Karol Żarski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Karol Żarski has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Jacek Oskarbski
Faculty of Civil and Environmental Engineering, Gdansk University of Technology, 80-233 Gdansk, Poland
11 shared publications - Krystian Birr
Faculty of Civil and Environmental Engineering, Gdansk University of Technology, 80-233 Gdansk, Poland
2 shared publications - Marcin Zawisza
Gdansk University of Technology
2 shared publications Tomasz Marcinkowski
Gdańsk University of Technology, 80-255, Narutowicza 11/12, Gdańsk, Poland
2 shared publicationsGrzegorz Oskarbski
Gdańsk University of Technology, 80-255, Narutowicza 11/12, Gdańsk, Poland
1 shared publicationIzabela Oskarbska
Gdańsk University of Technology, 80-255, Narutowicza 11/12, Gdańsk, Poland
1 shared publication
Latest Publications
- Open Access
- 31 December 2024
- Published by Politechnika Warszawska - Warsaw University of Technology in Archives of Transport
- Vol. 72 (4) , 43-73
Impact of different car-following models on estimating safety and emissions on signal-controlled intersections using microscopic simulations
This paper examines the influence of two selected car-following models on the outcomes of microscopic traffic simulations. The authors begin by reviewing the literature on the various traffic models, methods for estimating energy consumption, fuel use, and emissions. The authors discuss using surrogate safety measures derived from analysing vehicle trajectories in a microscopic traffic model to estimate safety levels. This paper also outlines the authors' approach to data acquisition and processing at the chosen test site. Most data are sourced from the city's Intelligent Transport System (ITS) services, including traffic flow volume, vehicle speed, and public transport travel times. The data gathered from Automatic Vehicle Location (AVL) systems was compared to manual travel time measurements. Depending on the analysed section Mean Average Error (MAE) ranging from 3 to 5 seconds was obtained, however, Mean Absolute Percentage Error (MAPE) ranged from 7.46% to 30.01%. The proposed method aims to evaluate the precision of the microscopic model in replicating real road networks and traffic based on available datasets. Two car-following models (CFM), Wiedemann 74 (W74), and Wiedemann 99 (W99) are chosen for further analysis. The models were validated using the GEH statistic and by comparing speed distributions. Both the models yielded satisfactory results. Different scenarios involving changes in traffic flow and to traffic signal configurations were analysed. While both W74 and W99 yielded satisfactory results, there were discernible disparities in the analyses. In general, W99 yields less favourable results, characterised by emissions, and delays compared to W74. Depending on the scenarios compared, the number of conflicts for W74 varied up to 56% (scenarios 2 and 4), and up to 78% for W99 (scenarios 1 and 4). The methodology presented by the authors can be used in future research to analyse various traffic control solutions concerning their impact on the environment and traffic safety. The observed differences underscore the importance of careful model selection and presented approach can serve as a foundation for developing guidelines for microscopic modelling and a multi-criteria approach to selecting the most effective implementation scenarios.
- 31 December 2024
- Published by Politechnika Warszawska - Warsaw University of Technology in Archives of Transport
- Vol. 72 (4) , 43-73
Open AccessImpact of different car-following models on estimating safety and emissions on signal-controlled intersections using microscopic simulations
This paper examines the influence of two selected car-following models on the outcomes of microscopic traffic simulations. The authors begin by reviewing the literature on the various traffic models, methods for estimating energy consumption, fuel use, and emissions. The authors discuss using surrogate safety measures derived from analysing vehicle trajectories in a microscopic traffic model to estimate safety levels. This paper also outlines the authors' approach to data acquisition and processing at the chosen test site. Most data are sourced from the city's Intelligent Transport System (ITS) services, including traffic flow volume, vehicle speed, and public transport travel times. The data gathered from Automatic Vehicle Location (AVL) systems was compared to manual travel time measurements. Depending on the analysed section Mean Average Error (MAE) ranging from 3 to 5 seconds was obtained, however, Mean Absolute Percentage Error (MAPE) ranged from 7.46% to 30.01%. The proposed method aims to evaluate the precision of the microscopic model in replicating real road networks and traffic based on available datasets. Two car-following models (CFM), Wiedemann 74 (W74), and Wiedemann 99 (W99) are chosen for further analysis. The models were validated using the GEH statistic and by comparing speed distributions. Both the models yielded satisfactory results. Different scenarios involving changes in traffic flow and to traffic signal configurations were analysed. While both W74 and W99 yielded satisfactory results, there were discernible disparities in the analyses. In general, W99 yields less favourable results, characterised by emissions, and delays compared to W74. Depending on the scenarios compared, the number of conflicts for W74 varied up to 56% (scenarios 2 and 4), and up to 78% for W99 (scenarios 1 and 4). The methodology presented by the authors can be used in future research to analyse various traffic control solutions concerning their impact on the environment and traffic safety. The observed differences underscore the importance of careful model selection and presented approach can serve as a foundation for developing guidelines for microscopic modelling and a multi-criteria approach to selecting the most effective implementation scenarios.
- Open Access
Bicycle Traffic Model for Sustainable Urban Mobility Planning
Modelling tools and transport models are required to assess the impact of measures for the effective planning of cycling routes in cities. This paper presents the methodology for developing a four-stage macroscopic model of bicycle traffic for the city of Gdynia, and its use in planning new bicycle routes, considering a modal shift. The model presented in this paper allows for the evaluation of the influence of the characteristics of the cycling infrastructure, along with the development of the cycling network based on the choice of cycling as an alternative to other modes of transport, by taking into account the modal shift. The model takes into account the influence of the longitudinal gradient, link, and surface type of cycling routes on the distribution and demand for bicycle traffic. The results of our research allow us to assess the impact of planned cycling routes on the reduction in the volume of car traffic, which is crucial for reducing energy consumption and negative environmental impacts. Experiences from the application of the model in Gdynia suggest that the model provides a strong basis to support mobility planning and monitoring processes in cities worldwide. Cities should take into account the methods proposed in this paper when planning the development of their transport systems.
Open AccessBicycle Traffic Model for Sustainable Urban Mobility Planning
Modelling tools and transport models are required to assess the impact of measures for the effective planning of cycling routes in cities. This paper presents the methodology for developing a four-stage macroscopic model of bicycle traffic for the city of Gdynia, and its use in planning new bicycle routes, considering a modal shift. The model presented in this paper allows for the evaluation of the influence of the characteristics of the cycling infrastructure, along with the development of the cycling network based on the choice of cycling as an alternative to other modes of transport, by taking into account the modal shift. The model takes into account the influence of the longitudinal gradient, link, and surface type of cycling routes on the distribution and demand for bicycle traffic. The results of our research allow us to assess the impact of planned cycling routes on the reduction in the volume of car traffic, which is crucial for reducing energy consumption and negative environmental impacts. Experiences from the application of the model in Gdynia suggest that the model provides a strong basis to support mobility planning and monitoring processes in cities worldwide. Cities should take into account the methods proposed in this paper when planning the development of their transport systems.
- Open Access
Assessment of the Speed Management Impact on Road Traffic Safety on the Sections of Motorways and Expressways Using Simulation Methods
Methods used to evaluate the impact of Intelligent Transport System (ITS) services on road safety are usually based on expert assessments or statistical studies. However, commonly used methods are challenging to apply in the planning process of ITS services. This paper presents the methodology of research using surrogate safety measures calculated and calibrated with the use of simulation techniques and a driving simulator. This approach supports the choice of the type of ITS services that are beneficial for traffic efficiency and road safety. This paper presents results of research on the influence of selected scenarios of variable speed limits on the efficiency and safety of traffic on the sections of motorways and expressways in various traffic conditions. The driving simulator was used to estimate the efficiency of lane-keeping by the driver. The simulation traffic models were calibrated using driving simulator data and roadside sensor data. The traffic models made it possible to determine surrogate safety measures (number of conflicts and their severity) in selected scenarios of using ITS services. The presented studies confirmed the positive impact of Variable Speed Limits (VSLs) on the level of road safety and traffic efficiency. This paper also presents recommendations and plans for further research in this area.
Open AccessAssessment of the Speed Management Impact on Road Traffic Safety on the Sections of Motorways and Expressways Using Simulation Methods
Methods used to evaluate the impact of Intelligent Transport System (ITS) services on road safety are usually based on expert assessments or statistical studies. However, commonly used methods are challenging to apply in the planning process of ITS services. This paper presents the methodology of research using surrogate safety measures calculated and calibrated with the use of simulation techniques and a driving simulator. This approach supports the choice of the type of ITS services that are beneficial for traffic efficiency and road safety. This paper presents results of research on the influence of selected scenarios of variable speed limits on the efficiency and safety of traffic on the sections of motorways and expressways in various traffic conditions. The driving simulator was used to estimate the efficiency of lane-keeping by the driver. The simulation traffic models were calibrated using driving simulator data and roadside sensor data. The traffic models made it possible to determine surrogate safety measures (number of conflicts and their severity) in selected scenarios of using ITS services. The presented studies confirmed the positive impact of Variable Speed Limits (VSLs) on the level of road safety and traffic efficiency. This paper also presents recommendations and plans for further research in this area.
- Open Access
- 1 December 2019
- Published by Index Copernicus in Journal of Konbin
- Vol. 49 (4) , 297-320
Use of Data from Satellite Navigation System in Operational and Strategic Management of Transport in Cities
The article presents the possibilities of using data from the Global Positioning System for the development of traffic models and examples of use this data in the transport management. Traffic models are useful tools in planning and evaluation of transport solutions, but also can be used for current, operational transport management.
- 1 December 2019
- Published by Index Copernicus in Journal of Konbin
- Vol. 49 (4) , 297-320
Open AccessUse of Data from Satellite Navigation System in Operational and Strategic Management of Transport in Cities
The article presents the possibilities of using data from the Global Positioning System for the development of traffic models and examples of use this data in the transport management. Traffic models are useful tools in planning and evaluation of transport solutions, but also can be used for current, operational transport management.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Methodology of research on the impact of ramp metering on the safety and efficiency of road traffic using transport models
The methods currently used to assess the impact of Intelligent Transport Systems (ITS) services on traffic safety and efficiency are mainly based on expert assessments, statistical studies or traffic models that need further development. There is no structured, uniform evaluation method to compare the impact of different ITS services and their different configurations. The impact of ITS deployment on the road network adjacent to motorways or expressways is usually not taken into account for simulation studies. The approach presented in the paper takes into account the impact of ITS deployment on road traffic efficiency and safety in areas including major roads and alternative routes. The paper presents a methodology for testing the effectiveness of the implementation of a selected ITS service, which is ramp metering. An approach has been applied in which the impact of ITS services is analyzed with the use of a test road network in macro, meso and microscopic transport models. The evaluation of solutions was carried out on the basis of key traffic efficiency indicators. Surrogate measures were used for the assessment of the impact of ramp metering on road traffic safety.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Methodology of research on the impact of ramp metering on the safety and efficiency of road traffic using transport models
The methods currently used to assess the impact of Intelligent Transport Systems (ITS) services on traffic safety and efficiency are mainly based on expert assessments, statistical studies or traffic models that need further development. There is no structured, uniform evaluation method to compare the impact of different ITS services and their different configurations. The impact of ITS deployment on the road network adjacent to motorways or expressways is usually not taken into account for simulation studies. The approach presented in the paper takes into account the impact of ITS deployment on road traffic efficiency and safety in areas including major roads and alternative routes. The paper presents a methodology for testing the effectiveness of the implementation of a selected ITS service, which is ramp metering. An approach has been applied in which the impact of ITS services is analyzed with the use of a test road network in macro, meso and microscopic transport models. The evaluation of solutions was carried out on the basis of key traffic efficiency indicators. Surrogate measures were used for the assessment of the impact of ramp metering on road traffic safety.
- Open Access
- 16 November 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 231, 02008
Methodology of research on the impact of ITS services on the safety and efficiency of road traffic using transport models
The current assessment of the impact of Intelligent Transport System (ITS) services on the level of traffic safety and efficiency is based mainly on expert assessments, statistical surveys or several traffic safety models requiring development. There is no structured, uniform assessment method that would give the opportunity to compare the impact of ITS services and their different configurations. The paper presents the methodology for researching the effectiveness of ITS services implementation using transport models and key indicators allowing such an assessment. An approach was used in which the impact of ITS services is analysed using macro, meso and microscopic models. Macro and mesoscopic models allow estimation of the impact of ITS services on the efficiency of transport network operation and constitute the basis of analyses at the microscopic level, which takes into account the behaviour of drivers through the use of car following and lane change models. As part of the analyses, road network test models (for motorways and expressways along with an alternative route) were developed. Test models include road class, network topology, and different traffic intensity. The models were calibrated using real data (data from the traffic measurement station, data measured in the field, traffic distribution data from the VIATOLL charging system) and data from the vehicle simulator.
- 16 November 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 231, 02008
Open AccessMethodology of research on the impact of ITS services on the safety and efficiency of road traffic using transport models
The current assessment of the impact of Intelligent Transport System (ITS) services on the level of traffic safety and efficiency is based mainly on expert assessments, statistical surveys or several traffic safety models requiring development. There is no structured, uniform assessment method that would give the opportunity to compare the impact of ITS services and their different configurations. The paper presents the methodology for researching the effectiveness of ITS services implementation using transport models and key indicators allowing such an assessment. An approach was used in which the impact of ITS services is analysed using macro, meso and microscopic models. Macro and mesoscopic models allow estimation of the impact of ITS services on the efficiency of transport network operation and constitute the basis of analyses at the microscopic level, which takes into account the behaviour of drivers through the use of car following and lane change models. As part of the analyses, road network test models (for motorways and expressways along with an alternative route) were developed. Test models include road class, network topology, and different traffic intensity. The models were calibrated using real data (data from the traffic measurement station, data measured in the field, traffic distribution data from the VIATOLL charging system) and data from the vehicle simulator.
- 6 September 2018
- Published by Springer Nature
- p. 142-156
Influence of Toll Collection Method on Motorways on Traffic Safety and Efficiency
- 6 September 2018
- Published by Springer Nature
- p. 142-156
Influence of Toll Collection Method on Motorways on Traffic Safety and Efficiency
- Open Access
- 10 August 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 122, 03008
Systematics of intelligent transport systems services
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry
- 10 August 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 122, 03008
Open AccessSystematics of intelligent transport systems services
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry
- Open Access
- 30 March 2017
- Published by Silesian University of Technology in Transport Problems
- Vol. 12 (1) , 39-50
ANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
- 30 March 2017
- Published by Silesian University of Technology in Transport Problems
- Vol. 12 (1) , 39-50
Open AccessANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
- Open Access
- 1 January 2016
- Published by Elsevier in Transportation Research Procedia
- Vol. 14, 3466-3475
Automatic Incident Detection at Intersections with Use of Telematics
- 1 January 2016
- Published by Elsevier in Transportation Research Procedia
- Vol. 14, 3466-3475
Open AccessAutomatic Incident Detection at Intersections with Use of Telematics