Shahid Rauf
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shahid Rauf has a total of 152 co-authors. Here are the top co-authors by number of shared publications:
- Kallol Bera
Applied Materials, Inc., 3333 Scott Blvd., Santa Clara, CA 95054, United States of America
10 shared publications - Jason Kenney
Applied Materials, Inc. 1 , 3333 Scott Blvd., Santa Clara, California 95054
9 shared publications - Igor. D. Kaganovich
Princeton Plasma Physics Laboratory
6 shared publications - Ihor Korolov
Ruhr University Bochum
6 shared publications - Julian Schulze
Ruhr University Bochum
6 shared publications Jason Kenney
Applied Materials Inc., Santa Clara, California, United States
5 shared publications
Latest Publications
- 1 September 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (5)
Inductively coupled plasma driven by asymmetric triangular current waveform
Two-dimensional particle-in-cell simulations of an inductively coupled plasma (ICP) are used to investigate the influence of radio-frequency (RF) current waveform and frequency on plasma characteristics, collision processes, and the electron velocity distribution function (EVDF). Plasmas driven by sinusoidal coil current over the frequency range of 1–30 MHz and by asymmetric triangular waveform current at 1 MHz are examined at 25 mTorr. For sinusoidal excitation, significantly lower coil current is required at higher frequencies to achieve comparable electron density, consistent with the scaling of inductive electric fields with frequency. Plasma production shifts toward the plasma—dielectric interface with increasing frequency due to reduced skin depth. Despite differences in power deposition localization, strong ambipolar diffusion in the small chamber results in broadly similar plasma density profiles across frequencies. For asymmetric triangular waveform current, the inductive electric field is strongly enhanced during the faster current ramp-down phase, leading to pronounced temporal modulation of electron heating. Increasing waveform duty cycle (DC) enhances the contribution of higher current harmonics, which results in higher steady-state electron density. Excitation and ionization processes also shift closer to the plasma—dielectric interface. The EVDF becomes increasingly asymmetric with increasing DC, reflecting preferential electron acceleration during the current ramp-down phase. Time-resolved analysis shows that excitation and ionization rates peak sharply during this phase, with ionization exhibiting stronger relative enhancement. The intense plasma current produced during the current ramp-down phase persists beyond the reversal of the source electric field due to electron inertia and collisional effects. Consequently, inductive electron power deposition continues in the plasma for several tens of nanoseconds after the coil current reverses direction. These results demonstrate that RF current waveform asymmetry provides a viable mechanism for controlling electron power deposition, EVDF, and electron-impact collisional processes in ICPs.
- 1 September 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (5)
Inductively coupled plasma driven by asymmetric triangular current waveform
Two-dimensional particle-in-cell simulations of an inductively coupled plasma (ICP) are used to investigate the influence of radio-frequency (RF) current waveform and frequency on plasma characteristics, collision processes, and the electron velocity distribution function (EVDF). Plasmas driven by sinusoidal coil current over the frequency range of 1–30 MHz and by asymmetric triangular waveform current at 1 MHz are examined at 25 mTorr. For sinusoidal excitation, significantly lower coil current is required at higher frequencies to achieve comparable electron density, consistent with the scaling of inductive electric fields with frequency. Plasma production shifts toward the plasma—dielectric interface with increasing frequency due to reduced skin depth. Despite differences in power deposition localization, strong ambipolar diffusion in the small chamber results in broadly similar plasma density profiles across frequencies. For asymmetric triangular waveform current, the inductive electric field is strongly enhanced during the faster current ramp-down phase, leading to pronounced temporal modulation of electron heating. Increasing waveform duty cycle (DC) enhances the contribution of higher current harmonics, which results in higher steady-state electron density. Excitation and ionization processes also shift closer to the plasma—dielectric interface. The EVDF becomes increasingly asymmetric with increasing DC, reflecting preferential electron acceleration during the current ramp-down phase. Time-resolved analysis shows that excitation and ionization rates peak sharply during this phase, with ionization exhibiting stronger relative enhancement. The intense plasma current produced during the current ramp-down phase persists beyond the reversal of the source electric field due to electron inertia and collisional effects. Consequently, inductive electron power deposition continues in the plasma for several tens of nanoseconds after the coil current reverses direction. These results demonstrate that RF current waveform asymmetry provides a viable mechanism for controlling electron power deposition, EVDF, and electron-impact collisional processes in ICPs.
- 31 March 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (4)
N 2 capacitively coupled plasma - Moment analysis of particle-in-cell modeling results
A one-dimensional (1D) particle-in-cell/Monte Carlo collision (PIC/MCC) simulation study of nitrogen (N₂) capacitively coupled plasma (CCP) is presented for a pressure range between 0.1 and 1.5 Torr (13.33 – 199.98 Pa). The primary objective is to use moment analysis of charged particle data to systematically examine the validity of commonly employed assumptions in fluid plasma models for intermediate pressure CCPs. The voltage and pressure range investigated include the CCP operating in the α and γ modes as well as conditions with significant electron power absorption in the bulk plasma. At RF voltage V RF = 200 V (amplitude) and ion-induced secondary electron emission coefficient γ = 0.2, the bulk plasma region broadens with increasing pressure as a result of reduced electron and ion mean free paths. Electron power absorption increases in the bulk plasma at 0.5 Torr (66.66 Pa) and higher pressures, but it does not contribute significantly to plasma production. The plasma transitions from the α to γ mode as V RF is increased from 200 to 350 V at 0.1 Torr (13.33 Pa) with significant lowering of T e and increase of electron density (n e ) in the bulk plasma. The collision frequencies for individual electron impact reactions as well as the total collision frequency do not exhibit a straight-forward one-on-one relationship to electron temperature (T e ) or total electron energy (ε e ). This finding contrasts with the common assumption in fluid models for CCPs. Moment analysis of the momentum conservation equations reveals that the drift-diffusion approximation is valid for electrons in the bulk plasma and the pre-sheath region under both α- and γ-mode conditions. While ion momentum transport is dominated by sheath acceleration and collisional damping, the inertia term in the ion momentum equation is important at all pressures considered.
- 31 March 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (4)
N 2 capacitively coupled plasma - Moment analysis of particle-in-cell modeling results
A one-dimensional (1D) particle-in-cell/Monte Carlo collision (PIC/MCC) simulation study of nitrogen (N₂) capacitively coupled plasma (CCP) is presented for a pressure range between 0.1 and 1.5 Torr (13.33 – 199.98 Pa). The primary objective is to use moment analysis of charged particle data to systematically examine the validity of commonly employed assumptions in fluid plasma models for intermediate pressure CCPs. The voltage and pressure range investigated include the CCP operating in the α and γ modes as well as conditions with significant electron power absorption in the bulk plasma. At RF voltage V RF = 200 V (amplitude) and ion-induced secondary electron emission coefficient γ = 0.2, the bulk plasma region broadens with increasing pressure as a result of reduced electron and ion mean free paths. Electron power absorption increases in the bulk plasma at 0.5 Torr (66.66 Pa) and higher pressures, but it does not contribute significantly to plasma production. The plasma transitions from the α to γ mode as V RF is increased from 200 to 350 V at 0.1 Torr (13.33 Pa) with significant lowering of T e and increase of electron density (n e ) in the bulk plasma. The collision frequencies for individual electron impact reactions as well as the total collision frequency do not exhibit a straight-forward one-on-one relationship to electron temperature (T e ) or total electron energy (ε e ). This finding contrasts with the common assumption in fluid models for CCPs. Moment analysis of the momentum conservation equations reveals that the drift-diffusion approximation is valid for electrons in the bulk plasma and the pre-sheath region under both α- and γ-mode conditions. While ion momentum transport is dominated by sheath acceleration and collisional damping, the inertia term in the ion momentum equation is important at all pressures considered.
- Open Access
- 1 February 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (2)
Ion–ion oscillation and periodic emission pattern in electronegative capacitively coupled radio frequency plasmas
Experimental observation and numerical analysis of low-frequency (LF) waveform-induced ion–plasma oscillations in low-pressure capacitively coupled plasmas operated in argon/oxygen mixtures are reported. We investigate the spatiotemporal excitation dynamics of dual-frequency (high-frequency, HF = 13.56 MHz and low-frequency, LF = 135–400 kHz) voltage-driven discharges using phase-resolved optical emission spectroscopy. Under oxygen-rich and low-pressure conditions (<10 Pa), distinct megahertz-range oscillations emerge in the excitation rates, indicating the onset of ion–ion plasma wave phenomena. These oscillations are predominantly triggered by the sharp transitions of external LF waveforms and persist throughout the LF cycle. One-dimensional particle-in-cell/Monte Carlo simulations reproduce the observed oscillation patterns and confirm their origin as electrostatic waves driven by LF-induced charge separation between positive and negative ions. The oscillation frequency is found to depend on ion density and gas composition, providing sheath modulation at a time scale intermediate between the HF and LF components. These waves offer new insight into plasma heating mechanisms in dual-frequency discharges and serve as a sensitive diagnostic of plasma conditions.
- 1 February 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (2)
Open AccessIon–ion oscillation and periodic emission pattern in electronegative capacitively coupled radio frequency plasmas
Experimental observation and numerical analysis of low-frequency (LF) waveform-induced ion–plasma oscillations in low-pressure capacitively coupled plasmas operated in argon/oxygen mixtures are reported. We investigate the spatiotemporal excitation dynamics of dual-frequency (high-frequency, HF = 13.56 MHz and low-frequency, LF = 135–400 kHz) voltage-driven discharges using phase-resolved optical emission spectroscopy. Under oxygen-rich and low-pressure conditions (<10 Pa), distinct megahertz-range oscillations emerge in the excitation rates, indicating the onset of ion–ion plasma wave phenomena. These oscillations are predominantly triggered by the sharp transitions of external LF waveforms and persist throughout the LF cycle. One-dimensional particle-in-cell/Monte Carlo simulations reproduce the observed oscillation patterns and confirm their origin as electrostatic waves driven by LF-induced charge separation between positive and negative ions. The oscillation frequency is found to depend on ion density and gas composition, providing sheath modulation at a time scale intermediate between the HF and LF components. These waves offer new insight into plasma heating mechanisms in dual-frequency discharges and serve as a sensitive diagnostic of plasma conditions.
- 10 July 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (5)
Effect of mask geometry on high aspect ratio silicon etching using Cl2/O2 plasma
The relentless growth in computational demands has driven substantial advancements in microelectronic device architectures in recent years. Three-dimensional (3D) structures are now predominant in leading edge logic and memory integrated circuits. These developments pose significant challenges in etching and deposition processes due to the complexity of the 3D geometries. This study focuses on Si etching in an inductively coupled Cl2/O2 plasma. A Monte Carlo-based 3D feature-scale model is used to investigate how the initial mask geometry and operating conditions affect 3D etching profiles. The etching behavior associated with a rectangular mask opening is first examined, highlighting the trade-offs inherent during process development. The impact of initial mask shape on etching outcomes is also explored by comparing the etched profiles across masks with rectangular, square, and circular openings. Despite identical opening areas, these geometries exhibit significant variations in etch characteristics. Through the cases presented, we underscore the process challenges posed by etching 3D features with high aspect ratios, in both the vertical and lateral directions.
- 10 July 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (5)
Effect of mask geometry on high aspect ratio silicon etching using Cl2/O2 plasma
The relentless growth in computational demands has driven substantial advancements in microelectronic device architectures in recent years. Three-dimensional (3D) structures are now predominant in leading edge logic and memory integrated circuits. These developments pose significant challenges in etching and deposition processes due to the complexity of the 3D geometries. This study focuses on Si etching in an inductively coupled Cl2/O2 plasma. A Monte Carlo-based 3D feature-scale model is used to investigate how the initial mask geometry and operating conditions affect 3D etching profiles. The etching behavior associated with a rectangular mask opening is first examined, highlighting the trade-offs inherent during process development. The impact of initial mask shape on etching outcomes is also explored by comparing the etched profiles across masks with rectangular, square, and circular openings. Despite identical opening areas, these geometries exhibit significant variations in etch characteristics. Through the cases presented, we underscore the process challenges posed by etching 3D features with high aspect ratios, in both the vertical and lateral directions.
- 2 December 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (1)
On the use of pulsed DC bias for etching high aspect ratio features
Inductively coupled plasmas (ICPs) containing Cl2 are widely used for plasma etching in the semiconductor industry. One common issue during plasma etching is aspect ratio dependent etching (ARDE), which is generally attributed to variation in the flux of etchant species to the bottom of features with different dimensions. Insufficient fluxes of neutral etchants to the bottom of high aspect ratio features can also result in sputtering, which tends to distort the feature profile. This article addresses two issues relevant to Cl2 ICP and plasma etching in these plasmas. First, a comprehensive set of diagnostics is used to validate a model for Cl2 ICP for gas pressure between 3 and 90 mTorr. The plasma diagnostics include microwave resonant hairpin probe-based measurements of electron density, photolysis-calibrated two-photon laser induced fluorescence measurement of Cl density, photo-detachment-based measurement of Cl− density, and laser diode absorption spectroscopy of argon metastable species to measure the gas temperature. Consistent with the experiments, the model shows that the electron density peaks near the center of the chamber at low gas pressure due to rapid diffusion. The electron density peak moves under the coils at higher pressures. Using the validated Cl2 model, we investigate ICPs with rectangular pulsed DC voltage for bias. It is shown that the Cl flux at the bottom of a trench decreases significantly with increasing aspect ratio of the trench. Neutral to ion flux ratio is therefore low at the bottom of higher aspect ratio trenches. The duty cycle of the pulsed bias waveform is found to be an effective means of increasing the neutral to energetic ion flux ratio, which should help with ARDE and sputter reduction.
- 2 December 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (1)
On the use of pulsed DC bias for etching high aspect ratio features
Inductively coupled plasmas (ICPs) containing Cl2 are widely used for plasma etching in the semiconductor industry. One common issue during plasma etching is aspect ratio dependent etching (ARDE), which is generally attributed to variation in the flux of etchant species to the bottom of features with different dimensions. Insufficient fluxes of neutral etchants to the bottom of high aspect ratio features can also result in sputtering, which tends to distort the feature profile. This article addresses two issues relevant to Cl2 ICP and plasma etching in these plasmas. First, a comprehensive set of diagnostics is used to validate a model for Cl2 ICP for gas pressure between 3 and 90 mTorr. The plasma diagnostics include microwave resonant hairpin probe-based measurements of electron density, photolysis-calibrated two-photon laser induced fluorescence measurement of Cl density, photo-detachment-based measurement of Cl− density, and laser diode absorption spectroscopy of argon metastable species to measure the gas temperature. Consistent with the experiments, the model shows that the electron density peaks near the center of the chamber at low gas pressure due to rapid diffusion. The electron density peak moves under the coils at higher pressures. Using the validated Cl2 model, we investigate ICPs with rectangular pulsed DC voltage for bias. It is shown that the Cl flux at the bottom of a trench decreases significantly with increasing aspect ratio of the trench. Neutral to ion flux ratio is therefore low at the bottom of higher aspect ratio trenches. The duty cycle of the pulsed bias waveform is found to be an effective means of increasing the neutral to energetic ion flux ratio, which should help with ARDE and sputter reduction.
- 1 December 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (12) , 125001
Ar/CF4 capacitively coupled plasma generated using 40 MHz sinusoidal and 800 kHz rectangular waveform voltages
This article discusses the characteristics of an Ar/CF4 capacitively coupled plasma (CCP) excited using 40 MHz sinusoidal and 800 kHz rectangular voltage waveforms. The simulations focus on the effect of the low frequency (LF) rectangular wave duty cycle (defined as the period at negative voltage) on the plasma properties and uniformity for constant 100 W power at 40 MHz and 20 mTorr gas pressure. Given the importance of kinetic effects in low pressure CCPs, a hybrid plasma model is used. This model treats electrons as particles using the particle-in-cell formalism while ions and neutral species are represented as fluids. By incorporating electron kinetic effects, this approach allows for the accurate modeling of low-pressure CCPs with complex plasma chemistries. Results show that, at 80% duty cycle, the peak in the density of all species is near the edge of the electrodes. As the LF rectangular wave duty cycle is decreased while keeping the 40 MHz power fixed, the species’ densities increase, the 40 MHz radio-frequency voltage decreases, and the peak in species’ densities shifts towards the chamber center. These trends can be explained based on how the LF voltage modulates the coupling of 40 MHz power to the electrons. Under the conditions considered, the plasma is mostly produced through electron stochastic heating at the sheath edge by the 40 MHz voltage. The 40 MHz couples to the electrons more efficiently when the LF voltage at the powered electrode sheath is small and the sheath is thin. The plasma is produced relatively uniformly in the inter-electrode region during this phase. Therefore, at small duty cycles when the powered electrode sheath is thin for a long time, the plasma is uniform and requires a smaller 40 MHz voltage to deposit 100 W at 40 MHz in the plasma. When the LF voltage in the powered electrode sheath is large and negative, plasma production is weak and occurs at the edge of the powered electrode where the sheath is thinner. At large duty cycles, the plasma is efficiently produced for only a short period, necessitating a larger 40 MHz voltage. The plasma density also peaks near the electrode edge at large duty cycles.
- 1 December 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (12) , 125001
Ar/CF4 capacitively coupled plasma generated using 40 MHz sinusoidal and 800 kHz rectangular waveform voltages
This article discusses the characteristics of an Ar/CF4 capacitively coupled plasma (CCP) excited using 40 MHz sinusoidal and 800 kHz rectangular voltage waveforms. The simulations focus on the effect of the low frequency (LF) rectangular wave duty cycle (defined as the period at negative voltage) on the plasma properties and uniformity for constant 100 W power at 40 MHz and 20 mTorr gas pressure. Given the importance of kinetic effects in low pressure CCPs, a hybrid plasma model is used. This model treats electrons as particles using the particle-in-cell formalism while ions and neutral species are represented as fluids. By incorporating electron kinetic effects, this approach allows for the accurate modeling of low-pressure CCPs with complex plasma chemistries. Results show that, at 80% duty cycle, the peak in the density of all species is near the edge of the electrodes. As the LF rectangular wave duty cycle is decreased while keeping the 40 MHz power fixed, the species’ densities increase, the 40 MHz radio-frequency voltage decreases, and the peak in species’ densities shifts towards the chamber center. These trends can be explained based on how the LF voltage modulates the coupling of 40 MHz power to the electrons. Under the conditions considered, the plasma is mostly produced through electron stochastic heating at the sheath edge by the 40 MHz voltage. The 40 MHz couples to the electrons more efficiently when the LF voltage at the powered electrode sheath is small and the sheath is thin. The plasma is produced relatively uniformly in the inter-electrode region during this phase. Therefore, at small duty cycles when the powered electrode sheath is thin for a long time, the plasma is uniform and requires a smaller 40 MHz voltage to deposit 100 W at 40 MHz in the plasma. When the LF voltage in the powered electrode sheath is large and negative, plasma production is weak and occurs at the edge of the powered electrode where the sheath is thinner. At large duty cycles, the plasma is efficiently produced for only a short period, necessitating a larger 40 MHz voltage. The plasma density also peaks near the electrode edge at large duty cycles.
- Open Access
- 1 October 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (10)
Investigating instabilities in magnetized low-pressure capacitively coupled RF plasma using particle-in-cell (PIC) simulations
The effect of a uniform magnetic field on particle transport in low-pressure radio frequency (RF) capacitively coupled plasma (CCP) has been studied using a particle-in-cell model. Three distinct regimes of plasma behavior can be identified as a function of the magnetic field. In the first regime at low magnetic fields, asymmetric plasma profiles are observed within the CCP chamber due to the effect of E→×B→ drift. As the magnetic field increases, instabilities develop and form self-organized spoke-shaped structures that are distinctly seen within the bulk plasma closer to the sheath. In this second regime, the spoke-shaped coherent structures rotate inside the plasma chamber in the −E→×B→ direction, where E→ and B→ are the DC electric and magnetic field vectors, respectively, and the DC electric field exists in the sheath and pre-sheath regions. The spoke rotation frequency is in the megahertz range. As the magnetic field strength increases further, the rotating coherent spokes continue to exist near the sheath. The coherent structures are, however, accompanied by new small-scale incoherent structures originating and moving within the bulk plasma region away from the sheath. This is the third regime of plasma behavior. The threshold values of the magnetic field between these regimes were found not to vary with changing plasma reactor geometry (e.g., area ratio between ground and powered electrodes) or the use of an external capacitor between the RF-powered electrode and the RF source. The threshold values of the magnetic field between these regimes shift toward higher values with increasing gas pressure. Analysis of the results indicates that the rotating structures are due to the lower hybrid instability driven by density gradients and electron-neutral collisions. This paper provides guidance on the upper limit of the magnetic field for instability-free operation in low-pressure CCP-based semiconductor deposition and etch systems that use the external magnetic field for plasma uniformity control.
- 1 October 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (10)
Open AccessInvestigating instabilities in magnetized low-pressure capacitively coupled RF plasma using particle-in-cell (PIC) simulations
The effect of a uniform magnetic field on particle transport in low-pressure radio frequency (RF) capacitively coupled plasma (CCP) has been studied using a particle-in-cell model. Three distinct regimes of plasma behavior can be identified as a function of the magnetic field. In the first regime at low magnetic fields, asymmetric plasma profiles are observed within the CCP chamber due to the effect of E→×B→ drift. As the magnetic field increases, instabilities develop and form self-organized spoke-shaped structures that are distinctly seen within the bulk plasma closer to the sheath. In this second regime, the spoke-shaped coherent structures rotate inside the plasma chamber in the −E→×B→ direction, where E→ and B→ are the DC electric and magnetic field vectors, respectively, and the DC electric field exists in the sheath and pre-sheath regions. The spoke rotation frequency is in the megahertz range. As the magnetic field strength increases further, the rotating coherent spokes continue to exist near the sheath. The coherent structures are, however, accompanied by new small-scale incoherent structures originating and moving within the bulk plasma region away from the sheath. This is the third regime of plasma behavior. The threshold values of the magnetic field between these regimes were found not to vary with changing plasma reactor geometry (e.g., area ratio between ground and powered electrodes) or the use of an external capacitor between the RF-powered electrode and the RF source. The threshold values of the magnetic field between these regimes shift toward higher values with increasing gas pressure. Analysis of the results indicates that the rotating structures are due to the lower hybrid instability driven by density gradients and electron-neutral collisions. This paper provides guidance on the upper limit of the magnetic field for instability-free operation in low-pressure CCP-based semiconductor deposition and etch systems that use the external magnetic field for plasma uniformity control.
- Top Cited PapersOpen Access
- 7 June 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 42 (4)
Future of plasma etching for microelectronics: Challenges and opportunities
Plasma etching is an essential semiconductor manufacturing technology required to enable the current microelectronics industry. Along with lithographic patterning, thin-film formation methods, and others, plasma etching has dynamically evolved to meet the exponentially growing demands of the microelectronics industry that enables modern society. At this time, plasma etching faces a period of unprecedented changes owing to numerous factors, including aggressive transition to three-dimensional (3D) device architectures, process precision approaching atomic-scale critical dimensions, introduction of new materials, fundamental silicon device limits, and parallel evolution of post-CMOS approaches. The vast growth of the microelectronics industry has emphasized its role in addressing major societal challenges, including questions on the sustainability of the associated energy use, semiconductor manufacturing related emissions of greenhouse gases, and others. The goal of this article is to help both define the challenges for plasma etching and point out effective plasma etching technology options that may play essential roles in defining microelectronics manufacturing in the future. The challenges are accompanied by significant new opportunities, including integrating experiments with various computational approaches such as machine learning/artificial intelligence and progress in computational approaches, including the realization of digital twins of physical etch chambers through hybrid/coupled models. These prospects can enable innovative solutions to problems that were not available during the past 50 years of plasma etch development in the microelectronics industry. To elaborate on these perspectives, the present article brings together the views of various experts on the different topics that will shape plasma etching for microelectronics manufacturing of the future.
- 7 June 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 42 (4)
Top Cited PapersOpen AccessFuture of plasma etching for microelectronics: Challenges and opportunities
Plasma etching is an essential semiconductor manufacturing technology required to enable the current microelectronics industry. Along with lithographic patterning, thin-film formation methods, and others, plasma etching has dynamically evolved to meet the exponentially growing demands of the microelectronics industry that enables modern society. At this time, plasma etching faces a period of unprecedented changes owing to numerous factors, including aggressive transition to three-dimensional (3D) device architectures, process precision approaching atomic-scale critical dimensions, introduction of new materials, fundamental silicon device limits, and parallel evolution of post-CMOS approaches. The vast growth of the microelectronics industry has emphasized its role in addressing major societal challenges, including questions on the sustainability of the associated energy use, semiconductor manufacturing related emissions of greenhouse gases, and others. The goal of this article is to help both define the challenges for plasma etching and point out effective plasma etching technology options that may play essential roles in defining microelectronics manufacturing in the future. The challenges are accompanied by significant new opportunities, including integrating experiments with various computational approaches such as machine learning/artificial intelligence and progress in computational approaches, including the realization of digital twins of physical etch chambers through hybrid/coupled models. These prospects can enable innovative solutions to problems that were not available during the past 50 years of plasma etch development in the microelectronics industry. To elaborate on these perspectives, the present article brings together the views of various experts on the different topics that will shape plasma etching for microelectronics manufacturing of the future.
- 3 June 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 42 (4)
Science challenges and research opportunities for plasma applications in microelectronics
Low-temperature plasmas (LTPs) are essential to manufacturing devices in the semiconductor industry, from creating extreme ultraviolet photons used in the most advanced lithography to thin film etching, deposition, and surface modifications. It is estimated that 40%–45% of all process steps needed to manufacture semiconductor devices use LTPs in one form or another. LTPs have been an enabling technology in the multidecade progression of the shrinking of device dimensions, often referred to as Moore’s law. New challenges in circuit and device design, novel materials, and increasing demands to achieve environmentally benign processing technologies require advances in plasma technology beyond the current state-of-the-art. The Department of Energy Office of Science Fusion Energy Sciences held a workshop titled Plasma Science for Microelectronics Nanofabrication in August 2022 to discuss the plasma science challenges and technical barriers that need to be overcome to continue to develop the innovative plasma technologies required to support and advance the semiconductor industry. One of the key outcomes of the workshop was identifying a set of priority research opportunities (PROs) to focus attention on the most strategic plasma science challenges to address to benefit the semiconductor industry. For each PRO, scientific challenges and recommended strategies to address those challenges were identified. This article summarizes the PROs identified by the workshop participants.
- 3 June 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 42 (4)
Science challenges and research opportunities for plasma applications in microelectronics
Low-temperature plasmas (LTPs) are essential to manufacturing devices in the semiconductor industry, from creating extreme ultraviolet photons used in the most advanced lithography to thin film etching, deposition, and surface modifications. It is estimated that 40%–45% of all process steps needed to manufacture semiconductor devices use LTPs in one form or another. LTPs have been an enabling technology in the multidecade progression of the shrinking of device dimensions, often referred to as Moore’s law. New challenges in circuit and device design, novel materials, and increasing demands to achieve environmentally benign processing technologies require advances in plasma technology beyond the current state-of-the-art. The Department of Energy Office of Science Fusion Energy Sciences held a workshop titled Plasma Science for Microelectronics Nanofabrication in August 2022 to discuss the plasma science challenges and technical barriers that need to be overcome to continue to develop the innovative plasma technologies required to support and advance the semiconductor industry. One of the key outcomes of the workshop was identifying a set of priority research opportunities (PROs) to focus attention on the most strategic plasma science challenges to address to benefit the semiconductor industry. For each PRO, scientific challenges and recommended strategies to address those challenges were identified. This article summarizes the PROs identified by the workshop participants.
- 14 May 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (4)
Case study in machine learning for predicting moderate pressure plasma behavior
Modeling and forecasting the dynamics of complex systems, such as moderate pressure capacitively coupled plasma (CCP) systems, remains a challenge due to the interactions of physical and chemical processes across multiple scales. Historically, optimization for a given application would be accomplished via a design of experiment (DOE) study across the various external control parameters. Machine learning (ML) techniques show the potential to “forecast” process conditions not tested in a traditional DOE study and thereby allow better optimization and control of a plasma tool. In this article, we have used standard DOE as well as ML predictions to analyze I-V data in a moderate-pressure CCP system. We have demonstrated that supervised regression ML techniques can be a useful tool for extrapolating data even when a plasma system is undergoing a transition in the heating mode, in this case from the alpha to gamma mode. Classification analysis of control parameters is another possible application of ML techniques that can be deployed for system control. Here, we show that given a large set of measured data, the models can identify the gas ratio in the feed gas as well as correctly identify the operating pressure and electrode gap in almost all the cases.
- 14 May 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (4)
Case study in machine learning for predicting moderate pressure plasma behavior
Modeling and forecasting the dynamics of complex systems, such as moderate pressure capacitively coupled plasma (CCP) systems, remains a challenge due to the interactions of physical and chemical processes across multiple scales. Historically, optimization for a given application would be accomplished via a design of experiment (DOE) study across the various external control parameters. Machine learning (ML) techniques show the potential to “forecast” process conditions not tested in a traditional DOE study and thereby allow better optimization and control of a plasma tool. In this article, we have used standard DOE as well as ML predictions to analyze I-V data in a moderate-pressure CCP system. We have demonstrated that supervised regression ML techniques can be a useful tool for extrapolating data even when a plasma system is undergoing a transition in the heating mode, in this case from the alpha to gamma mode. Classification analysis of control parameters is another possible application of ML techniques that can be deployed for system control. Here, we show that given a large set of measured data, the models can identify the gas ratio in the feed gas as well as correctly identify the operating pressure and electrode gap in almost all the cases.