Chiyen Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Chiyen Kim has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Alejandro Cuaron
W. M. Keck Center for 3D Innovation, The University of Texas at El Paso, El Paso, TX, USA
2 shared publications- Eric MacDonald
Aerospace and Mechanical Engineering, University of Texas at El Paso, El Paso, TX 79968, USA
2 shared publications Alexander Hillstrom
The Pennsylvania State University, University Park, USA
1 shared publicationCharlie Sullivan
The University of Texas at El Paso, El Paso, USA
1 shared publicationDavid Espalin
W.M. Keck Center for 3D Innovation, The University of Texas at El Paso, El Paso, TX, USA
1 shared publication- David Espalin
Department of Aerospace and Mechanical Engineering, The University of Texas at El Paso, 500 W. University Ave, El Paso, TX 79968, USA
1 shared publication
Latest Publications
- 12 April 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (5) , 919-931
Intermittent Embedding of Wire into 3D Prints for Wireless Power Transfer
- 12 April 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (5) , 919-931
Intermittent Embedding of Wire into 3D Prints for Wireless Power Transfer
- Open Access
- 31 August 2020
- Published by The Korean Society of Manufacturing Process Engineers in Journal of the Korean Society of Manufacturing Process Engineers
- Vol. 19 (8) , 73-80
Effect of 3D Printed Spiral Antenna Design on Inductive Coupling Wireless Power Transmission System
- 31 August 2020
- Published by The Korean Society of Manufacturing Process Engineers in Journal of the Korean Society of Manufacturing Process Engineers
- Vol. 19 (8) , 73-80
Open AccessEffect of 3D Printed Spiral Antenna Design on Inductive Coupling Wireless Power Transmission System
- 18 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 8 (8) , 1469-1476
Unobtrusive In Situ Diagnostics of Filament-Fed Material Extrusion Additive Manufacturing
Build defects, such as nozzle clogging and thermal substrate deformation, are common in material extrusion additive manufacturing technologies, and are difficult to detect because of the high-temperature environment of fused deposition modeling (FDM) machines that do not accommodate internal sensors. To overcome this difficulty, this paper integrated an external sensor to monitor the supply current of the motor that fed filament into an extrusion head. This paper describes the investigation of the relationship between the deposition status and the reaction torque on the filament-feed motor. A dynamic model of the internal operation of the FDM extrusion head was developed and used to infer printing defects. The change in reaction force opposing extrusion was indirectly measured by monitoring the current delivered to the filament-feed motor, and consequently, the use of other sensors in the high-temperature chamber was avoided. An analysis of the supply current, in both time and frequency domains, enabled the detection of defects during material deposition.
- 18 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 8 (8) , 1469-1476
Unobtrusive In Situ Diagnostics of Filament-Fed Material Extrusion Additive Manufacturing
Build defects, such as nozzle clogging and thermal substrate deformation, are common in material extrusion additive manufacturing technologies, and are difficult to detect because of the high-temperature environment of fused deposition modeling (FDM) machines that do not accommodate internal sensors. To overcome this difficulty, this paper integrated an external sensor to monitor the supply current of the motor that fed filament into an extrusion head. This paper describes the investigation of the relationship between the deposition status and the reaction torque on the filament-feed motor. A dynamic model of the internal operation of the FDM extrusion head was developed and used to infer printing defects. The change in reaction force opposing extrusion was indirectly measured by monitoring the current delivered to the filament-feed motor, and consequently, the use of other sensors in the high-temperature chamber was avoided. An analysis of the supply current, in both time and frequency domains, enabled the detection of defects during material deposition.
- Open Access
- 14 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 5, 25286-25294
3D Printed Electronics With High Performance, Multi-Layered Electrical Interconnect
2-D printed electronics have been the focus of intense research for the past two decades primarily focused on implementing electrical interconnect by dispensing conductive binder-based inks. More recently, traditional printed electronics processes have been leveraged within 3-D printed structures where components and interconnect are introduced during fabrication interruptions. The dielectric performance of 3-D printed materials compares well with traditional printed circuit board (PCB) dielectrics but one remaining challenge is the low conductivity of printed ink traces. The performance degradation is due to curing temperature limits imposed by the properties of the polymer substrates. Thermoplastics, such as ULTEM, can maintain form at over 200 °C, but production ink curing processes require 850 °C to provide an appropriate conductivity. Previous reports have described submerging wires with selective energy within a thermoplastic substrate upon which 3-D printing can continue uninhibited. As copper wires have the same conductivity as PCBs and can be implemented in a wide range of cross-sectional areas, 3-D printed electronics are now in a position to transform the electronics industry. This paper describes an inter-layer process to insert metal connection between layers-allowing for improved routing density and leveraging the geometries brought to bear by 3-D printing. Minimum placement distance between these 3-D printed vias was initially 1.5 mm, and the vias can connect layers separated by as much as 2.8 mm in the vertical build direction (z-axis). As the number of wires layers that can be fabricated is not as limited as traditional board lamination, complex routing can be realized within mass customized, arbitrary shapes.
- 14 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 5, 25286-25294
Open Access3D Printed Electronics With High Performance, Multi-Layered Electrical Interconnect
2-D printed electronics have been the focus of intense research for the past two decades primarily focused on implementing electrical interconnect by dispensing conductive binder-based inks. More recently, traditional printed electronics processes have been leveraged within 3-D printed structures where components and interconnect are introduced during fabrication interruptions. The dielectric performance of 3-D printed materials compares well with traditional printed circuit board (PCB) dielectrics but one remaining challenge is the low conductivity of printed ink traces. The performance degradation is due to curing temperature limits imposed by the properties of the polymer substrates. Thermoplastics, such as ULTEM, can maintain form at over 200 °C, but production ink curing processes require 850 °C to provide an appropriate conductivity. Previous reports have described submerging wires with selective energy within a thermoplastic substrate upon which 3-D printing can continue uninhibited. As copper wires have the same conductivity as PCBs and can be implemented in a wide range of cross-sectional areas, 3-D printed electronics are now in a position to transform the electronics industry. This paper describes an inter-layer process to insert metal connection between layers-allowing for improved routing density and leveraging the geometries brought to bear by 3-D printing. Minimum placement distance between these 3-D printed vias was initially 1.5 mm, and the vias can connect layers separated by as much as 2.8 mm in the vertical build direction (z-axis). As the number of wires layers that can be fabricated is not as limited as traditional board lamination, complex routing can be realized within mass customized, arbitrary shapes.