ABAfarulrazi Abu Bakar

Afarulrazi Abu Bakar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Afarulrazi Abu Bakar has a total of 90 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Design of 7-level cascade asymmetric multilevel inverter for renewable energy applications using FPGA

    by Afarulrazi Abu Bakar, Hazwaj Mhd Poad, Benjamin Ho Hao Xian, Tharnisha Sithananthan, Wahyu Mulyo Utomo, Triyanto Pangaribowo

    The increasing focus on renewable energy has driven the need for efficient and reliable power converters. Multilevel inverters offer low harmonic distortion and high-quality output but often suffer from design complexity and excessive component count. This study presents the design and implementation of a 7-level cascaded asymmetric multilevel inverter optimized for renewable energy applications. The proposed topology utilizes a cascade structure with asymmetric DC voltage sources to generate seven voltage levels, providing a practical balance between performance and simplicity. The design was first validated through MATLAB/Simulink software to analyze circuit operation and evaluate the total harmonic distortion (THD) performance. Experimental evaluation was then conducted using a hardware prototype to verify simulation results. Without a filter, the THD from the simulation was 21.31%, while the experimental setup recorded a slightly higher value of 21.61%, indicating a marginal difference of 0.21%. With a filter, the simulation achieved a THD of 3.81%, whereas the experimental setup outperformed with a THD of 1.5%, showing a notable reduction of 2.31%. These findings confirm the proposed inverter’s capability to deliver superior power quality and operational efficiency. The combination of simulation and experimental validation demonstrates the practicality and reliability of the 7-level cascade asymmetric multilevel inverter for renewable energy applications.

  • Open Access

    Field-programmable gate array-based voltage-feedback-driven battery charging with DC-DC buck converter

    by Afarulrazi Abu Bakar, Suhaimi Saiman, Tharnisha Sithananthan, Muhammad Nafis Ismail, Saidina Hamzah Che Harun

    This paper presents the design and development of a reference-driven field-programmable gate array (FPGA)-based controllable battery charging system featuring a buck converter. The controller tracks and adjusts the system's duty cycle based on output voltage feedback. The primary goal was to introduce a digital pulse-width modulation generator program using a Hardware Description Language within a feedback loop. To enhance the buck converter's accuracy, the system's switching frequency was set to 20 kHz with an 8-bit counter, achieving a resolution of 0.390625% per clock cycle. An 8-bit parallel analog-to-digital converter provided feedback by measuring the output voltage and comparing it with the reference setpoint. The simulation model was developed using MATLAB/Simulink, while the Quartus II software was employed for controller programming. The resultant data was meticulously analyzed to assess the circuit's performance across various voltage and control parameters. To validate the proposed controller's effectiveness, a 400 W system prototype comprising a step-down transformer, rectifier, and buck converter was constructed and tested for voltage ranging from 24 to 72 V. Through FPGA-based digital control, this system demonstrated a voltage regulation accuracy of ±0.39 per clock cycle and the capability to continuously track and regulate the duty cycle with each clock trigger, ensuring precise control over the charging process.

  • Open Access

    Digitally fast synchronization of single-phase grid-tied inverter using FPGA

    by Afarulrazi Abu Bakar, Balarajan Sannasy, Hazwaj Mhd Poad, Tharnisha Sithananthan, Wahyu Mulyo Utomo, Nor Farisha Diana Rosli

    As interest in alternative energy sources grows, grid-connected inverters are getting more advanced. Thus, to synchronize the output waveform of an inverter with the grid supply system, the frequency and phase angle ought to be consistent. This paper presents an enhanced digital implementation controller for a grid-connected inverter using the sinusoidal pulse-width modulation (SPWM) switching technique via an appropriately designed low-pass filter. The main contribution of the proposed digital controller algorithm is to synchronize with the grid for the next half-cycle. The proposed control technique used the integrated response from the zero-crossing detector (ZCD) circuit for every half-cycle to trigger the digital phase-locked loop (PLL) implemented using field-programmable gate array (FPGA). An experimental 100 W single-phase full-bridge inverter prototype tested and validated the proposed control algorithm to prove the switching approach works. From the experimental results, the proposed control algorithm demonstrates synchronization with the grid voltage within 8 ms during startup. Furthermore, it exhibits the ability to adapt to phase changes when subjected to a distorted grid, achieving synchronization within 42 ms. This research also emphasizes synchronization between the grid waveform and the inverter output via the phase angle difference.


  • Open Access

    Enhancing voltage stability through wavelet-fuzzy control of hydrogen flow in OC-PEM fuel cell

    by Triyanto Pangaribowo, Wahyu Mulyo Utomo, Abdul Hamid Budiman, Afarulrazi Abu Bakar, Deni Shidqi Khaerudini

    Open cathode proton exchange membrane fuel cells (OC-PEM fuel cells) serve as electricity generators, utilizing hydrogen as an input source. While effective for fixed loads like residential applications, challenges arise in dealing with output voltage fluctuations caused by rapid load changes. These fluctuations not only impact fuel cell performance but also introduce instability in the supplied power. To solve this issue, the study proposes an innovative hydrogen flow control system employing a feedforward wavelet- fuzzy method. The primary goal of this control system is to enhance fuzzy control performance using wavelets, mitigating signal fluctuations and achieving optimal stability in fuel cell output voltage under constant load conditions. Wavelet functions act as filters on the fuzzy control input, minimizing fluctuations and refining the entire process. Additionally, a feedforward system is incorporated to maintain hydrogen flow at the set point value. The proposed control system is implemented on a validated model using experimental data. Performance analysis reveals that the proposed method effectively stabilizes voltage by accelerating the recovery time from disturbances.


  • Open Access

    Power converter for battery charger of electric vehicle with controllable charging current

    by Suroso Suroso, Hari Prasetijo, Winasis Winasis, Hari Siswantoro, Daru Tri Nugroho, Wahyu Mulyo Utomo, Afarulrazi Abu Bakar

    Research on electric vehicle chargers primarily focuses on improving charging technology to enhance the convenience, quality, efficiency, and affordability of charging electric vehicles. This paper discusses a different AC-DC power converter topology proposed as a potential candidate for electric vehicle battery charger. Using the proposed converter circuit, the charging process of electric vehicle battery can be simply adjusted to meet the battery requirement, and even for increasing the charging speed while avoiding overcharging of battery. During the charging process, if the voltage of battery approaches to the targeted battery voltage level, the charging current can be reduced gradually to zero. Hence it will prevent the battery from overcharging condition. Moreover, the ability of working at high power factor operation, low distortion of alternating current (AC) input current, and low direct current (DC) output current ripple are other features of the proposed charger circuits. Some test results of the proposed power converter were presented. The test results revealed potential features of the converter for battery charger of electric vehicle with power factor 0.9996, total harmonic distortion (THD) of AC current 2.73%, and low charging current ripple, i.e. 3.91%. Therefore, it minimizes the negative effects caused by ripples of charging current especially for lithium-ion batteries widely used in electric vehicles.


  • Open Access

    Fast synchronization with enhanced switching control for grid-tied single-phase square wave inverter using FPGA

    by Tharnisha Sithananthan, Afarulrazi Abu Bakar, Balarajan Sannasy, Wahyu Mulyo Utomo, Taufik Taufik

    Research on grid synchronization has been conducted worldwide by researchers in conjunction with the development of innovative technologies, such as dedicated short-range communication (DSRC) and cellular vehicle-to-everything (C-V2X). However, grid-connected inverters face several challenges, mainly the mismatch in voltage amplitude, frequency, and phase angle, as well as grid voltage disturbance and grid faults. Thus, the control algorithm of this research mainly focused on a half-cycle algorithm to design an enhanced digital switching control for fast synchronization using an FPGA. The control algorithm was developed based on zero-crossing detection (ZCD) and digital phase-locked loop (PLL) modeling techniques using the hardware description language (HDL) and a combination of digital logic blocks in Quartus II software, where the proposed switching was applied using the square-wave switching technique through a 300-watt full-bridge experimental prototype. The performance of the proposed technique was studied, where the total harmonic distortion (THD) for voltage and current resulted in a percentage reduction of 89.29% and 78.05% for voltage and current, respectively, after filter implementation. Also, the resulting signal synchronized in every half cycle and matched the voltage amplitude, frequency, and phase angle of the grid signal in 10 ms.


  • Open Access

    Power losses analysis of multiphase DC-DC buck converter using OrCAD PSpice software

    by Ahmad Faiz Abdul Ghani, Mhd Hazwaj Poad, Afarulrazi Abu Bakar, Siti Nuraini Norazman, Mohd Azlee Noor Amran

    DC-DC buck converters have wide applications in portable electronic devices, battery chargers, and telecommunications. However, single-phase DC-DC buck converters have some drawbacks, especially in high current applications, where the increase in the size of the inductor will increase power losses, which significantly affects the overall efficiency of the converter. The multiphase configuration offers several advantages, such as reduction in output voltage ripple, input current ripple, conduction loss, and the physical size of the hardware. This paper presents an analysis of the power losses of the multiphase DC-DC buck converter with output power ranging between 50 watts to 250 watts. To verify the effectiveness of the multiphase converter, performance analysis was done using OrCAD PSpice software, where the number of phases was limited to five phases. This paper focused on power losses in the converter, namely conduction losses in diodes and MOSFETs, switching loss in MOSFETs, as well as losses in the inductor and capacitor. The relationship between the number of phases and factors of switching frequency, output, and the components’ internal resistance was also highlighted and discussed in detail.

  • Open Access

    Decentralized Virtual Impedance-based Circulating Current Suppression Control for Islanded Microgrids

    by A. Abu Bakar, E. Pathan, M. K. Khan, M. A. Sadiq, M. I. Rabani, S. B. Goli, F. Pathan, M. A. Shaikh

    Parallel connected inverters in islanded mode, are getting momentous attention due to their ability to increase the power distribution and reliability of a power system. When there are different ratings of Distributed Generation (DG) units, they will operate in parallel connection due to different output voltages, impedance mismatch, or different phase that can cause current to flow between DG units. The magnitude of this circulating current sometimes can be very large and damage the DG inverters and also cause power losses that affect power-sharing accuracy, power quality, and the efficiency of the Microgrid (MG) system. Droop control, improved droop control, and virtual impedance control techniques and modifications in the virtual impedance control technique are widely used to suppress the circulating current. However, the addition of the virtual impedance to each inverter to compensate the output impedance is resistive or inductive in nature. The resistive nature of the output impedance always causes a certain voltage drop, whereas the inductive nature of the output impedance causes phase delay for the output voltage. Both problems are addressed by the proposed control mechanism in this paper. Negative resistance, along with virtual impedance, is utilized in the proposed control strategy. The output impedance is to be maintained as inductive in nature to achieve good load sharing in droop control MGs. The simulation results validate the proposed control scheme.


  • Open Access

    A Robust Frequency Controller based on Linear Matrix Inequality for a Parallel Islanded Microgrid

    by E. Pathan, A. Abu Bakar, S. A. Zulkifi, M. H. Khan, H. Arshad, M. Asad

    This paper presents a robust H∞ control technique for an islanded microgrid in the presence of sudden changes in load conditions. The proposed microgrid scheme consists of a parallel connected inverter with distributed generations. When the load is suddenly changed the frequency deviates from its nominal value. The objective is to design a robust frequency droop controller in order to achieve the frequency at nominal values without using any secondary controller and communication systems while improving power sharing accuracy. Small signal modeling of the power system is designed for the formulation of the problem and the H∞ optimal linear matrix inequality technique is applied in order to achieve the objectives. The proposed controller has been tested with the MATLAB/ SimPowerSytem toolbox.


  • Open Access

    Simulation and modeling of two-level DC/DC boost converter using ARX, ARMAX, and OE model structures

    by M.A.N. Amran, A.A. Bakar, M.H.A. Jalil, M.U. Wahyu, A.F.H.A. Gani

    This paper presents simulation and modeling of two-level DC/DC boost converter using system identification technique. The main objective is to identify the unknown mathematical model from designated converter that has 2 modes of operation. Signals from the converter were processed based on the impulse response from input and output voltages, which were in time domain data. Auto Regressive with eXogenous (ARX), Auto Regressive Moving Average with eXogenous (ARMAX), and Output-Error (OE) model structure techniques had been employed to generate a model from the converter, whose validation was based on coefficient of determination (R2) or best fits criterion. The result shows that the ARX model structure produced the best model with 94.03%, compared to ARMAX and OE with 93.70% and 92.25% respectively. In terms of stability for open-loop analysis, the ARX model structure gave the most stable system.