Zico Alaia Akbar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zico Alaia Akbar has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Sung-Yeon Jang
Kookmin University
4 shared publications- Sung-Yeon Jang
School of Energy and Chemical Engineering Ulsan National Institute of Science and Technology (UNIST) 50 UNIST‐gil Ulsan 44919 Republic of Korea
4 shared publications Han-Ik Joh
3 shared publicationsJae-Seon Lee
3 shared publicationsSungho Lee
2 shared publicationsAgus Hadi S. Wargadipura
Center for Material Technology, Agency for Assessment and Application of Technology (BPPT), BPPT Building II 22F, M.H. Thamrin Street No. 8 Jakarta 10340, Indonesia
1 shared publication
Latest Publications
- Top Cited Papers
- 17 July 2019
- Published by Springer Nature in Nature
- Vol. 572 (7771) , 628-633
Thermal conductance of single-molecule junctions
Single-molecule junctions have been extensively used to probe properties as diverse as electrical conduction1-3, light emission4, thermoelectric energy conversion5,6, quantum interference7,8, heat dissipation9,10 and electronic noise11 at atomic and molecular scales. However, a key quantity of current interest-the thermal conductance of single-molecule junctions-has not yet been directly experimentally determined, owing to the challenge of detecting minute heat currents at the picowatt level. Here we show that picowatt-resolution scanning probes previously developed to study the thermal conductance of single-metal-atom junctions12, when used in conjunction with a time-averaging measurement scheme to increase the signal-to-noise ratio, also allow quantification of the much lower thermal conductance of single-molecule junctions. Our experiments on prototypical Au-alkanedithiol-Au junctions containing two to ten carbon atoms confirm that thermal conductance is to a first approximation independent of molecular length, consistent with detailed ab initio simulations. We anticipate that our approach will enable systematic exploration of thermal transport in many other one-dimensional systems, such as short molecules and polymer chains, for which computational predictions of thermal conductance13-16 have remained experimentally inaccessible.
- 17 July 2019
- Published by Springer Nature in Nature
- Vol. 572 (7771) , 628-633
Top Cited PapersThermal conductance of single-molecule junctions
Single-molecule junctions have been extensively used to probe properties as diverse as electrical conduction1-3, light emission4, thermoelectric energy conversion5,6, quantum interference7,8, heat dissipation9,10 and electronic noise11 at atomic and molecular scales. However, a key quantity of current interest-the thermal conductance of single-molecule junctions-has not yet been directly experimentally determined, owing to the challenge of detecting minute heat currents at the picowatt level. Here we show that picowatt-resolution scanning probes previously developed to study the thermal conductance of single-metal-atom junctions12, when used in conjunction with a time-averaging measurement scheme to increase the signal-to-noise ratio, also allow quantification of the much lower thermal conductance of single-molecule junctions. Our experiments on prototypical Au-alkanedithiol-Au junctions containing two to ten carbon atoms confirm that thermal conductance is to a first approximation independent of molecular length, consistent with detailed ab initio simulations. We anticipate that our approach will enable systematic exploration of thermal transport in many other one-dimensional systems, such as short molecules and polymer chains, for which computational predictions of thermal conductance13-16 have remained experimentally inaccessible.
- 8 June 2018
- Published by Springer Nature in BioChip Journal
- Vol. 12 (3) , 240-248
Rapid Determination of Ethyl Alcohol in Alcoholic Beverages Using a Fluorescent Nanofiber Film
- 8 June 2018
- Published by Springer Nature in BioChip Journal
- Vol. 12 (3) , 240-248
Rapid Determination of Ethyl Alcohol in Alcoholic Beverages Using a Fluorescent Nanofiber Film
- 1 February 2018
- Published by Elsevier in Nano Energy
- Vol. 44, 191-198
High-performance dopant-free conjugated small molecule-based hole-transport materials for perovskite solar cells
- 1 February 2018
- Published by Elsevier in Nano Energy
- Vol. 44, 191-198
High-performance dopant-free conjugated small molecule-based hole-transport materials for perovskite solar cells
- 1 January 2016
- Published by American Scientific Publishers in Science of Advanced Materials
- Vol. 8 (1) , 57-63
Fabrication of Porous Carbon Films and Their Applications for Electrocatalytic Electrodes
Porous polyacrylonitrile (PAN) films spin coated on a quartz substrate with subsequent drying under humid conditions were used for preparing porous carbon films (PCFs) through conventional heat treatments such as stabilization and carbonization. The drying time, relative humidity (RH), and concentration of the PAN solution affected the morphology of the porous surface without significantly changing the intrinsic properties of the carbon films as thick as ∼1.5 μm. The pores were present even after the heat treatments, and the resulting carbonized PAN films had pores with an average diameter and depth of up to ∼1.2 μm and ∼200 nm, respectively. The resulting PCFs were used as FTO-free counter electrodes (CEs) in dye-sensitized solar cells (DSSCs). The PCF-CEs displayed high electrical conductivity with a sheet resistance of ∼12 Ω/sq. Furthermore, PCFs showed superior charge transfer properties at CE/electrolyte interfaces and increased current exchange for electrochemical iodine reduction. The DSSCs using PCF-CEs dried for 120 min showed significantly improved power conversion efficiency (PCE, 5.24%) and fill factor (FF, 0.48) compared to those using carbon nanosheet CEs (PCE, 4.46%; FF, 0.4), because of the advantageous and synergistic electrical and morphological improvements. This work provides a promising class of potential materials that can be used as electrocatalytic electrodes in electrochemical devices.
- 1 January 2016
- Published by American Scientific Publishers in Science of Advanced Materials
- Vol. 8 (1) , 57-63
Fabrication of Porous Carbon Films and Their Applications for Electrocatalytic Electrodes
Porous polyacrylonitrile (PAN) films spin coated on a quartz substrate with subsequent drying under humid conditions were used for preparing porous carbon films (PCFs) through conventional heat treatments such as stabilization and carbonization. The drying time, relative humidity (RH), and concentration of the PAN solution affected the morphology of the porous surface without significantly changing the intrinsic properties of the carbon films as thick as ∼1.5 μm. The pores were present even after the heat treatments, and the resulting carbonized PAN films had pores with an average diameter and depth of up to ∼1.2 μm and ∼200 nm, respectively. The resulting PCFs were used as FTO-free counter electrodes (CEs) in dye-sensitized solar cells (DSSCs). The PCF-CEs displayed high electrical conductivity with a sheet resistance of ∼12 Ω/sq. Furthermore, PCFs showed superior charge transfer properties at CE/electrolyte interfaces and increased current exchange for electrochemical iodine reduction. The DSSCs using PCF-CEs dried for 120 min showed significantly improved power conversion efficiency (PCE, 5.24%) and fill factor (FF, 0.48) compared to those using carbon nanosheet CEs (PCE, 4.46%; FF, 0.4), because of the advantageous and synergistic electrical and morphological improvements. This work provides a promising class of potential materials that can be used as electrocatalytic electrodes in electrochemical devices.
- Open Access
- 8 September 2015
- Published by Optica Publishing Group in Optics Express
- Vol. 23 (19) , A1280-A1287
Improved performance of dye-sensitized solar cells using dual-function TiO_2 nanowire photoelectrode
A unique, hierarchically structured, aggregated TiO2 nanowire (A-TiO2-nw) is prepared by solvothermal synthesis and used as a dual-functioning photoelectrode in dye-sensitized solar cells (DSSCs). The A-TiO2-nw shows improved light scattering compared to conventional TiO2 nanoparticles (TiO2-np) and dramatically enhanced dye adsorption compared to conventional scattering particles (CSP). The A-TiO2-nw is used as a scattering layer for bilayer photoelectrodes (TiO2-np/A-TiO2-nw) in DSSCs to compare the cell performance to that of devices using state-of-the-art photoelectrode architectures (TiO2-np/CSP). The DSSCs fabricated using bilayers of TiO2-np/A-TiO2-nw show improved power conversion efficiency (9.1%) and current density (14.88 mA cm−2) compared to those using single-layer TiO2-np (7.6% and 11.84 mA cm−2) or TiO2-np/CSP bilayer structures (8.7% and 13.81 mA cm−2). The unique contribution of the A-TiO2-nw layers to the device performance is confirmed by studying the incident photon-to-current efficiency. The enhanced external quantum efficiencies at approximately 520 nm and 650 nm clearly reveal the dual functionality of A-TiO2-nw. These unique properties of A-TiO2-nw may be applied in other devices utilizing light-scattering n-type semiconductor.
- 8 September 2015
- Published by Optica Publishing Group in Optics Express
- Vol. 23 (19) , A1280-A1287
Open AccessImproved performance of dye-sensitized solar cells using dual-function TiO_2 nanowire photoelectrode
A unique, hierarchically structured, aggregated TiO2 nanowire (A-TiO2-nw) is prepared by solvothermal synthesis and used as a dual-functioning photoelectrode in dye-sensitized solar cells (DSSCs). The A-TiO2-nw shows improved light scattering compared to conventional TiO2 nanoparticles (TiO2-np) and dramatically enhanced dye adsorption compared to conventional scattering particles (CSP). The A-TiO2-nw is used as a scattering layer for bilayer photoelectrodes (TiO2-np/A-TiO2-nw) in DSSCs to compare the cell performance to that of devices using state-of-the-art photoelectrode architectures (TiO2-np/CSP). The DSSCs fabricated using bilayers of TiO2-np/A-TiO2-nw show improved power conversion efficiency (9.1%) and current density (14.88 mA cm−2) compared to those using single-layer TiO2-np (7.6% and 11.84 mA cm−2) or TiO2-np/CSP bilayer structures (8.7% and 13.81 mA cm−2). The unique contribution of the A-TiO2-nw layers to the device performance is confirmed by studying the incident photon-to-current efficiency. The enhanced external quantum efficiencies at approximately 520 nm and 650 nm clearly reveal the dual functionality of A-TiO2-nw. These unique properties of A-TiO2-nw may be applied in other devices utilizing light-scattering n-type semiconductor.
- 9 January 2015
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 119 (5) , 2314-2321
High-Efficiency FTO-Free Counter Electrodes for Dye-Sensitized Solar Cells Based on Low-Pt-Doped Carbon Nanosheets
- 9 January 2015
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 119 (5) , 2314-2321
High-Efficiency FTO-Free Counter Electrodes for Dye-Sensitized Solar Cells Based on Low-Pt-Doped Carbon Nanosheets
- 25 June 2014
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 16 (33) , 17595-17602
FTO-free counter electrodes for dye-sensitized solar cells using carbon nanosheets synthesised from a polymeric carbon source
Highly conductive carbon nanosheets (CNSs) are fabricated using a polymeric carbon source and subsequently applied as the counter electrodes (CNS-CEs) for dye-sensitized solar cells (DSSCs). The CNSs have a similar structure to multilayered graphene, and their high electrical conductivity and electrocatalytic activity enable them to have a dual-function as both CEs and charge supporting electrodes. CNSs form a unique CE material that functions successfully while being metal- and fluorine doped tin oxide (FTO)-free and allowing DSSCs to achieve ∼5% power conversion efficiency. The chemical structure, electrical properties, electrocatalytic activity, and work function of the CNS-CEs prepared under various conditions of carbonization are investigated, and their effects on the performance of the corresponding DSSCs are discussed. Carbonization temperature is shown to have influenced the size of graphitic domains and the presence of heteroatoms and functional groups in CNS-CEs. The change in the graphitic domain size has a marginal influence on the work function of the CNS-CEs and the overpotential for the reduction of the redox couples (I−/I3 −). However, the electrical conductivity of CNS-CEs and the charge transfer resistance at CE/electrolyte interfaces in the DSSCs are considerably influenced by the carbonization condition. Our study shows that CNSs serve as efficient, FTO-free CE materials for DSSCs, and they are appropriate materials with which the effects of the chemical/physical properties of graphene-based materials on the electrode performance of various electrochemical devices may be studied.
- 25 June 2014
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 16 (33) , 17595-17602
FTO-free counter electrodes for dye-sensitized solar cells using carbon nanosheets synthesised from a polymeric carbon source
Highly conductive carbon nanosheets (CNSs) are fabricated using a polymeric carbon source and subsequently applied as the counter electrodes (CNS-CEs) for dye-sensitized solar cells (DSSCs). The CNSs have a similar structure to multilayered graphene, and their high electrical conductivity and electrocatalytic activity enable them to have a dual-function as both CEs and charge supporting electrodes. CNSs form a unique CE material that functions successfully while being metal- and fluorine doped tin oxide (FTO)-free and allowing DSSCs to achieve ∼5% power conversion efficiency. The chemical structure, electrical properties, electrocatalytic activity, and work function of the CNS-CEs prepared under various conditions of carbonization are investigated, and their effects on the performance of the corresponding DSSCs are discussed. Carbonization temperature is shown to have influenced the size of graphitic domains and the presence of heteroatoms and functional groups in CNS-CEs. The change in the graphitic domain size has a marginal influence on the work function of the CNS-CEs and the overpotential for the reduction of the redox couples (I−/I3 −). However, the electrical conductivity of CNS-CEs and the charge transfer resistance at CE/electrolyte interfaces in the DSSCs are considerably influenced by the carbonization condition. Our study shows that CNSs serve as efficient, FTO-free CE materials for DSSCs, and they are appropriate materials with which the effects of the chemical/physical properties of graphene-based materials on the electrode performance of various electrochemical devices may be studied.
- 8 February 2013
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 5 (6) , 2053-2061
Aqueous Dispersible Graphene/Pt Nanohybrids by Green Chemistry: Application as Cathodes for Dye-Sensitized Solar Cells
Aqueous dispersible nanohybrids (NHBs) of graphene nanosheets (GNSs) and Pt nanoparticles (Pt-NPs) were synthesized through the one-pot reduction of their precursors using an environmentally benign chemical, vitamin C. The concurrent reduction of the precursors, which includes graphene oxide (GO) to GNS and H2PtCl6 to Pt0, was facile and efficient to yield GNS/Pt-NHBs in which face-centered cubic (fcc) crystalline Pt-NPs with average diameters of ∼5 nm were robustly attached on the surface of the GNSs. The conversion yield during Pt reduction was fairly high (∼90%) and the Pt content within the NHBs was easily controllable. The resulting stable aqueous colloidal dispersion of GNS/Pt-NHBs was successfully fabricated as thin films without using any binder by the electro-spray method at room temperature, and the fabricated samples were used as counter electrodes (CEs) for dye-sensitized solar cells (DSSCs). The electrocatalytic activity of the NHBs for I–/I3– redox couples in conventional DSSCs was investigated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) analysis. Doping of GNSs with small amounts of Pt-NPs (VOC: 830 mV, JSC: 15.56 mAcm–2, and FF: 69%), which is comparable to that of devices using the state-of-the-art Pt-based CEs (8.85%).
- 8 February 2013
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 5 (6) , 2053-2061
Aqueous Dispersible Graphene/Pt Nanohybrids by Green Chemistry: Application as Cathodes for Dye-Sensitized Solar Cells
Aqueous dispersible nanohybrids (NHBs) of graphene nanosheets (GNSs) and Pt nanoparticles (Pt-NPs) were synthesized through the one-pot reduction of their precursors using an environmentally benign chemical, vitamin C. The concurrent reduction of the precursors, which includes graphene oxide (GO) to GNS and H2PtCl6 to Pt0, was facile and efficient to yield GNS/Pt-NHBs in which face-centered cubic (fcc) crystalline Pt-NPs with average diameters of ∼5 nm were robustly attached on the surface of the GNSs. The conversion yield during Pt reduction was fairly high (∼90%) and the Pt content within the NHBs was easily controllable. The resulting stable aqueous colloidal dispersion of GNS/Pt-NHBs was successfully fabricated as thin films without using any binder by the electro-spray method at room temperature, and the fabricated samples were used as counter electrodes (CEs) for dye-sensitized solar cells (DSSCs). The electrocatalytic activity of the NHBs for I–/I3– redox couples in conventional DSSCs was investigated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) analysis. Doping of GNSs with small amounts of Pt-NPs (VOC: 830 mV, JSC: 15.56 mAcm–2, and FF: 69%), which is comparable to that of devices using the state-of-the-art Pt-based CEs (8.85%).
- 1 January 2010
- Published by AIP Publishing in AIP Conference Proceedings
- p. 148-153
Formation of Tio[sub 2] Thin Film for Dye-Sensitized Solar Cell Application Using Electrophoresis Deposition
One of important processes on the fabrication of dye‐sensitized solar cell (DSSC) is formation of thin film. Thickness of thin film is needed to be controlled in order to obtain optimum thickness. Electrophoresis deposition is simple method for thin film deposition which enable us to control the thickness of thin film. In this work, the formation of thin film on indium‐doped tin oxide (ITO) glass using electrophoresis deposition is numerically and experimentally studied. We have succeeded to control the thickness of thin film by changing of electrophoresis applied voltage and deposition time. In the experiment, particles were suspended into isopropyl alcohol solution. was added to the solution in order to obtain the stable solution for electrophoresis. We found numerically that the in the range from to is appropriate condition for the electrophoresis deposition. Using this method, we have fabricated DSSC device and study the effect of thickness on DSSCs characteristic. Our results shows that the electrophoresis is not only essential for DSSC application but also for the other devices with a given thickness of film.- 1 January 2010
- Published by AIP Publishing in AIP Conference Proceedings
- p. 148-153
Formation of Tio[sub 2] Thin Film for Dye-Sensitized Solar Cell Application Using Electrophoresis Deposition
One of important processes on the fabrication of dye‐sensitized solar cell (DSSC) is formation of thin film. Thickness of thin film is needed to be controlled in order to obtain optimum thickness. Electrophoresis deposition is simple method for thin film deposition which enable us to control the thickness of thin film. In this work, the formation of thin film on indium‐doped tin oxide (ITO) glass using electrophoresis deposition is numerically and experimentally studied. We have succeeded to control the thickness of thin film by changing of electrophoresis applied voltage and deposition time. In the experiment, particles were suspended into isopropyl alcohol solution. was added to the solution in order to obtain the stable solution for electrophoresis. We found numerically that the in the range from to is appropriate condition for the electrophoresis deposition. Using this method, we have fabricated DSSC device and study the effect of thickness on DSSCs characteristic. Our results shows that the electrophoresis is not only essential for DSSC application but also for the other devices with a given thickness of film.