Saleh Issa Khassaf
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Saleh Issa Khassaf has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Zahraa Khalid Shuhaib
Civil Engineering Department, University of Basrah, Basrah, Iraq
2 shared publications - Abdul Aziz A. Al-Kifae1 shared publication
- Abdulazeez A. Al-Kifaee
Civil Engineering Department, Al-Nahrain University, Baghdad, Iraq
1 shared publication - Ahmed Ashor Al-Saadi1 shared publication
- Ali M. Madhloom
Civil Engineering Department, Al-Nahrain University, Baghdad, Iraq
1 shared publication - Ali M. Madhloom1 shared publication
Latest Publications
- Open Access
- 29 September 2026
- Published by National Institute of STEM Research in Archives for Technical Sciences
- No. 36,p. 192-211
EFFECT OF SAND SHELL IMPROVEMENT USING POLYPROPYLENE FIBER AND CEMENT ON THE SEISMIC RESPONSE OF SMALL-SCALE ZONED EARTH DAM MODELS
The application of sand as shell materials in zoned earth dams is common due to its availability and economic factors. Nevertheless, it is necessary to analyze the performance of such materials under the simultaneous effect of seepage and earthquake loads, especially when the core of the structure is formed from low permeable materials. The present work evaluates the influence of polypropylene fiber and cement additions on the seismic performance of sand-shell zoned earth dams. Three small-scale physical models with equal geometry and silty clay cores were prepared and tested using a shaking table in a laboratory. The physical models involved an unreinforced Sand–Silty clay dam, polypropylene fiber-reinforced sand-shell dam containing 0.5% fibers based on dry weight, and a cement-strengthened sand-shell dam with 3% cement content. The steady state seepage analysis was carried out at first; subsequently, the seismic test with the El Centro earthquake was carried out with the PGA values of 0.1, 0.2, 0.3, 0.4, and 0.5 g. The seepage discharge was relatively constant at values between 2.41×10⁻⁷ and 2.75×10⁻⁷ m³/s/m, confirming the dominant control of the silty clay core on the seepage process. For the applied earthquake load, the acceleration magnification, deformation, increase of pore-water pressure, and damages were highest in the untreated model. Under the acceleration of 0.5 g, the settlement on the dam's crest was 26 mm, 18 mm, and 5 mm in the untreated model, the fiber-reinforced model, and the cement-treated model, corresponding to reductions by 31% and 81%, respectively. In addition, the maximum width of cracks decreased from approximately 125 mm in the untreated model to 15 mm and 5 mm in the fiber-reinforced model and the cement-treated model, respectively. The effectiveness of stresses and factors of safety was higher for the cement-treated model than other models through the entire loading sequence. Although both improvement techniques increased the seismic resistance of the embankment, the latter had a larger decrease in deformation and damage while retaining higher stability under simultaneous effects of seepage and earthquakes.
- 29 September 2026
- Published by National Institute of STEM Research in Archives for Technical Sciences
- No. 36,p. 192-211
Open AccessEFFECT OF SAND SHELL IMPROVEMENT USING POLYPROPYLENE FIBER AND CEMENT ON THE SEISMIC RESPONSE OF SMALL-SCALE ZONED EARTH DAM MODELS
The application of sand as shell materials in zoned earth dams is common due to its availability and economic factors. Nevertheless, it is necessary to analyze the performance of such materials under the simultaneous effect of seepage and earthquake loads, especially when the core of the structure is formed from low permeable materials. The present work evaluates the influence of polypropylene fiber and cement additions on the seismic performance of sand-shell zoned earth dams. Three small-scale physical models with equal geometry and silty clay cores were prepared and tested using a shaking table in a laboratory. The physical models involved an unreinforced Sand–Silty clay dam, polypropylene fiber-reinforced sand-shell dam containing 0.5% fibers based on dry weight, and a cement-strengthened sand-shell dam with 3% cement content. The steady state seepage analysis was carried out at first; subsequently, the seismic test with the El Centro earthquake was carried out with the PGA values of 0.1, 0.2, 0.3, 0.4, and 0.5 g. The seepage discharge was relatively constant at values between 2.41×10⁻⁷ and 2.75×10⁻⁷ m³/s/m, confirming the dominant control of the silty clay core on the seepage process. For the applied earthquake load, the acceleration magnification, deformation, increase of pore-water pressure, and damages were highest in the untreated model. Under the acceleration of 0.5 g, the settlement on the dam's crest was 26 mm, 18 mm, and 5 mm in the untreated model, the fiber-reinforced model, and the cement-treated model, corresponding to reductions by 31% and 81%, respectively. In addition, the maximum width of cracks decreased from approximately 125 mm in the untreated model to 15 mm and 5 mm in the fiber-reinforced model and the cement-treated model, respectively. The effectiveness of stresses and factors of safety was higher for the cement-treated model than other models through the entire loading sequence. Although both improvement techniques increased the seismic resistance of the embankment, the latter had a larger decrease in deformation and damage while retaining higher stability under simultaneous effects of seepage and earthquakes.
- Open Access
- 19 April 2026
- Published by AMO Publisher in EJSMT
- Vol. 2 (3) , 8-21
Experimental Study of Local Scour around Different Pile Group Arrangements
Local scour around pile group foundations is a sensitive hydraulic issue which has a great impact on the stability and safety of structures resting on piles. This work is an experimental experiment of local scour behavior under conditions of clear-water flow and the local scour of various pile group configurations, specifically the effects of pile group structure on scour depth and its spatial distribution. The experiments were carried out using recirculating open-channel flume with non-cohesive uniform sediment. The arrangement of four pile groups was investigated, which include tandem, two-by-two, two-by-three, and staggered. Piles were all circular and of the same size to control the effect of arrangement. The experiments were conducted at different flow intensity ratios between 0.60 and 0.90 and a grid-based measurement system was utilized to record detailed scour profiles. The findings show that the scour depth continually increases with increasing flow intensity of all configurations tested. The highest equilibrium scour depth was measured in the 2 x 3 setup and it was about 5.3 cm at the highest flow intensity ratio of 0.90 and the staggered setup had the lowest scour depth at the same intensity ratio. It was observed using temporal analysis that about 95 percent of the overall scour depth is formed in the first two hours when the scour decreases at a much slower rate. Spatial distribution of scour was also discovered to be very skewed with the maximum scour being in the upstream piles and deposition areas developing downstream. Compared to the 2×3 arrangement, a comparative analysis showed that the staggered set-up resulted in an average scour depth reduction of approximately 20% which underscores its efficiency in the control of scour. A further empirical equation was constructed to estimate equilibrium scour depth in terms of flow intensity and pile arrangement with an overall excellent correlation with the experimental data with a coefficient of determination of about R2 = 0.984. The results of this paper highlight the important role of the pile group arrangement in local scour control and offer useful information on the design and optimization of the pile-supported hydraulic structures.
- 19 April 2026
- Published by AMO Publisher in EJSMT
- Vol. 2 (3) , 8-21
Open AccessExperimental Study of Local Scour around Different Pile Group Arrangements
Local scour around pile group foundations is a sensitive hydraulic issue which has a great impact on the stability and safety of structures resting on piles. This work is an experimental experiment of local scour behavior under conditions of clear-water flow and the local scour of various pile group configurations, specifically the effects of pile group structure on scour depth and its spatial distribution. The experiments were carried out using recirculating open-channel flume with non-cohesive uniform sediment. The arrangement of four pile groups was investigated, which include tandem, two-by-two, two-by-three, and staggered. Piles were all circular and of the same size to control the effect of arrangement. The experiments were conducted at different flow intensity ratios between 0.60 and 0.90 and a grid-based measurement system was utilized to record detailed scour profiles. The findings show that the scour depth continually increases with increasing flow intensity of all configurations tested. The highest equilibrium scour depth was measured in the 2 x 3 setup and it was about 5.3 cm at the highest flow intensity ratio of 0.90 and the staggered setup had the lowest scour depth at the same intensity ratio. It was observed using temporal analysis that about 95 percent of the overall scour depth is formed in the first two hours when the scour decreases at a much slower rate. Spatial distribution of scour was also discovered to be very skewed with the maximum scour being in the upstream piles and deposition areas developing downstream. Compared to the 2×3 arrangement, a comparative analysis showed that the staggered set-up resulted in an average scour depth reduction of approximately 20% which underscores its efficiency in the control of scour. A further empirical equation was constructed to estimate equilibrium scour depth in terms of flow intensity and pile arrangement with an overall excellent correlation with the experimental data with a coefficient of determination of about R2 = 0.984. The results of this paper highlight the important role of the pile group arrangement in local scour control and offer useful information on the design and optimization of the pile-supported hydraulic structures.
- Open Access
- 28 February 2026
- Published by Union of Iraqi Geologists (UIG) in Iraqi Geological Journal
- p. 18-35
Impact of Climate Change and Upstream Development on Domestic Water Security in the Euphrates River Basin, Iraq
Climate change and upstream water management practices increasingly threaten the sustainability of water resources for populations along the Euphrates River in Iraq. The interaction between these two variables poses a significant challenge to water security in the Euphrates Basin, limiting the water system's ability to meet future demands sustainably. This study evaluates the cumulative effects of these factors on water security in the Euphrates Basin, using the RIBASIM model to analyze three climate scenarios alongside a scenario focused on upstream development. Additionally, an integrated scenario combining severe climate change with upstream growth was examined. The findings show that as the severity of climate change rises, there is a corresponding rise in domestic water deficits and a decline in supply reliability across Al-Anbar, Baghdad, Babylon, Karbala, Al-Najaf and Al-Qadisiyah Governorates, where the Domestic Water Reliability Index varies: SSP1-2.6 (0.92 to 0.99), SSP2-4.5 (0.91 to 0.99), and SSP5-8.5 (0.88 to 0.99). Conversely, Al-Muthana and Dhi-Qar Governorates exhibit more reliability in ensuring water security; the Domestic Water Reliability Index is 0.99. Upstream development poses a greater challenge than climate change alone, leading to a notable decrease in supply efficiency and a gradual reduction in Domestic Water Reliability Index, which drops to an index of 0.71 in Al-Qadisiyah Governorate. The integrated scenario reveals significant cumulative stress from both climatic and human-induced factors, resulting in a marked decline in supply reliability and a concerning rise in water stress, with Domestic Water Reliability Index values ranging from 0.59 to 0.99. This is the most hazardous scenario for population water security. These findings emphasize the urgent need to integrate climate data into shared water resource management within a quantitative framework, providing a scientific basis for decision-makers to formulate effective adaptation strategies to ensure water security amid future climatic and regional challenges.
- 28 February 2026
- Published by Union of Iraqi Geologists (UIG) in Iraqi Geological Journal
- p. 18-35
Open AccessImpact of Climate Change and Upstream Development on Domestic Water Security in the Euphrates River Basin, Iraq
Climate change and upstream water management practices increasingly threaten the sustainability of water resources for populations along the Euphrates River in Iraq. The interaction between these two variables poses a significant challenge to water security in the Euphrates Basin, limiting the water system's ability to meet future demands sustainably. This study evaluates the cumulative effects of these factors on water security in the Euphrates Basin, using the RIBASIM model to analyze three climate scenarios alongside a scenario focused on upstream development. Additionally, an integrated scenario combining severe climate change with upstream growth was examined. The findings show that as the severity of climate change rises, there is a corresponding rise in domestic water deficits and a decline in supply reliability across Al-Anbar, Baghdad, Babylon, Karbala, Al-Najaf and Al-Qadisiyah Governorates, where the Domestic Water Reliability Index varies: SSP1-2.6 (0.92 to 0.99), SSP2-4.5 (0.91 to 0.99), and SSP5-8.5 (0.88 to 0.99). Conversely, Al-Muthana and Dhi-Qar Governorates exhibit more reliability in ensuring water security; the Domestic Water Reliability Index is 0.99. Upstream development poses a greater challenge than climate change alone, leading to a notable decrease in supply efficiency and a gradual reduction in Domestic Water Reliability Index, which drops to an index of 0.71 in Al-Qadisiyah Governorate. The integrated scenario reveals significant cumulative stress from both climatic and human-induced factors, resulting in a marked decline in supply reliability and a concerning rise in water stress, with Domestic Water Reliability Index values ranging from 0.59 to 0.99. This is the most hazardous scenario for population water security. These findings emphasize the urgent need to integrate climate data into shared water resource management within a quantitative framework, providing a scientific basis for decision-makers to formulate effective adaptation strategies to ensure water security amid future climatic and regional challenges.
- 1 January 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (1) , 65-77
Seepage Control in Zoned Earth Dams Using Lime–Fly Ash Treated Sandy Soil
Seepage control is a critical factor in ensuring the stability of earth dams, particularly those constructed with permeable soils. Uncontrolled seepage and increased pore pressures within the dam body are typically associated with instability, internal erosion, and potential failure. This study aims to evaluate the effectiveness of lime–fly ash mixtures in controlling seepage through earth dams constructed with sandy soil, using experimental modelling and numerical simulation. A physical model of a zoned earth dam was built using untreated sandy soil as the control model, along with treated models in which the sandy core was stabilized with progressively higher lime–fly ash proportions. The results of laboratory permeability tests demonstrated significant reductions in hydraulic conductivity with increasing additive content, resulting in delayed steady-state conditions and a reduction of up to 98.2% in seepage rate compared with the control model. Numerical simulations, validated against experimental results (coefficient of determination, R²>0.98), accurately reproduced phreatic lines and seepage rates and were further used to examine the influence of core slope geometry. The results showed that a core slope of 0.75:1 provided nearly equivalent hydraulic performance to that of the baseline 1:1 slope, offering a more cost-effective alternative. These findings highlight the potential of lime–fly ash–sand mixtures as sustainable and cost-efficient alternatives for dam cores, particularly in regions where clay resources are limited.
- 1 January 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (1) , 65-77
Seepage Control in Zoned Earth Dams Using Lime–Fly Ash Treated Sandy Soil
Seepage control is a critical factor in ensuring the stability of earth dams, particularly those constructed with permeable soils. Uncontrolled seepage and increased pore pressures within the dam body are typically associated with instability, internal erosion, and potential failure. This study aims to evaluate the effectiveness of lime–fly ash mixtures in controlling seepage through earth dams constructed with sandy soil, using experimental modelling and numerical simulation. A physical model of a zoned earth dam was built using untreated sandy soil as the control model, along with treated models in which the sandy core was stabilized with progressively higher lime–fly ash proportions. The results of laboratory permeability tests demonstrated significant reductions in hydraulic conductivity with increasing additive content, resulting in delayed steady-state conditions and a reduction of up to 98.2% in seepage rate compared with the control model. Numerical simulations, validated against experimental results (coefficient of determination, R²>0.98), accurately reproduced phreatic lines and seepage rates and were further used to examine the influence of core slope geometry. The results showed that a core slope of 0.75:1 provided nearly equivalent hydraulic performance to that of the baseline 1:1 slope, offering a more cost-effective alternative. These findings highlight the potential of lime–fly ash–sand mixtures as sustainable and cost-efficient alternatives for dam cores, particularly in regions where clay resources are limited.
- Open Access
- 1 November 2025
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1545 (1)
Controlling the Seepage Issue in an Earth Dams: A Review
Seepage control in earth dams is crucial for maintaining its structural integrity and ensuring its long-term performance. Seepage refers to the flow of water through or under the dam, which can lead to erosion, internal instability, or even failure if not properly controlled. This literature review explores various chemical additives, methods, and materials employed to mitigate seepage in earth dams, encompassing both traditional techniques and modern advancements. This study aims to review and compare various methods and techniques used for seepage control based on the literature from reputable journal websites. According to the article reviews, the use of large proportions of recycled plastic materials to decrease the seepage flow rate in earthen dams is an impractical option, and the use of geometrical features of the dam design to control seepage is an essential part of ensuring the safety and longevity of the dam, and that the clay core of earth dams can be strengthened by adding a percentage of chemical additives. Sandy soils can also be used when economics permits the use of larger quantities of additives required for stability and erosion resistance.
- 1 November 2025
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1545 (1)
Open AccessControlling the Seepage Issue in an Earth Dams: A Review
Seepage control in earth dams is crucial for maintaining its structural integrity and ensuring its long-term performance. Seepage refers to the flow of water through or under the dam, which can lead to erosion, internal instability, or even failure if not properly controlled. This literature review explores various chemical additives, methods, and materials employed to mitigate seepage in earth dams, encompassing both traditional techniques and modern advancements. This study aims to review and compare various methods and techniques used for seepage control based on the literature from reputable journal websites. According to the article reviews, the use of large proportions of recycled plastic materials to decrease the seepage flow rate in earthen dams is an impractical option, and the use of geometrical features of the dam design to control seepage is an essential part of ensuring the safety and longevity of the dam, and that the clay core of earth dams can be strengthened by adding a percentage of chemical additives. Sandy soils can also be used when economics permits the use of larger quantities of additives required for stability and erosion resistance.
- Open Access
- 1 August 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (8) , 3126-3150
Statistical Analyses of the Euphrates River Entry and Hydrological Drought Assessment (SDI)
The Euphrates River, a vital water resource in Iraq, has seen a marked decline in flow over the past two decades due to climate change and upstream interventions. The aim of this study is to investigate the impacts of changing rainfall patterns and temperature on the river's water balance, flow regime, and drought index. Results show an annual rainfall decline of 0.15 mm, while maximum and minimum temperatures increased annually by 0.086°C and 0.066°C, respectively, according to the Mann-Kendall trend and Sen’s slope tests. Monthly rainfall generally decreased, except for slight increases in April (0.32 mm) and October (0.018 mm). July 2017 and August 2003 saw peak temperatures of 45.1°C, while January 2008 recorded a minimum of -1.8°C. The box-and-whisker plot revealed high rainfall variability in November and February. River flow dropped by 41%, mainly due to the Turkish GAP project and climate impacts. HEC-DSS software analyzed flow duration over 32 years, and Pearson’s correlation showed low associations between flow rate and temperature (-0.36) and rainfall (0.29). The Drinc program was utilized to calculate the Standardized Drought Index, which identified that the water year 1987–1988 was very wet, while it detected severe droughts in 2014–2015 and 2021–2022. Overall, climate change and upstream dam construction have significantly reduced Euphrates River discharges, intensifying drought conditions in the region. The long-term changes in precipitation and air temperature in the study area support the observed streamflow trends. The findings of this study demonstrate that a cooperative approach to international water management between the riparian states is crucial.
- 1 August 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (8) , 3126-3150
Open AccessStatistical Analyses of the Euphrates River Entry and Hydrological Drought Assessment (SDI)
The Euphrates River, a vital water resource in Iraq, has seen a marked decline in flow over the past two decades due to climate change and upstream interventions. The aim of this study is to investigate the impacts of changing rainfall patterns and temperature on the river's water balance, flow regime, and drought index. Results show an annual rainfall decline of 0.15 mm, while maximum and minimum temperatures increased annually by 0.086°C and 0.066°C, respectively, according to the Mann-Kendall trend and Sen’s slope tests. Monthly rainfall generally decreased, except for slight increases in April (0.32 mm) and October (0.018 mm). July 2017 and August 2003 saw peak temperatures of 45.1°C, while January 2008 recorded a minimum of -1.8°C. The box-and-whisker plot revealed high rainfall variability in November and February. River flow dropped by 41%, mainly due to the Turkish GAP project and climate impacts. HEC-DSS software analyzed flow duration over 32 years, and Pearson’s correlation showed low associations between flow rate and temperature (-0.36) and rainfall (0.29). The Drinc program was utilized to calculate the Standardized Drought Index, which identified that the water year 1987–1988 was very wet, while it detected severe droughts in 2014–2015 and 2021–2022. Overall, climate change and upstream dam construction have significantly reduced Euphrates River discharges, intensifying drought conditions in the region. The long-term changes in precipitation and air temperature in the study area support the observed streamflow trends. The findings of this study demonstrate that a cooperative approach to international water management between the riparian states is crucial.
- Open Access
- 3 October 2024
- Published by IntechOpen
Dynamic Response Analysis of Coastal Bridge Members Exposed to Water Forces and Earthquakes
Reinforced concrete pile foundations are a common and efficient solution for constructing deepwater bridges that span large bodies of water, such as rivers, seas, or portions of oceans. Many of these bridges are situated in areas with significant seismic hazards. These structures are not only subjected to typical water loads, such as currents and waves but also to earthquake forces. The interaction between these water forces and the structure generates hydrodynamic forces on the submerged parts of the bridges. Thus, accurately estimating these hydrodynamic forces during earthquakes is crucial for ensuring the structural safety of deepwater bridges. This chapter aims to assess the structural response of pile foundation bridge piers when exposed to hydrodynamic forces during earthquakes, utilizing DIANA FE software and parallel computation technology. The study model incorporates the combined effects of currents, waves, and earthquakes, along with the nonlinear behavior of soil and concrete. Using Stokes’s fifth-order wave theory and Morison’s hydrodynamic pressure formula, the wave force was applied as a distributed load on the bridge’s pile foundation. The dynamic excitation characteristics of the pier under elastic conditions were analyzed, considering the influence of currents and waves.
- 3 October 2024
- Published by IntechOpen
Open AccessDynamic Response Analysis of Coastal Bridge Members Exposed to Water Forces and Earthquakes
Reinforced concrete pile foundations are a common and efficient solution for constructing deepwater bridges that span large bodies of water, such as rivers, seas, or portions of oceans. Many of these bridges are situated in areas with significant seismic hazards. These structures are not only subjected to typical water loads, such as currents and waves but also to earthquake forces. The interaction between these water forces and the structure generates hydrodynamic forces on the submerged parts of the bridges. Thus, accurately estimating these hydrodynamic forces during earthquakes is crucial for ensuring the structural safety of deepwater bridges. This chapter aims to assess the structural response of pile foundation bridge piers when exposed to hydrodynamic forces during earthquakes, utilizing DIANA FE software and parallel computation technology. The study model incorporates the combined effects of currents, waves, and earthquakes, along with the nonlinear behavior of soil and concrete. Using Stokes’s fifth-order wave theory and Morison’s hydrodynamic pressure formula, the wave force was applied as a distributed load on the bridge’s pile foundation. The dynamic excitation characteristics of the pier under elastic conditions were analyzed, considering the influence of currents and waves.
- Open Access
- 6 July 2024
- Published by Tikrit University in Tikrit Journal of Engineering Sciences
- Vol. 31 (3) , 93-104
Evaluating the Hydraulic Performance of USBR II Stilling Basin with Rough Bed
Stilling basins are built in conjunction with dams, weirs, and gates to dissipate the high kinetic energy of incoming flow and prevent severe scouring of the downstream riverbed. Dissipation of this high energy can be achieved through forming a hydraulic jump. The hydraulic jump features, including the relative length, ratio of sequent depth, and energy dissipation, are utilized as criteria to evaluate the efficiency of the stilling basin operation. The present study involved conducting experimental and numerical tests to evaluate the performance of the USBR II stilling basin downstream of an ogee spillway using six upstream Froude numbers ranging between 6.37 and 14.97. Experiments were conducted for the Typified USBR II stilling basin. The results were used to perform mesh sensitivity for numerical simulation. The USBRII stilling basin with different rough beds was numerically simulated using FLOW-3D software. The rough beds were designed using three roughness intensities, 10%, 15%, and 22%, and three relative roughness heights: 1, 0.75. and 1. According to the numerical results, distributing staggered cubic elements in the bed of the USBR II stilling basin at 10% intensity and a relative roughness height of (1) enhanced the stilling basin performance compared to the smooth bed and other rough beds. In the case of the best roughness bed, the sequent depth ratio decreased by about 12.1%, and the energy dissipation enhanced by around 5.1% compared to the Typified basin.
- 6 July 2024
- Published by Tikrit University in Tikrit Journal of Engineering Sciences
- Vol. 31 (3) , 93-104
Open AccessEvaluating the Hydraulic Performance of USBR II Stilling Basin with Rough Bed
Stilling basins are built in conjunction with dams, weirs, and gates to dissipate the high kinetic energy of incoming flow and prevent severe scouring of the downstream riverbed. Dissipation of this high energy can be achieved through forming a hydraulic jump. The hydraulic jump features, including the relative length, ratio of sequent depth, and energy dissipation, are utilized as criteria to evaluate the efficiency of the stilling basin operation. The present study involved conducting experimental and numerical tests to evaluate the performance of the USBR II stilling basin downstream of an ogee spillway using six upstream Froude numbers ranging between 6.37 and 14.97. Experiments were conducted for the Typified USBR II stilling basin. The results were used to perform mesh sensitivity for numerical simulation. The USBRII stilling basin with different rough beds was numerically simulated using FLOW-3D software. The rough beds were designed using three roughness intensities, 10%, 15%, and 22%, and three relative roughness heights: 1, 0.75. and 1. According to the numerical results, distributing staggered cubic elements in the bed of the USBR II stilling basin at 10% intensity and a relative roughness height of (1) enhanced the stilling basin performance compared to the smooth bed and other rough beds. In the case of the best roughness bed, the sequent depth ratio decreased by about 12.1%, and the energy dissipation enhanced by around 5.1% compared to the Typified basin.
- Open Access
- 1 January 2024
- Published by Walter de Gruyter GmbH in Open Engineering
- Vol. 14 (1)
Numerical study on discharge capacity of piano key side weir with various ratios of the crest length to the width
A side or lateral weir can be defined as a longitudinal weir put in parallel to the main flow direction. A piano key side weir (PKSW) is one of the various side weirs used to control flow level, flow diversion, and flood harm prevention in dams and hydraulic systems. A side weir aims to keep the water level in the main channel at a specific level by discharging the overflow water into a side channel. The discharge coefficient of the PKSW was covered in this study by numerical modeling of a rectangular PKSW type B with various ratios of the crest length to the width in a straight channel. Results showed that the discharge coefficient of the PKSW was more affected by the L/W parameter when the other parameters were constant. It was noted that the PKSW discharge coefficient for L/W equal to 6 demonstrated a significantly higher level of performance and also found that increasing the upstream head above the side weir crest (h a/P) negatively affected the coefficient of discharge. It was concluded that a high capacity of the discharge coefficient required the (h a/P) ratio to be smaller than 0.75 or within the range (0.3 ≤ h a/P < 0.75).
- 1 January 2024
- Published by Walter de Gruyter GmbH in Open Engineering
- Vol. 14 (1)
Open AccessNumerical study on discharge capacity of piano key side weir with various ratios of the crest length to the width
A side or lateral weir can be defined as a longitudinal weir put in parallel to the main flow direction. A piano key side weir (PKSW) is one of the various side weirs used to control flow level, flow diversion, and flood harm prevention in dams and hydraulic systems. A side weir aims to keep the water level in the main channel at a specific level by discharging the overflow water into a side channel. The discharge coefficient of the PKSW was covered in this study by numerical modeling of a rectangular PKSW type B with various ratios of the crest length to the width in a straight channel. Results showed that the discharge coefficient of the PKSW was more affected by the L/W parameter when the other parameters were constant. It was noted that the PKSW discharge coefficient for L/W equal to 6 demonstrated a significantly higher level of performance and also found that increasing the upstream head above the side weir crest (h a/P) negatively affected the coefficient of discharge. It was concluded that a high capacity of the discharge coefficient required the (h a/P) ratio to be smaller than 0.75 or within the range (0.3 ≤ h a/P < 0.75).
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2864 (1)
Review of earth dams research combining with seepage and stability
Water supply, energy production, flood control, and irrigation are all possible uses for embankment dams. Seepage is one of the primary reasons for the embankment dam failure. Numerical analysis and computer tools are commonly used to simulate a diversity of seepage flow conditions in earth dams. An embankment dam’s numerical analysis is a procedure in which the challenge is represented in the real world and explained in abstract form. The major numerical techniques typically utilized in the field of computational mechanics are the finite difference (FD), finite element (FE), and boundary element (BE). The use of mathematical modeling to predict seepage in earth dams was presented in this work. MODFLOW, GOESTUDIO, ANSYS, PLAXIS, PDEase2D, SVFLUX, and other software used to analyze embankment dams were covered.
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2864 (1)
Open AccessReview of earth dams research combining with seepage and stability
Water supply, energy production, flood control, and irrigation are all possible uses for embankment dams. Seepage is one of the primary reasons for the embankment dam failure. Numerical analysis and computer tools are commonly used to simulate a diversity of seepage flow conditions in earth dams. An embankment dam’s numerical analysis is a procedure in which the challenge is represented in the real world and explained in abstract form. The major numerical techniques typically utilized in the field of computational mechanics are the finite difference (FD), finite element (FE), and boundary element (BE). The use of mathematical modeling to predict seepage in earth dams was presented in this work. MODFLOW, GOESTUDIO, ANSYS, PLAXIS, PDEase2D, SVFLUX, and other software used to analyze embankment dams were covered.