Shinichiro Hirabayashi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shinichiro Hirabayashi has a total of 120 co-authors. Here are the top co-authors by number of shared publications:
- Toru Sato
Department of Ocean Technology, Policy, and Environment, University of Tokyo, Kashiwa, Japan
23 shared publications - Rodolfo Trentin Gonc¸alves
The University of Tokyo
13 shared publications - Hideyuki Suzuki
OSPL—Ocean Space Planning Laboratory, Department of Systems Innovation, The University of Tokyo, Tokyo 113-8656, Japan
10 shared publications Hideyuki Suzuki
Dept. of Systems innovation, The University of Tokyo, Bunkyo-ku, Tokyo, Japan
8 shared publicationsShigeru Tabeta
4 shared publications- Se-Min Jeong
Department of Naval Architecture and Ocean Engineering, Chosun University, Gwangju 61452, Republic of Korea
3 shared publications
Latest Publications
- Open Access
- 16 November 2026
- Published by Springer Nature in Journal of Marine Science and Technology
A study on aircushion-type platform behavior in regular waves in relation with inner free-surface profiles
This paper presents an experimental and numerical study of simplified aircushion-type platform models, mainly focusing on the internal free surface created by the entrapped air in the chamber. Since the elevation of this free surface significantly affects the motion of the floating platform, investigating its characteristics is of great importance. In this study, to measure and analyze the inner free-surface elevation, both mono- and partitioned-aircushion-type models were tested in regular waves. A conventional box-type floater without an air chamber was also tested under the same wave conditions for comparison. The inner free-surface elevation along the inner air chamber was measured under both fixed and moored conditions. The coupling effects between the inner free-surface elevation and the motion response of the platform are discussed. The inner free-surface profile was numerically reproduced using WAMIT, and the results were compared with experimental data. Results show that in the short-wavelength condition, the inner wave fields exhibit standing waves for both fixed and moored conditions. As the incident wavelength increases, the inner wave fields change into progressive waves for the moored condition, while sloshing patterns are observed for the fixed condition.
- 16 November 2026
- Published by Springer Nature in Journal of Marine Science and Technology
Open AccessA study on aircushion-type platform behavior in regular waves in relation with inner free-surface profiles
This paper presents an experimental and numerical study of simplified aircushion-type platform models, mainly focusing on the internal free surface created by the entrapped air in the chamber. Since the elevation of this free surface significantly affects the motion of the floating platform, investigating its characteristics is of great importance. In this study, to measure and analyze the inner free-surface elevation, both mono- and partitioned-aircushion-type models were tested in regular waves. A conventional box-type floater without an air chamber was also tested under the same wave conditions for comparison. The inner free-surface elevation along the inner air chamber was measured under both fixed and moored conditions. The coupling effects between the inner free-surface elevation and the motion response of the platform are discussed. The inner free-surface profile was numerically reproduced using WAMIT, and the results were compared with experimental data. Results show that in the short-wavelength condition, the inner wave fields exhibit standing waves for both fixed and moored conditions. As the incident wavelength increases, the inner wave fields change into progressive waves for the moored condition, while sloshing patterns are observed for the fixed condition.
- 6 April 2026
- Published by Elsevier in Ocean Engineering
- Vol. 357
OC7 phase I: CFD investigation of viscous forces on rectangular members of semisubmersibles
- 6 April 2026
- Published by Elsevier in Ocean Engineering
- Vol. 357
OC7 phase I: CFD investigation of viscous forces on rectangular members of semisubmersibles
- 17 November 2025
- Published by Wiley in Journal of Field Robotics
- Vol. 42 (8)
Cover Image, Volume 42, Number 8, December 2025
- 17 November 2025
- Published by Wiley in Journal of Field Robotics
- Vol. 42 (8)
Cover Image, Volume 42, Number 8, December 2025
- Open Access
- 30 September 2025
- Published by Wiley in Journal of Field Robotics
- Vol. 42 (8) , 4589-4608
Tracking Mooring Lines of Floating Structures by an Autonomous Underwater Vehicle
This study presents a novel method for tracking mooring lines of Floating Offshore Wind Turbines (FOWTs) using an Autonomous Underwater Vehicle (AUV) equipped with a tilt‐controlled Multibeam Imaging Sonar (MBS). The proposed approach enables the AUV to estimate the 3D positions of mooring lines and safely track them in real‐time, overcoming the limitations of traditional Remotely Operated Vehicle (ROV)‐based inspections. By utilizing the tilt‐controlled MBS and a pre‐trained You Only Look Once (YOLO) model, the AUV identifies the mooring lines within sonar imagery and dynamically adjusts its velocities to maintain a safe distance during the inspection. A re‐navigation method using the Rauch‐Tung‐Striebel (RTS) smoother enhances the AUV's localization accuracy by correcting its trajectory using post‐processed data from sensors such as the Doppler Velocity Log (DVL), Super Short Baseline (SSBL) system, and Global Navigation Satellite System (GNSS). Additionally, reconstruction with catenary curve fitting is employed to estimate the mooring line's catenary parameters, offering insights into its potential deformation. The approach was validated using a hovering‐type AUV, Tri‐TON through both tank experiments and a sea experiment at an FOWT Hibiki in Kitakyushu, Japan. In the sea experiment, the AUV successfully tracked the mooring lines for 423 s, demonstrating its ability to estimate the position and catenary parameters of the mooring lines. The experimental results highlight areas for future improvement, particularly in enhancing localization accuracy, developing robust control algorithms, and expanding the analysis of mooring line conditions. This method lays the groundwork for future advancements in automated mooring line inspections and enables the integration of additional techniques, such as visual inspection.
- 30 September 2025
- Published by Wiley in Journal of Field Robotics
- Vol. 42 (8) , 4589-4608
Open AccessTracking Mooring Lines of Floating Structures by an Autonomous Underwater Vehicle
This study presents a novel method for tracking mooring lines of Floating Offshore Wind Turbines (FOWTs) using an Autonomous Underwater Vehicle (AUV) equipped with a tilt‐controlled Multibeam Imaging Sonar (MBS). The proposed approach enables the AUV to estimate the 3D positions of mooring lines and safely track them in real‐time, overcoming the limitations of traditional Remotely Operated Vehicle (ROV)‐based inspections. By utilizing the tilt‐controlled MBS and a pre‐trained You Only Look Once (YOLO) model, the AUV identifies the mooring lines within sonar imagery and dynamically adjusts its velocities to maintain a safe distance during the inspection. A re‐navigation method using the Rauch‐Tung‐Striebel (RTS) smoother enhances the AUV's localization accuracy by correcting its trajectory using post‐processed data from sensors such as the Doppler Velocity Log (DVL), Super Short Baseline (SSBL) system, and Global Navigation Satellite System (GNSS). Additionally, reconstruction with catenary curve fitting is employed to estimate the mooring line's catenary parameters, offering insights into its potential deformation. The approach was validated using a hovering‐type AUV, Tri‐TON through both tank experiments and a sea experiment at an FOWT Hibiki in Kitakyushu, Japan. In the sea experiment, the AUV successfully tracked the mooring lines for 423 s, demonstrating its ability to estimate the position and catenary parameters of the mooring lines. The experimental results highlight areas for future improvement, particularly in enhancing localization accuracy, developing robust control algorithms, and expanding the analysis of mooring line conditions. This method lays the groundwork for future advancements in automated mooring line inspections and enables the integration of additional techniques, such as visual inspection.
- 26 December 2022
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 145 (3) , 1-9
Influence of Heave Plate on the Flow-Induced Motions of a Floating Offshore Wind Turbine
Flow-induce motions (FIM) small-scale model tests were performed for the Jappaku floating offshore wind turbines (JPK), a FOWT developed to operate in Brazilian waters. This paper aims to investigate the presence of FIM on the JPK to show the importance of heave plate (HP) design and to show how HP mitigates FIM. Three different HP dimensions were tested and compared with the condition without HP. In addition, two different incidence angles of the current were tested, namely, 0 deg and 180 deg. The results showed amplitudes in the transverse direction similar to the diameter of the external platform column for the case without HP. These amplitudes are higher than the ones observed for previous deep-draft semi-submersibles found in the literature. Conversely, the largest HP dimensions implied in mitigation of the FIM amplitudes, i.e., very low amplitudes, were observed. The presence of the central column played an essential role in FIM and significantly modified the amplitudes in different current incidences. Due to the different diameters of the external and central columns, the FIM presented two different branches of response related to the vortex-shedding frequency around the columns. The results showed that significant FIM could occur for this specific JPK investigation even with HP. The HP design has a positive effect on reducing dynamic behaviors due to the wave and current incidences. Therefore, its design must be included in the preliminary stages of FOWT developments.
- 26 December 2022
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 145 (3) , 1-9
Influence of Heave Plate on the Flow-Induced Motions of a Floating Offshore Wind Turbine
Flow-induce motions (FIM) small-scale model tests were performed for the Jappaku floating offshore wind turbines (JPK), a FOWT developed to operate in Brazilian waters. This paper aims to investigate the presence of FIM on the JPK to show the importance of heave plate (HP) design and to show how HP mitigates FIM. Three different HP dimensions were tested and compared with the condition without HP. In addition, two different incidence angles of the current were tested, namely, 0 deg and 180 deg. The results showed amplitudes in the transverse direction similar to the diameter of the external platform column for the case without HP. These amplitudes are higher than the ones observed for previous deep-draft semi-submersibles found in the literature. Conversely, the largest HP dimensions implied in mitigation of the FIM amplitudes, i.e., very low amplitudes, were observed. The presence of the central column played an essential role in FIM and significantly modified the amplitudes in different current incidences. Due to the different diameters of the external and central columns, the FIM presented two different branches of response related to the vortex-shedding frequency around the columns. The results showed that significant FIM could occur for this specific JPK investigation even with HP. The HP design has a positive effect on reducing dynamic behaviors due to the wave and current incidences. Therefore, its design must be included in the preliminary stages of FOWT developments.
- Open Access
- 16 July 2021
- Published by ASME International
Numerical and Experimental Comparison of the Wave Response of a Very Light Floating Offshore Wind Turbine With Guy Wires
A floating offshore wind turbine (FOWT) concept with a guy wire supported tower was investigated to obtain results on its elastic response characteristics in waves. The concept aim is to reduce the cost of FOWTs by using a light-weight structure tensioned with guy wires and a downwind turbine concept. Thereby, the whole floater is a weathervane system, adjusting itself into
- 16 July 2021
- Published by ASME International
Open AccessNumerical and Experimental Comparison of the Wave Response of a Very Light Floating Offshore Wind Turbine With Guy Wires
A floating offshore wind turbine (FOWT) concept with a guy wire supported tower was investigated to obtain results on its elastic response characteristics in waves. The concept aim is to reduce the cost of FOWTs by using a light-weight structure tensioned with guy wires and a downwind turbine concept. Thereby, the whole floater is a weathervane system, adjusting itself into
- Open Access
- 16 July 2021
- Published by ASME International
Column Interference Effect of Multi-Column Floating Structures on Vortex-Induced Motion
Floating Offshore Wind Turbine (FOWT) shows complex motion behavior because of the wind load for turbine and wave and current loads for floater. Recently, viscous effect of hydrodynamic phenomenon is getting more attention for the improvement of the motion prediction. Vortex-Induced Motion (VIM) of a floating structure is one of those phenomena, which is driven by the pressure
- 16 July 2021
- Published by ASME International
Open AccessColumn Interference Effect of Multi-Column Floating Structures on Vortex-Induced Motion
Floating Offshore Wind Turbine (FOWT) shows complex motion behavior because of the wind load for turbine and wave and current loads for floater. Recently, viscous effect of hydrodynamic phenomenon is getting more attention for the improvement of the motion prediction. Vortex-Induced Motion (VIM) of a floating structure is one of those phenomena, which is driven by the pressure
- Open Access
- 16 July 2021
- Published by ASME International
Experimental Study of the Effect of the Pontoon Dimensions on the Flow-Induced Motions (Fim) of a Semi-Submersible Platform With Four Square Columns
The Flow-Induced Motions (FIM) is an essential topic on multi-column platforms due to the effect on the mooring line fatigue life. Vortex-Induced Motions (VIM) or galloping behavior can be observed for an array of four columns with square sections. The presence of pontoons showed to be important for changing the flow around the array and promote different amplitude behavior of the
- 16 July 2021
- Published by ASME International
Open AccessExperimental Study of the Effect of the Pontoon Dimensions on the Flow-Induced Motions (Fim) of a Semi-Submersible Platform With Four Square Columns
The Flow-Induced Motions (FIM) is an essential topic on multi-column platforms due to the effect on the mooring line fatigue life. Vortex-Induced Motions (VIM) or galloping behavior can be observed for an array of four columns with square sections. The presence of pontoons showed to be important for changing the flow around the array and promote different amplitude behavior of the
- 5 March 2021
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 26 (4) , 1153-1169
2D CFD on flow-induced forces of three circular, square and diamond columns in equilateral arrangements at low Reynolds number
- 5 March 2021
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 26 (4) , 1153-1169
2D CFD on flow-induced forces of three circular, square and diamond columns in equilateral arrangements at low Reynolds number
- Open Access
- 26 October 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (11) , 841
Wave and Wind Responses of a Very-Light FOWT with Guy-Wired-Supported Tower: Numerical and Experimental Studies
A floating offshore wind turbine (FOWT) concept with a guy-wire-supported tower was investigated to obtain motion results in waves considering its elastic model characteristics. The FOWT concept studied aims to reduce the construction costs by using a light-weight structure tensioned with guy wires and a downwind type. Wave tank experiments of an elastically similar segmented backbone model in the 1:60 scale were carried out to clarify the dynamic elastic response features of the structure. The experimental results were compared with numerical simulations obtained from NK-UTWind and WAMIT codes. The bending moment measured at the tower and pontoons had two peak values for different wave periods carried out. The short-wave period peak was due to sagging/hogging when the wavelength matched the floater length. The second peak was due to the large tower top acceleration, which caused a large bending moment at the tower base and pontoon to support the inertia force. The wind force was not significant to modify the FOWT response. The sensibility analysis in pontoons and tower rigidities confirmed the importance of the guy wires to support the inertia due to the waves and wind incidence. The new concept of a very-light FOWT with a guy-wire-supported tower may be an option for future FOWT developments.
- 26 October 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (11) , 841
Open AccessWave and Wind Responses of a Very-Light FOWT with Guy-Wired-Supported Tower: Numerical and Experimental Studies
A floating offshore wind turbine (FOWT) concept with a guy-wire-supported tower was investigated to obtain motion results in waves considering its elastic model characteristics. The FOWT concept studied aims to reduce the construction costs by using a light-weight structure tensioned with guy wires and a downwind type. Wave tank experiments of an elastically similar segmented backbone model in the 1:60 scale were carried out to clarify the dynamic elastic response features of the structure. The experimental results were compared with numerical simulations obtained from NK-UTWind and WAMIT codes. The bending moment measured at the tower and pontoons had two peak values for different wave periods carried out. The short-wave period peak was due to sagging/hogging when the wavelength matched the floater length. The second peak was due to the large tower top acceleration, which caused a large bending moment at the tower base and pontoon to support the inertia force. The wind force was not significant to modify the FOWT response. The sensibility analysis in pontoons and tower rigidities confirmed the importance of the guy wires to support the inertia due to the waves and wind incidence. The new concept of a very-light FOWT with a guy-wire-supported tower may be an option for future FOWT developments.