An estimated 26.8% improvement in power conversion efficiency over the traditional device structure is expected, primarily because of the enhanced spectral transmission of sunlight through the NW-CdS layer and a reduction in the junction area/optical area ratio. In initial experiments, nanostructured devices of the two designs were fabricated and a power conversion efficiency value of 6.5% was achieved.