Augustin Gakwaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Augustin Gakwaya has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Charles-Olivier Amyot
Department of Mechanical Engineering, Université Laval, Quebec, Canada
1 shared publicationD. Nandlall
1 shared publicationEmna Ghazali
Department of Mechanical Engineering, Université Laval, Quebec, Canada
1 shared publication- Julie Lévesque
Québec Metallurgy, Center Trois-Rivières, Québec, Canada
1 shared publication - Kadiata Ba
Department of Applied Science Université du Québec à Chicoutimi, Chicoutimi, Quebec, Canada
1 shared publication L. M. Kamoso
Laval University
1 shared publication
Latest Publications
- Open Access
- 16 June 2025
- Published by IOS Press
- p. 638-644
Residual Stress Evolution During the Manufacturing of an Aircraft Component
This paper proposes a comprehensive analysis of the evolution of the surface residual stress state over the manufacturing stages of generic forged aircraft components. This has been achieved through an experimental procedure, involving forging of the generic component preforms, heat treatments, and machining operations on Computer Numerical Control milling and lathe centers. Surface residual stresses were measured using X-ray diffraction technique. The results showed a high scatter of surface residual stress measured in the same zone although the machining was done by the same cutting tool and under the same machining conditions. This suggests that the residual stress measured at a specific zone is significantly sensitive to previous and further major material removal such as rough pocketing the components have underwent. Moreover, it was found that the quenching and aging heat treatment drastically modify, not only the machining induced-residual stress state, but also the physical surface characteristics as demonstrated by the shear to normal residual stress ratio and the full width at half maximum of the X-ray diffraction peaks. Conclusively, the findings of this work help both researchers and manufacturers to better understand the challenges related to the design and the manufacturing of structural aircraft components made from forgings.
- 16 June 2025
- Published by IOS Press
- p. 638-644
Open AccessResidual Stress Evolution During the Manufacturing of an Aircraft Component
This paper proposes a comprehensive analysis of the evolution of the surface residual stress state over the manufacturing stages of generic forged aircraft components. This has been achieved through an experimental procedure, involving forging of the generic component preforms, heat treatments, and machining operations on Computer Numerical Control milling and lathe centers. Surface residual stresses were measured using X-ray diffraction technique. The results showed a high scatter of surface residual stress measured in the same zone although the machining was done by the same cutting tool and under the same machining conditions. This suggests that the residual stress measured at a specific zone is significantly sensitive to previous and further major material removal such as rough pocketing the components have underwent. Moreover, it was found that the quenching and aging heat treatment drastically modify, not only the machining induced-residual stress state, but also the physical surface characteristics as demonstrated by the shear to normal residual stress ratio and the full width at half maximum of the X-ray diffraction peaks. Conclusively, the findings of this work help both researchers and manufacturers to better understand the challenges related to the design and the manufacturing of structural aircraft components made from forgings.
- 1 June 2018
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 116, 22-33
On the determination of the shock and steady state parameters of gelatine from cylinder impact experiments
- 1 June 2018
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 116, 22-33
On the determination of the shock and steady state parameters of gelatine from cylinder impact experiments
- Open Access
- 3 July 2017
- Published by SAGE Publications in Journal of Sandwich Structures & Materials
- Vol. 21 (4) , 1357-1378
Mechanical performance of repaired sandwich panels: Experimental characterization and finite-element modelling
This paper describes the static performance of adhesively bonded repairs on sandwich panels made with carbon-epoxy composite skins and a Nomex core. First, the mechanical behaviour of pristine and repaired panels under tensile loading was studied. All tests were conducted under room temperature conditions. Then, finite-element analyses were performed to predict the behaviour of repaired panels. Two material models were developed for the adhesive joint: one was linear elastic and the second was elastic-plastic with a shear failure criterion. For the composite skins, an orthotropic linear elastic model was used. Numerical model predictions are in good agreement with the experimental results. It was found also that the strength recovery of the repaired structure increases with the decrease of the scarf angle.
- 3 July 2017
- Published by SAGE Publications in Journal of Sandwich Structures & Materials
- Vol. 21 (4) , 1357-1378
Open AccessMechanical performance of repaired sandwich panels: Experimental characterization and finite-element modelling
This paper describes the static performance of adhesively bonded repairs on sandwich panels made with carbon-epoxy composite skins and a Nomex core. First, the mechanical behaviour of pristine and repaired panels under tensile loading was studied. All tests were conducted under room temperature conditions. Then, finite-element analyses were performed to predict the behaviour of repaired panels. Two material models were developed for the adhesive joint: one was linear elastic and the second was elastic-plastic with a shear failure criterion. For the composite skins, an orthotropic linear elastic model was used. Numerical model predictions are in good agreement with the experimental results. It was found also that the strength recovery of the repaired structure increases with the decrease of the scarf angle.
- 1 January 1992
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 10 (1) , 1-15
A boundary element formulation for the thermo-elastohydrodynamic contact problems Part I: theory
- 1 January 1992
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 10 (1) , 1-15
A boundary element formulation for the thermo-elastohydrodynamic contact problems Part I: theory
- 1 January 1991
- Published by Springer Nature
- p. 705-716
Integrated Computer Aided Surface Modeling and BEM Analysis
- 1 January 1991
- Published by Springer Nature
- p. 705-716
Integrated Computer Aided Surface Modeling and BEM Analysis