Hanguang Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hanguang Xie has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Vladimir Molkov
Hydrogen Safety Engineering and Research Centre (HySAFER), Ulster University, Newtownabbey BT37 0QB, UK
3 shared publications - Dmitriy Makarov
Hydrogen Safety Engineering and Research Centre (HySAFER), Ulster University, Newtownabbey BT37 0QB, UK
2 shared publications Gance Dai
2 shared publicationsJianguang Hu
2 shared publications- Sergii Kashkarov
Hydrogen Safety Engineering and Research Centre, Ulster University, Newtownabbey, BT37 0NL, Northern Ireland, UK
2 shared publications Cheng Wang
1 shared publication
Latest Publications
- Open Access
- 8 September 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 173
Thermal response of composite hydrogen tank and TPRD during fast fuelling
- 8 September 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 173
Open AccessThermal response of composite hydrogen tank and TPRD during fast fuelling
- Open Access
- 20 May 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 70, 715-728
Comparative analysis of CFD models to simulate temperature non-uniformity during hydrogen tank refuelling
- 20 May 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 70, 715-728
Open AccessComparative analysis of CFD models to simulate temperature non-uniformity during hydrogen tank refuelling
- Open Access
CFD Simulations of Hydrogen Tank Fuelling: Sensitivity to Turbulence Model and Grid Resolution
CFD modelling of compressed hydrogen fuelling provides information on the hydrogen and tank structure temperature dynamics required for onboard storage tank design and fuelling protocol development. This study compares five turbulence models to develop a strategy for cost-effective CFD simulations of hydrogen fuelling while maintaining a simulation accuracy acceptable for engineering analysis: RANS models k-ε and RSM; hybrid models SAS and DES; and LES model. Simulations were validated against the fuelling experiment of a Type IV 29 L tank available in the literature. For RANS with wall functions and blended models with near-wall treatment, the simulated average hydrogen temperatures deviated from the experiment by 1–3% with CFL ≈ 1–3 and dimensionless wall distance y+ ≈ 50–500 in the tank. To provide a similar simulation accuracy, the LES modelling approach with near-wall treatment requires mesh with wall distance y+ ≈ 2–10 and demonstrates the best-resolved flow field with larger velocity and temperature gradients. LES simulation on this mesh, however, implies a ca. 60 times longer CPU time compared to the RANS modelling approach and 9 times longer compared to the hybrid models due to the time step limit enforced by the CFL ≈ 1.0 criteria. In all cases, the simulated pressure histories and inlet mass flow rates have a difference within 1% while the average heat fluxes and maximum hydrogen temperature show a difference within 10%. Compared to LES, the k-ε model tends to underestimate and DES tends to overestimate the temperature gradient inside the tank. The results of RSM and SAS are close to those of LES albeit of 8–9 times faster simulations.
Open AccessCFD Simulations of Hydrogen Tank Fuelling: Sensitivity to Turbulence Model and Grid Resolution
CFD modelling of compressed hydrogen fuelling provides information on the hydrogen and tank structure temperature dynamics required for onboard storage tank design and fuelling protocol development. This study compares five turbulence models to develop a strategy for cost-effective CFD simulations of hydrogen fuelling while maintaining a simulation accuracy acceptable for engineering analysis: RANS models k-ε and RSM; hybrid models SAS and DES; and LES model. Simulations were validated against the fuelling experiment of a Type IV 29 L tank available in the literature. For RANS with wall functions and blended models with near-wall treatment, the simulated average hydrogen temperatures deviated from the experiment by 1–3% with CFL ≈ 1–3 and dimensionless wall distance y+ ≈ 50–500 in the tank. To provide a similar simulation accuracy, the LES modelling approach with near-wall treatment requires mesh with wall distance y+ ≈ 2–10 and demonstrates the best-resolved flow field with larger velocity and temperature gradients. LES simulation on this mesh, however, implies a ca. 60 times longer CPU time compared to the RANS modelling approach and 9 times longer compared to the hybrid models due to the time step limit enforced by the CFL ≈ 1.0 criteria. In all cases, the simulated pressure histories and inlet mass flow rates have a difference within 1% while the average heat fluxes and maximum hydrogen temperature show a difference within 10%. Compared to LES, the k-ε model tends to underestimate and DES tends to overestimate the temperature gradient inside the tank. The results of RSM and SAS are close to those of LES albeit of 8–9 times faster simulations.
- 7 June 2022
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 194
Asymmetric flow and mass transfer of twin-liquid films
- 7 June 2022
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 194
Asymmetric flow and mass transfer of twin-liquid films
- 1 April 2018
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 92, 174-183
Liquid flow transition and confined free film formation on a vertical plate with an open window
- 1 April 2018
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 92, 174-183
Liquid flow transition and confined free film formation on a vertical plate with an open window
- 22 November 2017
- Published by Wiley in AIChE Journal
- Vol. 64 (4) , 1458-1468
Numerical simulation on flow behavior of twin‐liquid films over a vertical plate with an open window
A novel element for gas–liquid contact, a plate with rectangular windows was designed to enhance absorption process. Coexistence and interaction of wall‐bounded films and confined free films named as “twin‐liquid films” were observed on the plate. Volume of fluid (VOF) method was used to simulate its flow behavior. Flow phenomena such as flow around a step‐in, jet impingement, varicose waves, and sinuous waves were observed. Different from thin films flow on an unperforated plate, larger mean velocity, thinner film thickness, more intensive capillary waves, and stronger vorticity on the free surfaces were detected inside the window, and the disturbances could propagate over the whole plate. Three‐dimensional simulation results generally agreed with our experimental observations and further demonstrated complex wavy structures both inside and outside the window. The results would broaden traditional knowledge of liquid films flow and clarify the mechanism of mass transfer intensification for the plate with windows. © 2017 American Institute of Chemical Engineers AIChE J, 64: 1458–1468, 2018
- 22 November 2017
- Published by Wiley in AIChE Journal
- Vol. 64 (4) , 1458-1468
Numerical simulation on flow behavior of twin‐liquid films over a vertical plate with an open window
A novel element for gas–liquid contact, a plate with rectangular windows was designed to enhance absorption process. Coexistence and interaction of wall‐bounded films and confined free films named as “twin‐liquid films” were observed on the plate. Volume of fluid (VOF) method was used to simulate its flow behavior. Flow phenomena such as flow around a step‐in, jet impingement, varicose waves, and sinuous waves were observed. Different from thin films flow on an unperforated plate, larger mean velocity, thinner film thickness, more intensive capillary waves, and stronger vorticity on the free surfaces were detected inside the window, and the disturbances could propagate over the whole plate. Three‐dimensional simulation results generally agreed with our experimental observations and further demonstrated complex wavy structures both inside and outside the window. The results would broaden traditional knowledge of liquid films flow and clarify the mechanism of mass transfer intensification for the plate with windows. © 2017 American Institute of Chemical Engineers AIChE J, 64: 1458–1468, 2018