Alex Francis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Alex Francis has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Ilya Avdeev
University of Wisconsin-Milwaukee, Milwaukee, WI
3 shared publicationsC. S. Garnett
University of Wisconsin-Milwaukee, Milwaukee, WI
1 shared publicationCalvin Berceau
DRS Power and Control Technologies, Milwaukee, WI
1 shared publicationD. K. Patel
University of Wisconsin-Milwaukee, Milwaukee, WI
1 shared publicationDaniel Bautista
University of Wisconsin-Milwaukee, Milwaukee, WI
1 shared publicationE. Y. A. Wornyoh
University of Wisconsin-Milwaukee, Milwaukee, WI
1 shared publication
Latest Publications
- 11 November 2016
- Published by ASME International
Progress Toward Understanding Catastrophic Failure of Electric Vehicle Li-Ion Batteries: Multi-Physics Modeling
The goal of this work is to enhance understanding of critical design aspects that would prevent automotive lithium-ion battery packs from catastrophic failures. Modeling lithium-ion batteries is a complex multiscale multi-physics problem. The most dangerous energy producing component of a lithium ion cylindrical cell, jellyroll, is a layered spiral structure, which consists of thin layers of electrodes and separator only microns thick. In this study, we investigate the feasibility of using commercial explicit finite element code LS-DYNA to understand the structural integrity of lithium-ion batteries subjected to crushing condition through computer simulation. The jellyroll was treated as homogeneous material with an effective stress-strain curve obtained through characterization experiments of representative jellyroll samples and individual electrode layers. Physical and numerical impact tests have been conducted on cylindrical cells using developed drop test system. Results of material homogenization, experimental drop testing, and initial structural simulations are discussed. The investigation of structural cell deformations coupled with thermal heat generation and distribution after the crash brings us one step closer to accurate modeling of the entire battery pack that consists of hundreds of cells.
- 11 November 2016
- Published by ASME International
Progress Toward Understanding Catastrophic Failure of Electric Vehicle Li-Ion Batteries: Multi-Physics Modeling
The goal of this work is to enhance understanding of critical design aspects that would prevent automotive lithium-ion battery packs from catastrophic failures. Modeling lithium-ion batteries is a complex multiscale multi-physics problem. The most dangerous energy producing component of a lithium ion cylindrical cell, jellyroll, is a layered spiral structure, which consists of thin layers of electrodes and separator only microns thick. In this study, we investigate the feasibility of using commercial explicit finite element code LS-DYNA to understand the structural integrity of lithium-ion batteries subjected to crushing condition through computer simulation. The jellyroll was treated as homogeneous material with an effective stress-strain curve obtained through characterization experiments of representative jellyroll samples and individual electrode layers. Physical and numerical impact tests have been conducted on cylindrical cells using developed drop test system. Results of material homogenization, experimental drop testing, and initial structural simulations are discussed. The investigation of structural cell deformations coupled with thermal heat generation and distribution after the crash brings us one step closer to accurate modeling of the entire battery pack that consists of hundreds of cells.
- 11 November 2016
- Published by ASME International
Phantom Battery Pack for Destructive Testing of Li-Ion Batteries
The objective of this study is to find a structural alternative to jellyroll in order to safely conduct experimental crash testing of lithium-ion battery packs in academic laboratory environment. A procedure for lateral impact experiments has been developed and conducted on cylindrical cells and phantom cells using a flat rigid drop cart in a custom-built impact test apparatus. The main component of a cylindrical cell, jellyroll, is a layered spiral structure which consists of thin layers of electrodes and separator material. We investigate various phantom materials — candidates to replace the layered jellyroll with a homogeneous anisotropic material. During our experimentation with various phantom cells, material properties and internal geometries of additively manufactured components such as in-fill pattern, density and voids were adjusted in order to develop accurate deformation response. The deformation of the phantom cell was characterized and compared after impact testing with the actual lithium-ion cells. The experimental results were also compared with explicit simulations (LS-DYNA). This work shows progress toward an accurate and safe experimental procedure for structural impact testing on the entire battery pack consisting of thousands of volatile cells. Understanding battery and battery pack structural response can influence design and improve safety of electric vehicles.
- 11 November 2016
- Published by ASME International
Phantom Battery Pack for Destructive Testing of Li-Ion Batteries
The objective of this study is to find a structural alternative to jellyroll in order to safely conduct experimental crash testing of lithium-ion battery packs in academic laboratory environment. A procedure for lateral impact experiments has been developed and conducted on cylindrical cells and phantom cells using a flat rigid drop cart in a custom-built impact test apparatus. The main component of a cylindrical cell, jellyroll, is a layered spiral structure which consists of thin layers of electrodes and separator material. We investigate various phantom materials — candidates to replace the layered jellyroll with a homogeneous anisotropic material. During our experimentation with various phantom cells, material properties and internal geometries of additively manufactured components such as in-fill pattern, density and voids were adjusted in order to develop accurate deformation response. The deformation of the phantom cell was characterized and compared after impact testing with the actual lithium-ion cells. The experimental results were also compared with explicit simulations (LS-DYNA). This work shows progress toward an accurate and safe experimental procedure for structural impact testing on the entire battery pack consisting of thousands of volatile cells. Understanding battery and battery pack structural response can influence design and improve safety of electric vehicles.
- 14 November 2014
- Published by ASME International
Model Order Reduction for Design of Torsional Disk Couplings
Torsional couplings are used to transmit power between various rotating components of power systems while allowing for relatively small misalignments that may otherwise lead to equipment failure. When selecting a proper coupling type and size, one has to consider three important conditions: (1) maximum load applied to the coupling, (2) maximum operation speed and (3) amount of misalignment allowable for normal operation. There are many types of flexible couplings that use various materials for the flexible element of the coupling on the market today. Design of the coupling and the materials used for the flexible elements determine the coupling’s operating characteristics. In this project, we study metal disk couplings. Benefits of this type of coupling include: ease of replacement or repair, clear visual feedback of element failure, and the absence of a need for lubrication. The torsional stiffness of a coupling is a major factor relative to the amount of misalignment allowable. Currently, flexible couplings are tested by manufacturers to experimentally determine the torsional stiffness; a process which requires expensive equipment and more importantly employee time to set-up and run. The torsional coupling lumped characteristics, such as torsional- and flexural stiffness, as well as natural frequencies are important for design of the entire power system and have to be as precise as possible. In this work, we have developed an accurate modeling framework for determining these parameters based on a full 3-D finite element model and model-order reduction procedure. Developed methodology was validated by available experimental data from one of the leading manufacturers of torsional couplings.
- 14 November 2014
- Published by ASME International
Model Order Reduction for Design of Torsional Disk Couplings
Torsional couplings are used to transmit power between various rotating components of power systems while allowing for relatively small misalignments that may otherwise lead to equipment failure. When selecting a proper coupling type and size, one has to consider three important conditions: (1) maximum load applied to the coupling, (2) maximum operation speed and (3) amount of misalignment allowable for normal operation. There are many types of flexible couplings that use various materials for the flexible element of the coupling on the market today. Design of the coupling and the materials used for the flexible elements determine the coupling’s operating characteristics. In this project, we study metal disk couplings. Benefits of this type of coupling include: ease of replacement or repair, clear visual feedback of element failure, and the absence of a need for lubrication. The torsional stiffness of a coupling is a major factor relative to the amount of misalignment allowable. Currently, flexible couplings are tested by manufacturers to experimentally determine the torsional stiffness; a process which requires expensive equipment and more importantly employee time to set-up and run. The torsional coupling lumped characteristics, such as torsional- and flexural stiffness, as well as natural frequencies are important for design of the entire power system and have to be as precise as possible. In this work, we have developed an accurate modeling framework for determining these parameters based on a full 3-D finite element model and model-order reduction procedure. Developed methodology was validated by available experimental data from one of the leading manufacturers of torsional couplings.
- 17 October 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 23 (1) , 315-325
Rate- and Temperature-Dependent Material Behavior of a Multilayer Polymer Battery Separator
- 17 October 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 23 (1) , 315-325
Rate- and Temperature-Dependent Material Behavior of a Multilayer Polymer Battery Separator
- 9 November 2012
- Published by ASME International
- p. 475-481
Materials Testing of a Lithium Ion Battery Separator for Use in Finite Element Analysis
The use of lithium-ion batteries in the automotive industry has become increasingly popular. As more hybrid and electric vehicles take to the road an understanding of how these batteries will behave structurally will be of greater concern. Impact testing can give a valuable overview of the strengths and weaknesses of a batteries design, however, these tests can be time consuming, expensive, and dangerous. Finite element analysis can deliver a reliable low cost approximation of physical testing results. The accuracy of FE results depends greatly on the mathematical representation of the material properties of Li-ion battery components. In this study, the material properties of polymer thin film used as a separator between an anode and a cathode are tested experimentally under various temperatures and strain rates. Experimental results were used to develop a constitutive model for semi-crystalline polymers that is well suited for the finite element analysis.
- 9 November 2012
- Published by ASME International
- p. 475-481
Materials Testing of a Lithium Ion Battery Separator for Use in Finite Element Analysis
The use of lithium-ion batteries in the automotive industry has become increasingly popular. As more hybrid and electric vehicles take to the road an understanding of how these batteries will behave structurally will be of greater concern. Impact testing can give a valuable overview of the strengths and weaknesses of a batteries design, however, these tests can be time consuming, expensive, and dangerous. Finite element analysis can deliver a reliable low cost approximation of physical testing results. The accuracy of FE results depends greatly on the mathematical representation of the material properties of Li-ion battery components. In this study, the material properties of polymer thin film used as a separator between an anode and a cathode are tested experimentally under various temperatures and strain rates. Experimental results were used to develop a constitutive model for semi-crystalline polymers that is well suited for the finite element analysis.
- 1 January 2011
- Published by ASME International
- p. 245-247
Improving Rolling Element Bearing Thermal Compliance Through In Situ Cooling
In this study a novel in situ rolling element bearing (REB) lubricant cooling system is developed that provides a continuous cooling of the bearing outer race. In the design the stationary outer race is expanded to accommodate a cooling coil for the continuous cooling of the lubricant and the outer race. Water is used as the coolant While Amsoil 75W-90 Severe Gear® oil is used as a lubricant. Heat generated during the test run is removed by the coolant flowing through the cooling coil. The tribological effects at the speeds of the cooling test were evaluated using block-on-ring tribometer tests. Results from the experiments indicate that in the absence of cooling the temperature of the bearing outer race rises while cooling dramatically lowers the temperature. Also, the coefficient of friction increases with increasing speed. As such, in situ cooling that leads to reduced operational temperature minimizes lubricant degradation that can result from uncontrolled frictional heating.
- 1 January 2011
- Published by ASME International
- p. 245-247
Improving Rolling Element Bearing Thermal Compliance Through In Situ Cooling
In this study a novel in situ rolling element bearing (REB) lubricant cooling system is developed that provides a continuous cooling of the bearing outer race. In the design the stationary outer race is expanded to accommodate a cooling coil for the continuous cooling of the lubricant and the outer race. Water is used as the coolant While Amsoil 75W-90 Severe Gear® oil is used as a lubricant. Heat generated during the test run is removed by the coolant flowing through the cooling coil. The tribological effects at the speeds of the cooling test were evaluated using block-on-ring tribometer tests. Results from the experiments indicate that in the absence of cooling the temperature of the bearing outer race rises while cooling dramatically lowers the temperature. Also, the coefficient of friction increases with increasing speed. As such, in situ cooling that leads to reduced operational temperature minimizes lubricant degradation that can result from uncontrolled frictional heating.