Sathiesh Kumar Subramaniam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sathiesh Kumar Subramaniam has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
N. Neelakandeswari
Sri Ramakrishna Engineering College, Coimbatore, India
3 shared publicationsS. Aruna
Sardar Vallabhbhai Patel International School of Textiles & Management, Coimbatore, India
2 shared publications- Sundararajan Vairam
Department of Chemistry, Government College of Technology, Coimbatore, India
2 shared publications - Aruna Sampath
School of Chemical Engineering, Jimma Institute of Technology, Jimma University, Jimma, Ethiopia
1 shared publication - Ayano Koyrita Banale
Faculty of Material Science and Engineering, Jimma Institute of Technology, Jimma University, Jimma, Ethiopia
1 shared publication - Eba Mala Maldaye
Jimma Institute of Technology, Jimma University, Jimma, Ethiopia
1 shared publication
Latest Publications
- Open Access
- 1 October 2025
- Published by SAGE Publications in Nanomaterials and Nanotechnology
- Vol. 2025 (1)
Mechanistic and Kinetic Evaluation of Hexavalent Chromium Adsorption Using Polyaniline‐Functionalized Ti 3 C 2 T x MXene Composite
In the past few decades, different efforts have been made toward chromium (VI) removal from wastewater. In this study, a Ti 3 C 2 T x /PANI composite was synthesized via in situ polymerization from (PANI) and Mxene (Ti 3 C 2 T x ). The composite was characterized using XRD, FTIR, SEM–EDS, XPS, and Raman spectroscopy. FTIR spectra revealed characteristic functional groups of both Ti 3 C 2 T x and PANI, with significant shifts and intensity changes upon Cr(VI) adsorption. EDS and XPS also showed the presence of Cr after adsorption. Raman spectroscopy further verified PANI polymerization and Cr(VI) adsorption. The adsorption performance for Cr(VI) is markedly influenced by the pH level of the solution, with optimal adsorption occurring at an acidic pH. The experimental findings showed good agreement with the Langmuir–Freundlich and Khan isotherm models, while the pseudo‐second‐order and MESO kinetic models best describe the adsorption process. The Ti 3 C 2 T x /PANI composite exhibits a high adsorption capacity of 342.5 mg g −1 and good stability, maintaining its adsorption efficiency over seven cycles. The adsorption mechanism involves electrostatic attraction, surface complexation, and physical adsorption. Notably, the developed Ti 3 C 2 T x /PANI composite exhibits a considerably higher Cr(VI) adsorption capacity than most previously reported MXene (Ti 3 C 2 T x ) and polyaniline (PANI)‐based adsorbents. This superior performance is attributed to the synergistic interaction between the conductive polymer PANI and the high surface reactivity of Ti 3 C 2 T x layers, which enhances active site accessibility and electron transfer during adsorption. The findings demonstrate the composite’s potential as an efficient and robust adsorbent for Cr(VI) adsorption.
- 1 October 2025
- Published by SAGE Publications in Nanomaterials and Nanotechnology
- Vol. 2025 (1)
Open AccessMechanistic and Kinetic Evaluation of Hexavalent Chromium Adsorption Using Polyaniline‐Functionalized Ti 3 C 2 T x MXene Composite
In the past few decades, different efforts have been made toward chromium (VI) removal from wastewater. In this study, a Ti 3 C 2 T x /PANI composite was synthesized via in situ polymerization from (PANI) and Mxene (Ti 3 C 2 T x ). The composite was characterized using XRD, FTIR, SEM–EDS, XPS, and Raman spectroscopy. FTIR spectra revealed characteristic functional groups of both Ti 3 C 2 T x and PANI, with significant shifts and intensity changes upon Cr(VI) adsorption. EDS and XPS also showed the presence of Cr after adsorption. Raman spectroscopy further verified PANI polymerization and Cr(VI) adsorption. The adsorption performance for Cr(VI) is markedly influenced by the pH level of the solution, with optimal adsorption occurring at an acidic pH. The experimental findings showed good agreement with the Langmuir–Freundlich and Khan isotherm models, while the pseudo‐second‐order and MESO kinetic models best describe the adsorption process. The Ti 3 C 2 T x /PANI composite exhibits a high adsorption capacity of 342.5 mg g −1 and good stability, maintaining its adsorption efficiency over seven cycles. The adsorption mechanism involves electrostatic attraction, surface complexation, and physical adsorption. Notably, the developed Ti 3 C 2 T x /PANI composite exhibits a considerably higher Cr(VI) adsorption capacity than most previously reported MXene (Ti 3 C 2 T x ) and polyaniline (PANI)‐based adsorbents. This superior performance is attributed to the synergistic interaction between the conductive polymer PANI and the high surface reactivity of Ti 3 C 2 T x layers, which enhances active site accessibility and electron transfer during adsorption. The findings demonstrate the composite’s potential as an efficient and robust adsorbent for Cr(VI) adsorption.
- Open Access
- 9 May 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (5) , 1-14
Designs and materials of flexible wearable microstrip patch antennas: a systematic review
- 9 May 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (5) , 1-14
Open AccessDesigns and materials of flexible wearable microstrip patch antennas: a systematic review
- 23 November 2024
- Published by World Scientific Pub Co Pte Ltd in Nano
- Vol. 20 (05)
Characterization and Synthesis of Graphite, Graphene Oxide, and Reduced Graphene Oxide Powder from Waste Dry Cell Battery Rod
In this paper, graphite, graphene oxide, and reduced graphene powders were successfully synthesized from waste dry cell batter through successive chemical solution methods. Graphite powder was extracted from the graphite electrode of waste batteries rod by acidic chemical treatment. The obtained powder was utilized as a precursor for synthesizing graphene oxide following the new modified Tour method. Eventually, reduced graphene oxide was prepared from the chemical reduction of graphene oxide (GO) by hydrazine hydrate treatment. The obtained recycled graphite, reduced graphene oxide (rGO), and GO materials have been characterized using scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction (XRD), photoluminescence (PL), and Raman spectroscopy effectively. All the above characterization results confirmed that graphite shows a strong peak at a diffraction angle of 26.5°, corresponding to the (002) plane, shifted to a lower angle of 25.2° in the case of rGO. In addition, the unsmooth graphite sheet shifted to smooth and flake-like shape of the rGO’s surface morphology. The composite result revealed that different amounts of oxygen and carbon atoms are present in rG, GO and rGO. All the experimental findings ultimately launch the successful formation of exfoliated rGO and better synthesis approach was achieved.
- 23 November 2024
- Published by World Scientific Pub Co Pte Ltd in Nano
- Vol. 20 (05)
Characterization and Synthesis of Graphite, Graphene Oxide, and Reduced Graphene Oxide Powder from Waste Dry Cell Battery Rod
In this paper, graphite, graphene oxide, and reduced graphene powders were successfully synthesized from waste dry cell batter through successive chemical solution methods. Graphite powder was extracted from the graphite electrode of waste batteries rod by acidic chemical treatment. The obtained powder was utilized as a precursor for synthesizing graphene oxide following the new modified Tour method. Eventually, reduced graphene oxide was prepared from the chemical reduction of graphene oxide (GO) by hydrazine hydrate treatment. The obtained recycled graphite, reduced graphene oxide (rGO), and GO materials have been characterized using scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction (XRD), photoluminescence (PL), and Raman spectroscopy effectively. All the above characterization results confirmed that graphite shows a strong peak at a diffraction angle of 26.5°, corresponding to the (002) plane, shifted to a lower angle of 25.2° in the case of rGO. In addition, the unsmooth graphite sheet shifted to smooth and flake-like shape of the rGO’s surface morphology. The composite result revealed that different amounts of oxygen and carbon atoms are present in rG, GO and rGO. All the experimental findings ultimately launch the successful formation of exfoliated rGO and better synthesis approach was achieved.
- Open Access
- 4 July 2023
- Published by Wiley in Journal of Nanomaterials
- Vol. 2023, 1-7
Fabrication of Visible Light Sensitive Electrospun TiO2 Nanofibers Using Squaric Acid for Photocatalytic Application
Degradation of organic pollutants using photocatalysts has gained utmost importance, due to the increasing environmental pollution. Despite various attempts to improve the photocatalytic efficiency of well-known photocatalysts such as titanium dioxide (TiO2), by making them visible light active, various issues need to be resolved. In this work, attempts have been made to improve the visible light absorption capacities of the electrospun TiO2 nanofibers by modification using squaric acid (SqA). An interfacial charge transfer complex is formed by the condensation reaction between the hydroxyl groups on the surface of the TiO2 nanofibers and the SqA ligand. Various characterizations confirmed that the modification using SqA had led to the formation of the interfacial charge transfer layer, without affecting the crystallinity or morphology of the TiO2 nanofibers. The modified TiO2 nanofibers showed sensitivity to visible light with red shift in the optical absorption. It exhibited an improved photocatalytic efficiency of 85 against the degradation of tetracycline, compared with 60 for unmodified TiO2 nanofibers. It also showed an increased rate of degradation of 0.21mg/L/min, when compared with the 0.13mg/L/min of unmodified TiO2 nanofibers.
- 4 July 2023
- Published by Wiley in Journal of Nanomaterials
- Vol. 2023, 1-7
Open AccessFabrication of Visible Light Sensitive Electrospun TiO2 Nanofibers Using Squaric Acid for Photocatalytic Application
Degradation of organic pollutants using photocatalysts has gained utmost importance, due to the increasing environmental pollution. Despite various attempts to improve the photocatalytic efficiency of well-known photocatalysts such as titanium dioxide (TiO2), by making them visible light active, various issues need to be resolved. In this work, attempts have been made to improve the visible light absorption capacities of the electrospun TiO2 nanofibers by modification using squaric acid (SqA). An interfacial charge transfer complex is formed by the condensation reaction between the hydroxyl groups on the surface of the TiO2 nanofibers and the SqA ligand. Various characterizations confirmed that the modification using SqA had led to the formation of the interfacial charge transfer layer, without affecting the crystallinity or morphology of the TiO2 nanofibers. The modified TiO2 nanofibers showed sensitivity to visible light with red shift in the optical absorption. It exhibited an improved photocatalytic efficiency of 85 against the degradation of tetracycline, compared with 60 for unmodified TiO2 nanofibers. It also showed an increased rate of degradation of 0.21mg/L/min, when compared with the 0.13mg/L/min of unmodified TiO2 nanofibers.
- 2 June 2020
- Published by Springer Nature in Carbon Letters
- Vol. 31 (1) , 125-136
Effect of graphene addition on the mechanical characteristics of AA7075 aluminium nanocomposites
- 2 June 2020
- Published by Springer Nature in Carbon Letters
- Vol. 31 (1) , 125-136
Effect of graphene addition on the mechanical characteristics of AA7075 aluminium nanocomposites
- 1 June 2018
- Published by Elsevier in Materials Letters
- Vol. 220, 249-252
Effect of metal oxide charge transfer layers on the photovoltaic performance of carbon nanotube heterojunction solar cells
- 1 June 2018
- Published by Elsevier in Materials Letters
- Vol. 220, 249-252
Effect of metal oxide charge transfer layers on the photovoltaic performance of carbon nanotube heterojunction solar cells
- 1 June 2018
- Published by Elsevier in Materials Letters
- Vol. 220, 218-221
Synthesis and characterisation of SnO 2 nanostructures for Dye-Sensitized Solar Cells
- 1 June 2018
- Published by Elsevier in Materials Letters
- Vol. 220, 218-221
Synthesis and characterisation of SnO 2 nanostructures for Dye-Sensitized Solar Cells
- 1 May 2018
- Published by Elsevier in Solar Energy
- Vol. 166, 195-202
New heterojunction solar cells using copper oxide ingrained MWCNT: Fabrication and performance analysis
- 1 May 2018
- Published by Elsevier in Solar Energy
- Vol. 166, 195-202
New heterojunction solar cells using copper oxide ingrained MWCNT: Fabrication and performance analysis
- 1 January 2014
- Published by Springer Nature
- p. 456-459
Carbon Nanotubes as a Cradle of Impulse for Implantable Medical Devices
- 1 January 2014
- Published by Springer Nature
- p. 456-459
Carbon Nanotubes as a Cradle of Impulse for Implantable Medical Devices