Orhan Orcun Inan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Orhan Orcun Inan has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Selçuk Atalay
Physics Department, Faculty of Science, Inonu University, 44280 Malatya, Turkey
3 shared publications - Sema Erdemoglu
Chemistry Department, Faculty of Science, Inonu University, 44280 Malatya, Turkey
3 shared publications - Veli Serkan Kolat
Physics Department, Faculty of Science, Inonu University, 44280 Malatya, Turkey
3 shared publications - Emine Mete
Chemistry Department, Faculty of Science, Inonu University, 44280 Malatya, Turkey
2 shared publications - Hatice Çağlar Yılmaz
Technology Transfer Office, Malatya Turgut Özal University, 44090 Malatya, Turkey
2 shared publications - Tekin Izgi
Science Faculty, Physics Department, Inonu University, Malatya, Turkey
1 shared publication
Latest Publications
- Open Access
- 13 February 2025
- Published by MDPI AG in Magnetochemistry
- Vol. 11 (2) , 15
Correction: Atalay et al. Fabrication of a Portable Magnetic Microcantilever Using Fe40Ni38Mo4B18 Amorphous Ribbon and Its Application as a Humidity Sensor by Coating with TiO2 Nanotubes. Magnetochemistry 2024, 10, 98
- 13 February 2025
- Published by MDPI AG in Magnetochemistry
- Vol. 11 (2) , 15
Open AccessCorrection: Atalay et al. Fabrication of a Portable Magnetic Microcantilever Using Fe40Ni38Mo4B18 Amorphous Ribbon and Its Application as a Humidity Sensor by Coating with TiO2 Nanotubes. Magnetochemistry 2024, 10, 98
- Open Access
- 5 December 2024
- Published by MDPI AG in Magnetochemistry
- Vol. 10 (12) , 98
Fabrication of a Portable Magnetic Microcantilever Using Fe40Ni38Mo4B18 Amorphous Ribbon and Its Application as a Humidity Sensor by Coating with TiO2 Nanotubes
Microcantilevers (MCs) are highly sensitive sensors capable of detecting mass changes on the surface at the nanogram and even picogram scale. In this study, microcantilevers were fabricated for the first time using the Sodick AP250L Wire electrical discharge machining (EDM) from amorphous 2826MB (Fe40Ni38Mo4B18) ferromagnetic ribbons. This method is advantageous because it allows for the simultaneous production of a large number of microcantilevers, with about 100 MCs being produced in a single manufacturing process. Additionally, a straightforward and cost-effective measurement system was developed to measure the resonance frequency and frequency shift of the MC entirely through magnetic means, a technique not previously reported in the literature. To evaluate the performance of the MC, we employed it as a humidity sensor. For the TiO2-NT-coated MC, a frequency shift of approximately 202 Hz was observed when the humidity level changed from 5% to 95% relative humidity (RH).
- 5 December 2024
- Published by MDPI AG in Magnetochemistry
- Vol. 10 (12) , 98
Open AccessFabrication of a Portable Magnetic Microcantilever Using Fe40Ni38Mo4B18 Amorphous Ribbon and Its Application as a Humidity Sensor by Coating with TiO2 Nanotubes
Microcantilevers (MCs) are highly sensitive sensors capable of detecting mass changes on the surface at the nanogram and even picogram scale. In this study, microcantilevers were fabricated for the first time using the Sodick AP250L Wire electrical discharge machining (EDM) from amorphous 2826MB (Fe40Ni38Mo4B18) ferromagnetic ribbons. This method is advantageous because it allows for the simultaneous production of a large number of microcantilevers, with about 100 MCs being produced in a single manufacturing process. Additionally, a straightforward and cost-effective measurement system was developed to measure the resonance frequency and frequency shift of the MC entirely through magnetic means, a technique not previously reported in the literature. To evaluate the performance of the MC, we employed it as a humidity sensor. For the TiO2-NT-coated MC, a frequency shift of approximately 202 Hz was observed when the humidity level changed from 5% to 95% relative humidity (RH).
- Open Access
Magnetoelastic Humidity Sensors with TiO2 Nanotube Sensing Layers
In this study, TiO2 nanotubes (TiO2-NTs) are coated with a drop-casting method on Fe40Ni38Mo4B18 amorphous ferromagnetic ribbons and the humidity response of the prepared magnetoelastic sensors (MES) is investigated. The synthesis of TiO2-NTs is performed using a hydrothermal process. Sample characterization is carried out using X-ray diffraction and scanning electron microscopy. The results show that the sensors can measure moisture values in the range of 5% to 95% with very high precision and very low hysteresis. The humidity variation between 5% and 95% shows a change in the sensor resonance frequency of ~3180 Hz, which is a significant change compared to many magnetoelastic humidity sensors developed so far.
Open AccessMagnetoelastic Humidity Sensors with TiO2 Nanotube Sensing Layers
In this study, TiO2 nanotubes (TiO2-NTs) are coated with a drop-casting method on Fe40Ni38Mo4B18 amorphous ferromagnetic ribbons and the humidity response of the prepared magnetoelastic sensors (MES) is investigated. The synthesis of TiO2-NTs is performed using a hydrothermal process. Sample characterization is carried out using X-ray diffraction and scanning electron microscopy. The results show that the sensors can measure moisture values in the range of 5% to 95% with very high precision and very low hysteresis. The humidity variation between 5% and 95% shows a change in the sensor resonance frequency of ~3180 Hz, which is a significant change compared to many magnetoelastic humidity sensors developed so far.