Jingchang Ye
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jingchang Ye has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Ping Li
Shanghai Jiao Tong University
3 shared publications - Yumei Wen
Shanghai Jiao Tong University
3 shared publications - Huaxia Deng
University of Science and Technology of China
1 shared publication Jin Zhang
School of Instrument Science and Opto-electronics Engineering, Hefei University of Technology, Hefei, Anhui, 230009, People’s Republic of China
1 shared publicationMengchao Ma
School of Instrument Science and Opto-electronics Engineering, Hefei University of Technology, Hefei, Anhui, 230009, People’s Republic of China
1 shared publicationXiang Zhong
School of Instrument Science and Opto-electronics Engineering, Hefei University of Technology, Hefei, Anhui, 230009, People’s Republic of China
1 shared publication
Latest Publications
- 12 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
A “Self-Sufficient” In Situ Marine Electric Field Observing System
In-situ marine electric field sensing is an effective means of exploration for marine geological activities. Dynamic modulation measurement is commonly used in measurement solutions due to stability requirements in in-situ measurements. However, the high energy requirements of modulation measurement is a challenge underwater field. In this paper, we realise passive modulation measurements by utilising the low permittivity of bubbles. Further, we also utilise the energy of the bubbles to power the measurements, so to realise a self-powered in-situ electric field measurement system. Experiments show that the limit of detection (LOD) of the proposed passive bubble-modulated polarization method is 0.1 mV/m and the drift (1.42 × 10−4 (V/m)/day) is 1.2% of that of the conventional static measurement methods (1.1 × 10−2 (V/m)/day). The energy consumption of the proposed passive modulated measurement system (0.825 mW) is 2.75×10−5 of the conventional modulated measurement system (30 W). This paper truly realizes an in-situ long-term detection system that integrates energy supply and measurement, which can promote the exploitation of cold springs and hydrothermal fluids and the construction of the Internet of Underwater Things in these regions.
- 12 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
A “Self-Sufficient” In Situ Marine Electric Field Observing System
In-situ marine electric field sensing is an effective means of exploration for marine geological activities. Dynamic modulation measurement is commonly used in measurement solutions due to stability requirements in in-situ measurements. However, the high energy requirements of modulation measurement is a challenge underwater field. In this paper, we realise passive modulation measurements by utilising the low permittivity of bubbles. Further, we also utilise the energy of the bubbles to power the measurements, so to realise a self-powered in-situ electric field measurement system. Experiments show that the limit of detection (LOD) of the proposed passive bubble-modulated polarization method is 0.1 mV/m and the drift (1.42 × 10−4 (V/m)/day) is 1.2% of that of the conventional static measurement methods (1.1 × 10−2 (V/m)/day). The energy consumption of the proposed passive modulated measurement system (0.825 mW) is 2.75×10−5 of the conventional modulated measurement system (30 W). This paper truly realizes an in-situ long-term detection system that integrates energy supply and measurement, which can promote the exploitation of cold springs and hydrothermal fluids and the construction of the Internet of Underwater Things in these regions.
- 26 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-8
Polarization for Weak Marine Electric Field Measurement: A New Approach
Detection of weak marine electric fields is an issue of notable interest in the fields of marine biological research, monitoring of marine geological activity, and marine mineral exploration. The only way to increase sensitivity of the commonly applied self-potential (SP) method is to increase the spacing of the electrodes; however, this will also increase electrode and cable noise at the same time. This paper presents the application of a dielectric polarization technique to the measurement of marine electric fields for the first time; this can achieve high-sensitivity measurements with a small electrode spacing. Under the same conditions, the sensitivity of the proposed method(3.04 V(V/m)) is 6.2 times that of SP(0.49 V(V/m)); furthermore, its the signal-to-noise ratio(44.39 dB) is 27.47 dB higher than that of SP(16.92 dB), and its limit of detection(7 μV/m) is very notably lower than that of the SP method(260 μV/m). The proposed scheme is therefore not only capable of detecting weak marine electric fields, but it is also developing sensor arrays; this has the potential to lead to a new observation angle for marine electric field detection.
- 26 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-8
Polarization for Weak Marine Electric Field Measurement: A New Approach
Detection of weak marine electric fields is an issue of notable interest in the fields of marine biological research, monitoring of marine geological activity, and marine mineral exploration. The only way to increase sensitivity of the commonly applied self-potential (SP) method is to increase the spacing of the electrodes; however, this will also increase electrode and cable noise at the same time. This paper presents the application of a dielectric polarization technique to the measurement of marine electric fields for the first time; this can achieve high-sensitivity measurements with a small electrode spacing. Under the same conditions, the sensitivity of the proposed method(3.04 V(V/m)) is 6.2 times that of SP(0.49 V(V/m)); furthermore, its the signal-to-noise ratio(44.39 dB) is 27.47 dB higher than that of SP(16.92 dB), and its limit of detection(7 μV/m) is very notably lower than that of the SP method(260 μV/m). The proposed scheme is therefore not only capable of detecting weak marine electric fields, but it is also developing sensor arrays; this has the potential to lead to a new observation angle for marine electric field detection.
- 13 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (10) , 7841-7848
Marine Electric Field Observations With Variable Dielectric Polarization
Stability of marine electric fields measurements is a problem of broad interest in relation to long-term in-situ observations, especially in the construction of the Internet of Underwater Things(IoUT), geological exploration, and disaster monitoring. The root of this problem is the drift in electrode potential caused by imbalances in the electrodes’ electrical processes, which are unavoidable in potential-difference measurements based on the conduction current. Here, we propose the variable-dielectric polarization (VDP) measurement method, which uses the variation of a dielectric between the electrodes to measure the external electric field. This method modulates the electric-field signal to higher frequencies, allowing separation of the signal from the output by demodulation. This not only separates the signal from low-frequency noise, but it also increases the measurement sensitivity by frequency boosting. The results of our experiments show that the VDP system we constructed has a measurement sensitivity of 2.63 V/(V/m) and a measurement resolution of 22.4 μV/m. Under long-term measurements, the measured drift of the VDP system (106 (μV/m)/day) was found to be only 1/320 of the self-potential(SP) method(34 (mV/m)/day). The proposed VDP method thus provides a new approach to the construction of future IoUT devices and the prediction of marine disasters.
- 13 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (10) , 7841-7848
Marine Electric Field Observations With Variable Dielectric Polarization
Stability of marine electric fields measurements is a problem of broad interest in relation to long-term in-situ observations, especially in the construction of the Internet of Underwater Things(IoUT), geological exploration, and disaster monitoring. The root of this problem is the drift in electrode potential caused by imbalances in the electrodes’ electrical processes, which are unavoidable in potential-difference measurements based on the conduction current. Here, we propose the variable-dielectric polarization (VDP) measurement method, which uses the variation of a dielectric between the electrodes to measure the external electric field. This method modulates the electric-field signal to higher frequencies, allowing separation of the signal from the output by demodulation. This not only separates the signal from low-frequency noise, but it also increases the measurement sensitivity by frequency boosting. The results of our experiments show that the VDP system we constructed has a measurement sensitivity of 2.63 V/(V/m) and a measurement resolution of 22.4 μV/m. Under long-term measurements, the measured drift of the VDP system (106 (μV/m)/day) was found to be only 1/320 of the self-potential(SP) method(34 (mV/m)/day). The proposed VDP method thus provides a new approach to the construction of future IoUT devices and the prediction of marine disasters.
- Open Access
- 26 February 2019
- Published by Springer Nature in Communications Physics
- Vol. 2 (1) , 21
Poly-stable energy harvesting based on synergetic multistable vibration
Distributed energy sources, for example the ambient broadband vibrations, are of great importance for the development of the Internet of Things. However, for multistable vibrational energy harvesters, increasing the number of stable equilibrium states to broaden working frequency bands is very difficult. Here we present a poly-stable vibrational energy harvesting approach capable of achieving an exponentially growing maximum number of stable equilibrium states. Unlike the traditional multistable harvesters relying on an external static magnetic field, the nonlinear dynamical behaviours achieved by the proposed approach are synergetic poly-stable motions without the need of external magnets. Comparison experiments in contrast with a linear harvester demonstrate the working bandwidth widened by a factor of 41.0, the power density increased to 760% and the electricity generation raised to 178%. This demonstration of new multistable energy harvester expands the approach to achieving multistable motion and provides a new design philosophy for nonlinear vibrational energy harvesters.
- 26 February 2019
- Published by Springer Nature in Communications Physics
- Vol. 2 (1) , 21
Open AccessPoly-stable energy harvesting based on synergetic multistable vibration
Distributed energy sources, for example the ambient broadband vibrations, are of great importance for the development of the Internet of Things. However, for multistable vibrational energy harvesters, increasing the number of stable equilibrium states to broaden working frequency bands is very difficult. Here we present a poly-stable vibrational energy harvesting approach capable of achieving an exponentially growing maximum number of stable equilibrium states. Unlike the traditional multistable harvesters relying on an external static magnetic field, the nonlinear dynamical behaviours achieved by the proposed approach are synergetic poly-stable motions without the need of external magnets. Comparison experiments in contrast with a linear harvester demonstrate the working bandwidth widened by a factor of 41.0, the power density increased to 760% and the electricity generation raised to 178%. This demonstration of new multistable energy harvester expands the approach to achieving multistable motion and provides a new design philosophy for nonlinear vibrational energy harvesters.