Sivasubramanian Mahadevan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sivasubramanian Mahadevan has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Parthasarathy Rajesh Kanna
CO Research and Green Technologies Centre, Vellore Institute of Technology
7 shared publications M. Uthayakumar
5 shared publications- Armstrong Michael
Department of Mechanical Engineering, PSN College of Engineering and Technology, Tirunelveli, Tamil Nadu, India
2 shared publications - Dinesh Kumar Vairavel
School of Mechanical, Aero, Auto and Civil Engineering, Kalasalingam Academy of Research and Education, Krishnankoil, Virudhunagar, Tamil Nadu, India
2 shared publications M Uthayakumar
Faculty of Mechanical Engineering, Kalasalingam University, Tamil Nadu, India
2 shared publications- Narayanan Selvapalam
Center for Supramolecular Chemistry, International Research Center and Department of Chemistry, Kalasalingam Academy of Research and Education, Krishnankoil, India
2 shared publications
Latest Publications
- Open Access
- 15 March 2026
- Published by Engineering Society of Corrosion in Zastita materijala
- Vol. 67 (1) , 62-75
Investigating the hydrophobic properties and corrosion resistance of copper surfaces via octadecanoic acid chemical deposition technique
This study investigates the enhancement of copper’s hydrophobicity and corrosion resistance through the chemical deposition of octadecanoic acid. Structural and chemical modifications of the treated copper surfaces were analyzed using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Energy-Dispersive X-ray Spectroscopy (EDS). SEM images revealed significant alterations in surface topography, promoting water repellency, while EDS confirmed the uniform coating of octadecanoic acid. XRD analysis showed that the crystalline structure of copper was preserved. Hydrophobicity was quantitatively assessed through contact angle measurements, which increased from 75° for bare copper to 121.5° for the octadecanoic acid-coated copper, confirming the transition to a hydrophobic surface. Water jetting and water bouncing tests demonstrated superior water repellency and self-cleaning efficiency of the coated surfaces. The contact angle measurement for the coated surface reached approximately 160° during the bouncing tests, indicating highly hydrophobic behaviour. Corrosion resistance was evaluated using dynamic potential polarization and electrochemical impedance spectroscopy (EIS). The dynamic polarization curve indicated a corrosion potential (Ecorr) of -0.0700 V for the coated copper, compared to -0.2036 V for the uncoated copper. The corrosion current density (Icorr) for the coated copper was 3.577 × 10⁻⁶ A/cm², significantly lower than the bare copper's value of 2.214 × 10⁻⁵ A/cm². The corrosion rate of the coated copper was reduced to 1.388 × 10⁻¹ mm/a from 3.226 × 10⁻¹ mm/a for the uncoated copper, resulting in an efficiency of 83.8%. These findings demonstrate that octadecanoic acid is an effective and cost-efficient protective coating for enhancing copper's durability and functionality, especially in moisture-prone environments.
- 15 March 2026
- Published by Engineering Society of Corrosion in Zastita materijala
- Vol. 67 (1) , 62-75
Open AccessInvestigating the hydrophobic properties and corrosion resistance of copper surfaces via octadecanoic acid chemical deposition technique
This study investigates the enhancement of copper’s hydrophobicity and corrosion resistance through the chemical deposition of octadecanoic acid. Structural and chemical modifications of the treated copper surfaces were analyzed using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Energy-Dispersive X-ray Spectroscopy (EDS). SEM images revealed significant alterations in surface topography, promoting water repellency, while EDS confirmed the uniform coating of octadecanoic acid. XRD analysis showed that the crystalline structure of copper was preserved. Hydrophobicity was quantitatively assessed through contact angle measurements, which increased from 75° for bare copper to 121.5° for the octadecanoic acid-coated copper, confirming the transition to a hydrophobic surface. Water jetting and water bouncing tests demonstrated superior water repellency and self-cleaning efficiency of the coated surfaces. The contact angle measurement for the coated surface reached approximately 160° during the bouncing tests, indicating highly hydrophobic behaviour. Corrosion resistance was evaluated using dynamic potential polarization and electrochemical impedance spectroscopy (EIS). The dynamic polarization curve indicated a corrosion potential (Ecorr) of -0.0700 V for the coated copper, compared to -0.2036 V for the uncoated copper. The corrosion current density (Icorr) for the coated copper was 3.577 × 10⁻⁶ A/cm², significantly lower than the bare copper's value of 2.214 × 10⁻⁵ A/cm². The corrosion rate of the coated copper was reduced to 1.388 × 10⁻¹ mm/a from 3.226 × 10⁻¹ mm/a for the uncoated copper, resulting in an efficiency of 83.8%. These findings demonstrate that octadecanoic acid is an effective and cost-efficient protective coating for enhancing copper's durability and functionality, especially in moisture-prone environments.
- Open Access
- 12 January 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (1) , 91-106
Evaluation of corrosion mitigation of SS904l using inhibitors with statistical and morphological analysis
This study evaluates the corrosion resistance of SS904L stainless steel, a highly alloyed material known for its exceptional performance in acidic environments, to address the need for optimized corrosion mitigation strategies. Corrosion inhibitors were utilized to enhance the material's durability, with the weight loss method employed to assess corrosion under varying conditions of temperature and pressure. Experiments tested inhibitor concentrations ranging from 0”“5 mg per 100 mL over exposure durations of 24, 48, and 72 hours. Statistical analyses using ANOVA and regression confirmed a significant improvement in corrosion resistance with appropriate inhibitor concentrations. The Kesternich test provided comparative insights into the corrosion rate, validating the inhibitors' efficacy under simulated harsh conditions. Morphological analyses via X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) revealed the formation of protective layers on the metal surface, contributing to enhanced durability. These findings emphasize the critical role of corrosion inhibitors in extending the service life of SS904L and establish a relationship between inhibitor concentration, exposure time, and corrosion performance, paving the way for advanced corrosion mitigation strategies.
- 12 January 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (1) , 91-106
Open AccessEvaluation of corrosion mitigation of SS904l using inhibitors with statistical and morphological analysis
This study evaluates the corrosion resistance of SS904L stainless steel, a highly alloyed material known for its exceptional performance in acidic environments, to address the need for optimized corrosion mitigation strategies. Corrosion inhibitors were utilized to enhance the material's durability, with the weight loss method employed to assess corrosion under varying conditions of temperature and pressure. Experiments tested inhibitor concentrations ranging from 0”“5 mg per 100 mL over exposure durations of 24, 48, and 72 hours. Statistical analyses using ANOVA and regression confirmed a significant improvement in corrosion resistance with appropriate inhibitor concentrations. The Kesternich test provided comparative insights into the corrosion rate, validating the inhibitors' efficacy under simulated harsh conditions. Morphological analyses via X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) revealed the formation of protective layers on the metal surface, contributing to enhanced durability. These findings emphasize the critical role of corrosion inhibitors in extending the service life of SS904L and establish a relationship between inhibitor concentration, exposure time, and corrosion performance, paving the way for advanced corrosion mitigation strategies.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30, e20240647
Enhanced corrosion resistance of copper for agricultural equipment using superhydrophobic stearic acid coatings
Significant risks of corrosion and wear are associated with agricultural equipment’s continuous exposure to fertilizers harsh chemicals and moisture. These chemicals hasten the deterioration of metal components thereby decreasing the machinery’s operational lifespan and leading to physical harm such as surface cracks and holes. Utilizing efficient corrosion protection methods is crucial to lessening these adverse consequences. In order to solve this, the current study investigates a corrosion prevention technique that involves coating copper with stearic acid to produce a superhydrophobic surface. To create this protective coating copper samples were cleaned and then left to soak for 72 hours at room temperature in a stearic acid solution. Utilizing energy-dispersive X-ray spectroscopy (EDX) and scanning electron microscopy (SEM) post-treatment analysis of the copper surfaces revealed a notable improvement in corrosion and wear resistance. The development of a hydrophobic microstructure was validated by SEM images and the successful deposition of the stearic acid was indicated by an 88 percent increase in carbon content in the EDX results. The high anti-wettability of the coating was demonstrated by performance tests which included water bouncing jetting and self-cleaning assessments. This technique also offers an eco-friendly corrosion prevention solution because stearic acid comes from natural sources. The results highlight the potential of stearic acid coatings to decrease metal loss from corrosion and increase the useful life and efficiency of agricultural equipment.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30, e20240647
Open AccessEnhanced corrosion resistance of copper for agricultural equipment using superhydrophobic stearic acid coatings
Significant risks of corrosion and wear are associated with agricultural equipment’s continuous exposure to fertilizers harsh chemicals and moisture. These chemicals hasten the deterioration of metal components thereby decreasing the machinery’s operational lifespan and leading to physical harm such as surface cracks and holes. Utilizing efficient corrosion protection methods is crucial to lessening these adverse consequences. In order to solve this, the current study investigates a corrosion prevention technique that involves coating copper with stearic acid to produce a superhydrophobic surface. To create this protective coating copper samples were cleaned and then left to soak for 72 hours at room temperature in a stearic acid solution. Utilizing energy-dispersive X-ray spectroscopy (EDX) and scanning electron microscopy (SEM) post-treatment analysis of the copper surfaces revealed a notable improvement in corrosion and wear resistance. The development of a hydrophobic microstructure was validated by SEM images and the successful deposition of the stearic acid was indicated by an 88 percent increase in carbon content in the EDX results. The high anti-wettability of the coating was demonstrated by performance tests which included water bouncing jetting and self-cleaning assessments. This technique also offers an eco-friendly corrosion prevention solution because stearic acid comes from natural sources. The results highlight the potential of stearic acid coatings to decrease metal loss from corrosion and increase the useful life and efficiency of agricultural equipment.
- 31 July 2023
- Published by Springer Nature
- p. 249-260
A Novel Design and Development of Low-Cost Electro-Chemical Machining Unit with Optimized Parameters
- 31 July 2023
- Published by Springer Nature
- p. 249-260
A Novel Design and Development of Low-Cost Electro-Chemical Machining Unit with Optimized Parameters
- Open Access
- 28 July 2023
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 10, 1240606
Augmenting the double pipe heat exchanger efficiency using varied molar Ag ornamented graphene oxide (GO) nanoparticles aqueous hybrid nanofluids
The optimization of heat transfer in heat exchanging equipment is paramount for the efficient management of energy resources in both industrial and residential settings. In pursuit of this goal, this empirical study embarked on enhancing the heat transfer performance of a double pipe heat exchanger (DPHX) by introducing silver (Ag)-graphene oxide (GO) hybrid nanofluids into the annulus of the heat exchanger. To achieve this, three distinct molar concentrations of Ag ornamented GO hybrid nanoparticles were synthesized by blending GO nanoparticles with silver nitrate at molarities of 0.03 M, 0.06 M, and 0.09 M. These Ag-GO hybrid nanoparticles were then dispersed in the base fluid, resulting in the formation of three distinct hybrid nanofluids, each with a consistent weight percentage of 0.05 wt%. Thorough characterization and evaluation of thermophysical properties were performed on the resulting hybrid nanomaterials and nanofluids, respectively. Remarkably, the most significant enhancement in heat transfer coefficient, Nusselt number, and thermal performance index (62.9%, 33.55%, and 1.29, respectively) was observed with the 0.09 M Ag-GO hybrid nanofluid, operating at a Reynolds number of 1,451 and a flow rate of 47 g/s. These findings highlight the substantial improvement in thermophysical properties of the base fluid and the intensification of heat transfer in the DPHX with increasing Ag molarity over GO. In summary, this study emphasizes the vital importance of optimizing the molarity of the material, which also plays a significant role in nanoparticle synthesis to achieve the optimal amplification of heat transfer.
- 28 July 2023
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 10, 1240606
Open AccessAugmenting the double pipe heat exchanger efficiency using varied molar Ag ornamented graphene oxide (GO) nanoparticles aqueous hybrid nanofluids
The optimization of heat transfer in heat exchanging equipment is paramount for the efficient management of energy resources in both industrial and residential settings. In pursuit of this goal, this empirical study embarked on enhancing the heat transfer performance of a double pipe heat exchanger (DPHX) by introducing silver (Ag)-graphene oxide (GO) hybrid nanofluids into the annulus of the heat exchanger. To achieve this, three distinct molar concentrations of Ag ornamented GO hybrid nanoparticles were synthesized by blending GO nanoparticles with silver nitrate at molarities of 0.03 M, 0.06 M, and 0.09 M. These Ag-GO hybrid nanoparticles were then dispersed in the base fluid, resulting in the formation of three distinct hybrid nanofluids, each with a consistent weight percentage of 0.05 wt%. Thorough characterization and evaluation of thermophysical properties were performed on the resulting hybrid nanomaterials and nanofluids, respectively. Remarkably, the most significant enhancement in heat transfer coefficient, Nusselt number, and thermal performance index (62.9%, 33.55%, and 1.29, respectively) was observed with the 0.09 M Ag-GO hybrid nanofluid, operating at a Reynolds number of 1,451 and a flow rate of 47 g/s. These findings highlight the substantial improvement in thermophysical properties of the base fluid and the intensification of heat transfer in the DPHX with increasing Ag molarity over GO. In summary, this study emphasizes the vital importance of optimizing the molarity of the material, which also plays a significant role in nanoparticle synthesis to achieve the optimal amplification of heat transfer.
- Open Access
- 7 January 2020
- Published by SAGE Publications in Measurement and Control
- Vol. 53 (3-4) , 390-399
Experimental investigation on heat transfer augmentation of transverse twisted tapes in a confined rectangular channel
This study investigates the influence of twisted tape inserts on a flow pathway in transverse direction of a flow situation. An array of twisted tapes was mounted on the confined channel to disturb the flow to enhance the heat transfer. The test section had 20 twisted tapes of 35-mm height, 10-mm width and a twist angle of 180° mounted on a silica gel–coated plate. Experiments were conducted on the fabricated experimental setup for different discharge conditions. The Reynolds number considered for the study ranged from 2300 to 3500, and the heat inputs varied from 50 to 250 W, with an interval of 50 W. To visualize the presence of twisted tapes on the flow path, the rectangular channel was visualized by laser flow visualization method, which reported the impact of the twisted tapes on the flow. The existence of twisted tape affects the flow, and it forms a swirl that provides a proper mixing of fluid to enhance heat transfer. The outcome of the present investigation provides a solution to enhance heat transfer and proposes the use of twisted tapes instead of using segmented fins in design of fins.
- 7 January 2020
- Published by SAGE Publications in Measurement and Control
- Vol. 53 (3-4) , 390-399
Open AccessExperimental investigation on heat transfer augmentation of transverse twisted tapes in a confined rectangular channel
This study investigates the influence of twisted tape inserts on a flow pathway in transverse direction of a flow situation. An array of twisted tapes was mounted on the confined channel to disturb the flow to enhance the heat transfer. The test section had 20 twisted tapes of 35-mm height, 10-mm width and a twist angle of 180° mounted on a silica gel–coated plate. Experiments were conducted on the fabricated experimental setup for different discharge conditions. The Reynolds number considered for the study ranged from 2300 to 3500, and the heat inputs varied from 50 to 250 W, with an interval of 50 W. To visualize the presence of twisted tapes on the flow path, the rectangular channel was visualized by laser flow visualization method, which reported the impact of the twisted tapes on the flow. The existence of twisted tape affects the flow, and it forms a swirl that provides a proper mixing of fluid to enhance heat transfer. The outcome of the present investigation provides a solution to enhance heat transfer and proposes the use of twisted tapes instead of using segmented fins in design of fins.
- Open Access
- 1 August 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1276 (1) , 012013
Numerical analysis of drag and lift coefficient of a Sport Utility Vehicle (SUV)
The paper describes the modeling and analysis of a Sport Utility Vehicle (SUV). The present study mainly focuses on the reduction of aerodynamics drag and lift coefficient of a car, which helps to improve the vehicle performance and fuel efficiency. Usually the aerodynamic drag and lift is insignificant at low vehicle speed but the magnitude of air resistance becomes considerable with accelerating the vehicle. The Computational Fluid Dynamics (CFD) helps to analyze the flow stream around a SUV. The modeling software is used to design a 3D car model and the flow stream is analyzed by ANSYS Fluent. Initially, the first model was analyzed at various velocity conditions using Reynolds-Averaged Navier–Stokes (RANS) with standard k-ε model. The basic model of SUV has a drag coefficient and lift coefficient value of 0.62 and 0.099 respectively. Initially the first model is designed by introducing air splitter on roof and based on the results the second model is designed by introducing 15 degree boat tailing angle with first model. The drag reduction is reduced by 6.45% for first model and 19.35% for second model compared to the base model. Similarly, the lift coefficient is reduced by 2.02% for first model and 30.30% for the second model. Moreover the second model produces low drag and lift coefficient than first and base model. A significant reduction is observed in first model when compared to the base model. The vector plots are used to examine the streamline path of both the models.
- 1 August 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1276 (1) , 012013
Open AccessNumerical analysis of drag and lift coefficient of a Sport Utility Vehicle (SUV)
The paper describes the modeling and analysis of a Sport Utility Vehicle (SUV). The present study mainly focuses on the reduction of aerodynamics drag and lift coefficient of a car, which helps to improve the vehicle performance and fuel efficiency. Usually the aerodynamic drag and lift is insignificant at low vehicle speed but the magnitude of air resistance becomes considerable with accelerating the vehicle. The Computational Fluid Dynamics (CFD) helps to analyze the flow stream around a SUV. The modeling software is used to design a 3D car model and the flow stream is analyzed by ANSYS Fluent. Initially, the first model was analyzed at various velocity conditions using Reynolds-Averaged Navier–Stokes (RANS) with standard k-ε model. The basic model of SUV has a drag coefficient and lift coefficient value of 0.62 and 0.099 respectively. Initially the first model is designed by introducing air splitter on roof and based on the results the second model is designed by introducing 15 degree boat tailing angle with first model. The drag reduction is reduced by 6.45% for first model and 19.35% for second model compared to the base model. Similarly, the lift coefficient is reduced by 2.02% for first model and 30.30% for the second model. Moreover the second model produces low drag and lift coefficient than first and base model. A significant reduction is observed in first model when compared to the base model. The vector plots are used to examine the streamline path of both the models.
- 25 January 2019
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 42 (6) , 672-681
Heat transfer behaviour on influence of an adiabatic section on concentric tube shell assisted heat pipe heat exchanger
Influence on thermal performances of the concentric tube shell assisted heat-pipe heat exchanger with and without adiabatic section has been experimentally investigated. Water is used as heat-carrying fluid and methanol is used as working fluid in the heat pipe.Mass flow rates of hot water ranges from 30 lph to 70 lph, for cold water 15 lph to 35 lph and during the investigation the temperature of the hot water at inlet is ranges 50°C to 60°C. For various mass flow rate and inlet temperature the heat transfer coefficient, heat transfer rate and effectiveness of the heat exchanger are reported. The mass flow rate of hot and cold water is 70lph and 35lph and inlet hot water at 60°C, the effectiveness of heat pipe without adiabatic section is 26.9%.The investigation reveals that there is an increase in effectiveness by 11.2% is obtained in without adiabatic section, compared to with adiabatic section.
- 25 January 2019
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 42 (6) , 672-681
Heat transfer behaviour on influence of an adiabatic section on concentric tube shell assisted heat pipe heat exchanger
Influence on thermal performances of the concentric tube shell assisted heat-pipe heat exchanger with and without adiabatic section has been experimentally investigated. Water is used as heat-carrying fluid and methanol is used as working fluid in the heat pipe.Mass flow rates of hot water ranges from 30 lph to 70 lph, for cold water 15 lph to 35 lph and during the investigation the temperature of the hot water at inlet is ranges 50°C to 60°C. For various mass flow rate and inlet temperature the heat transfer coefficient, heat transfer rate and effectiveness of the heat exchanger are reported. The mass flow rate of hot and cold water is 70lph and 35lph and inlet hot water at 60°C, the effectiveness of heat pipe without adiabatic section is 26.9%.The investigation reveals that there is an increase in effectiveness by 11.2% is obtained in without adiabatic section, compared to with adiabatic section.
- 8 February 2018
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 40 (8) , 847-853
Experimental investigation on heat transfer enhancement in a minichannel using CuO-water nanofluid
In this work, CuO-water nanofluid with an average size of nanoparticles (24 nm) and volume concentrations of 0.1% and 0.5% is used. For the computer microprocessor cooling, an aluminium minichannel of dimension (40 × 1 × 3) mm3 is fabricated instead of an aluminium heat sink and a cooling fan. It is shown that the dispersion of nanoparticles into the distilled water has produced a considerable enhancement of the cooling of the minichannel. Experiments were conducted for Reynolds number ranging from 25 to 800 under a laminar regime. From the experiments, it is found that better heat transfer is achieved when CuO-water nanofluid is used as the working fluid.
- 8 February 2018
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 40 (8) , 847-853
Experimental investigation on heat transfer enhancement in a minichannel using CuO-water nanofluid
In this work, CuO-water nanofluid with an average size of nanoparticles (24 nm) and volume concentrations of 0.1% and 0.5% is used. For the computer microprocessor cooling, an aluminium minichannel of dimension (40 × 1 × 3) mm3 is fabricated instead of an aluminium heat sink and a cooling fan. It is shown that the dispersion of nanoparticles into the distilled water has produced a considerable enhancement of the cooling of the minichannel. Experiments were conducted for Reynolds number ranging from 25 to 800 under a laminar regime. From the experiments, it is found that better heat transfer is achieved when CuO-water nanofluid is used as the working fluid.