Ahmet Alper Öner
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ahmet Alper Öner has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
M. Salih Kirkgoz
3 shared publicationsMevlut Sami Akoz
3 shared publicationsM. Sami Akoz
2 shared publicationsMehmet Salih Kirkgoz
Department of Civil Engineering , University of Cukurova , 01330 , Adana , Turkey
2 shared publications- Mücella İlKentapar
Erciyes University, Kayseri, Turkey
2 shared publications - Serhat Akşit
ABDULLAH GÜL ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ
2 shared publications
Latest Publications
- 27 September 2025
- Published by Elsevier in Ocean Engineering
- Vol. 342
Effect of different pitch ratios on the flow around tandem circular cylinders with spoilers
- 27 September 2025
- Published by Elsevier in Ocean Engineering
- Vol. 342
Effect of different pitch ratios on the flow around tandem circular cylinders with spoilers
- 23 December 2024
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Computational and Experimental Investigation Of Water Surface Around Bridge Piers
Free surface flow around bridge piers is one of the most important problems of open channel hydraulics. The structural design of the bridge should be done correctly along with the hydraulic design by simulating the water surface around the bridge piers together with the scour that will occur around the bridge piers. If the hydraulic design of the bridge piers is not good enough, it can cause very serious damages in situations such as floods and overflows. The aim of this paper is to analyze the effect of bridge piers on the water surface experimentally and numerically. For the numerical analysis, FLOW-3D, a computational fluid dynamics package program that performs 3-dimensional solution, and HEC-RAS package program are used and the results are compared. In the study, flows with the same velocity for different number of bridge openings were studied and compared with the experimental results. In addition, the FLOW 3D package program, which performs solutions with the finite volume method, was compared with the experimental results by performing solutions with different mesh sizes. As a result, it was observed that the solutions performed with the FLOW-3D package program showed very close results with the experimental data.
- 23 December 2024
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Computational and Experimental Investigation Of Water Surface Around Bridge Piers
Free surface flow around bridge piers is one of the most important problems of open channel hydraulics. The structural design of the bridge should be done correctly along with the hydraulic design by simulating the water surface around the bridge piers together with the scour that will occur around the bridge piers. If the hydraulic design of the bridge piers is not good enough, it can cause very serious damages in situations such as floods and overflows. The aim of this paper is to analyze the effect of bridge piers on the water surface experimentally and numerically. For the numerical analysis, FLOW-3D, a computational fluid dynamics package program that performs 3-dimensional solution, and HEC-RAS package program are used and the results are compared. In the study, flows with the same velocity for different number of bridge openings were studied and compared with the experimental results. In addition, the FLOW 3D package program, which performs solutions with the finite volume method, was compared with the experimental results by performing solutions with different mesh sizes. As a result, it was observed that the solutions performed with the FLOW-3D package program showed very close results with the experimental data.
- Top Cited Papers
- 14 September 2022
- Published by Elsevier in Applied Soft Computing
- Vol. 129
Comparison of neural network, Gaussian regression, support vector machine, long short-term memory, multi-gene genetic programming, and M5 Trees methods for solving civil engineering problems
- 14 September 2022
- Published by Elsevier in Applied Soft Computing
- Vol. 129
Top Cited PapersComparison of neural network, Gaussian regression, support vector machine, long short-term memory, multi-gene genetic programming, and M5 Trees methods for solving civil engineering problems
- Open Access
- 15 July 2016
- Published by Omer Halisdemir Universitesi Muhendislik Bilimleri Dergisi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 5 (2) , 168-176
HAVUZLU BALIK GEÇİDİ HİDROLİĞİNİN DENEYSEL İNCELENMESİ
Tr en Bu çalışmada, ülkemizde ve dünyada en çok kullanılan balık geçitlerinin başında gelen havuzlu balık geçidi hidroliği deneysel olarak incelenmiştir. Deneyler açık kanal düzeneğinde gerçekleştirilmiştir. Kapaklar yerleştirilmek suretiyle oluşturulan beş ayrı havuzdaki hız alanı akustik dopler hız ölçüm cihazı ile ölçülmüştür. Orifisli perde duvarları, literatürde gölge balığı ya da üst alabalık kuşağı balıklarının geçmesi için tasarlanmış olanlara nispeten ½ oranında küçültülmüştür. Deneylerde kullanılan 6,2 L/s’lik debi için, birinci perde memba ve mansabı arasında 2 cm’lik bir yükseklik farkı olurken, bu fark diğer kapaklarda 1 cm olarak belirlenmiştir. Bu farklar 12,2 L/s’lik debi için ise 5,5 cm olarak ölçülmüştür. Havuzlardaki en büyük hızların orifislerin hemen mansabında olduğu belirlenmiştir. Ayrıca orifisler yakınındaki bu yüksek hız bölgelerinden uzaklaştıkça, balıkların geçerken dinlenebileceği daha düşük hızların oluştuğu akım alanları oluştuğu tespit edilmiştir. In this study, the pool and weir fishway which is the most commonly used fishway in the world and in our country, was investigated experimentally. The experiments were conducted in an open channel system. The velocity area of the flow in five pools created by using weirs was measured by using aquistic doppler velocimeter. The orifices on the weirs were reduced in the ratio of ½ that of given in the literature for the grayling (Thymallus thymallus) or the brown trout (Salmo trutta) to pass. In the experiments for a discharge value of Q=6.2 L/s, the difference between the height of the water surface of downward and upward side of the first weir was found to be 2 cm and 1 cm for the others. For Q=12.2 L/s, these differences between the water surface heights were 5.5 cm for all weirs. The maximum velocities were obtained next to downward of the orifices. Moreover, far from the high velocity areas near the orifices, lower velocity areas in the pools that fishes could rest during the passes were determined.
- 15 July 2016
- Published by Omer Halisdemir Universitesi Muhendislik Bilimleri Dergisi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 5 (2) , 168-176
Open AccessHAVUZLU BALIK GEÇİDİ HİDROLİĞİNİN DENEYSEL İNCELENMESİ
Tr en Bu çalışmada, ülkemizde ve dünyada en çok kullanılan balık geçitlerinin başında gelen havuzlu balık geçidi hidroliği deneysel olarak incelenmiştir. Deneyler açık kanal düzeneğinde gerçekleştirilmiştir. Kapaklar yerleştirilmek suretiyle oluşturulan beş ayrı havuzdaki hız alanı akustik dopler hız ölçüm cihazı ile ölçülmüştür. Orifisli perde duvarları, literatürde gölge balığı ya da üst alabalık kuşağı balıklarının geçmesi için tasarlanmış olanlara nispeten ½ oranında küçültülmüştür. Deneylerde kullanılan 6,2 L/s’lik debi için, birinci perde memba ve mansabı arasında 2 cm’lik bir yükseklik farkı olurken, bu fark diğer kapaklarda 1 cm olarak belirlenmiştir. Bu farklar 12,2 L/s’lik debi için ise 5,5 cm olarak ölçülmüştür. Havuzlardaki en büyük hızların orifislerin hemen mansabında olduğu belirlenmiştir. Ayrıca orifisler yakınındaki bu yüksek hız bölgelerinden uzaklaştıkça, balıkların geçerken dinlenebileceği daha düşük hızların oluştuğu akım alanları oluştuğu tespit edilmiştir. In this study, the pool and weir fishway which is the most commonly used fishway in the world and in our country, was investigated experimentally. The experiments were conducted in an open channel system. The velocity area of the flow in five pools created by using weirs was measured by using aquistic doppler velocimeter. The orifices on the weirs were reduced in the ratio of ½ that of given in the literature for the grayling (Thymallus thymallus) or the brown trout (Salmo trutta) to pass. In the experiments for a discharge value of Q=6.2 L/s, the difference between the height of the water surface of downward and upward side of the first weir was found to be 2 cm and 1 cm for the others. For Q=12.2 L/s, these differences between the water surface heights were 5.5 cm for all weirs. The maximum velocities were obtained next to downward of the orifices. Moreover, far from the high velocity areas near the orifices, lower velocity areas in the pools that fishes could rest during the passes were determined.
- Open Access
- 2 June 2016
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 8 (6)
Numerical investigation of flow around a pipeline with a spoiler near a rigid bed
Interaction of current with circular cylinders near a rigid bed is significant in the design of offshore structures, such as pipelines. Pipelines are buried to the seabed to be protected from damages caused by hydrodynamic forces or human activities. The pipeline laid on movable bed can be buried due to local scouring. A vertical plate on pipeline, called spoiler, has been developed to increase the rate and extend of scouring. In this study, the two-dimensional turbulent flow around a smooth pipeline with a spoiler was investigated at Re D = 9500 near the bed. The governing equations for the current problem were solved using ANSYS® 11.0-Flotran program package based on finite element method. The performance of the standard k–ε, standard k–ω, and shear stress transport turbulence models were examined on five computational meshes with different densities. The results obtained were compared with the published experimental measurements in literature. Present results showed that the attachment of a spoiler caused a large separation area in both upstream and downstream of the pipeline. The attachment of spoiler on top of the pipe increased the drag and decreased the lift force on pipe. Moreover, the spoiler causes non-zero downward lift. It is concluded that the k–ω turbulence model on the finest mesh is found relatively better in simulation of the flow field.
- 2 June 2016
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 8 (6)
Open AccessNumerical investigation of flow around a pipeline with a spoiler near a rigid bed
Interaction of current with circular cylinders near a rigid bed is significant in the design of offshore structures, such as pipelines. Pipelines are buried to the seabed to be protected from damages caused by hydrodynamic forces or human activities. The pipeline laid on movable bed can be buried due to local scouring. A vertical plate on pipeline, called spoiler, has been developed to increase the rate and extend of scouring. In this study, the two-dimensional turbulent flow around a smooth pipeline with a spoiler was investigated at Re D = 9500 near the bed. The governing equations for the current problem were solved using ANSYS® 11.0-Flotran program package based on finite element method. The performance of the standard k–ε, standard k–ω, and shear stress transport turbulence models were examined on five computational meshes with different densities. The results obtained were compared with the published experimental measurements in literature. Present results showed that the attachment of a spoiler caused a large separation area in both upstream and downstream of the pipeline. The attachment of spoiler on top of the pipe increased the drag and decreased the lift force on pipe. Moreover, the spoiler causes non-zero downward lift. It is concluded that the k–ω turbulence model on the finest mesh is found relatively better in simulation of the flow field.
- Open Access
- 1 January 2012
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 4
Experimental Validation of Volume of Fluid Method for a Sluice Gate Flow
Laboratory experiments are conducted for 2D turbulent free surface flow which interacts with a vertical sluice gate. The velocity field, on the centerline of the channel flow upstream of the gate is measured using the particle image velocimetry technique. The numerical simulation of the same flow is carried out by solving the governing equations, Reynolds-averaged continuity and Navier-Stokes equations, using finite element method. In the numerical solution of the governing equations, the standard turbulence closure model is used to define the turbulent viscosity. The measured horizontal velocity distribution at the inflow boundary of the solution domain is taken as the boundary condition. The volume of fluid (VOF) method is used to determine the flow profile in the channel. Taking into account of the flow characteristics, the computational domain is divided into five subdomains, each having different mesh densities. Three different meshes with five subdomains are employed for the numerical model. A grid convergence analysis indicates that the discretization error in the predicted velocities on the fine mesh remains within 2%. The computational results are compared with the experimental data, and, the most suitable mesh in predicting the velocity field and the flow profile among the three meshes is selected.- 1 January 2012
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 4
Open AccessExperimental Validation of Volume of Fluid Method for a Sluice Gate Flow
Laboratory experiments are conducted for 2D turbulent free surface flow which interacts with a vertical sluice gate. The velocity field, on the centerline of the channel flow upstream of the gate is measured using the particle image velocimetry technique. The numerical simulation of the same flow is carried out by solving the governing equations, Reynolds-averaged continuity and Navier-Stokes equations, using finite element method. In the numerical solution of the governing equations, the standard turbulence closure model is used to define the turbulent viscosity. The measured horizontal velocity distribution at the inflow boundary of the solution domain is taken as the boundary condition. The volume of fluid (VOF) method is used to determine the flow profile in the channel. Taking into account of the flow characteristics, the computational domain is divided into five subdomains, each having different mesh densities. Three different meshes with five subdomains are employed for the numerical model. A grid convergence analysis indicates that the discretization error in the predicted velocities on the fine mesh remains within 2%. The computational results are compared with the experimental data, and, the most suitable mesh in predicting the velocity field and the flow profile among the three meshes is selected. - 1 July 2011
- Published by Elsevier in Applied Ocean Research
- Vol. 33 (3) , 178-185
Prediction of geometrical properties of perfect breaking waves on composite breakwaters
- 1 July 2011
- Published by Elsevier in Applied Ocean Research
- Vol. 33 (3) , 178-185
Prediction of geometrical properties of perfect breaking waves on composite breakwaters
- 1 November 2009
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 47 (6) , 790-797
Numerical modeling of flow over a chute spillway
The simulation performance of two–dimensional flow over a round–crested chute spillway is examined using the finite element method along with the standard k–ε and the standard k–ω turbulence models. The volume of fluid method is used to determine the free surface of the flow.A mesh dependence study is conducted using the results obtained from three meshes of different densities. Grid convergence analyses indicate that the discretization error in the predicted velocities on the fine–mesh solution is within 2%. A two–layer model for the near–wall treatment was adopted involving a sufficiently fine mesh to model the viscosity–affected region. The numerical results are compared with experimental data for validation of turbulence models. Mean square errors of measured and predicted free surface and velocity profiles indicate that although both closure models predict the chute flow properties with a reasonable accuracy, the agreement using the k–ε model is slightly better.
- 1 November 2009
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 47 (6) , 790-797
Numerical modeling of flow over a chute spillway
The simulation performance of two–dimensional flow over a round–crested chute spillway is examined using the finite element method along with the standard k–ε and the standard k–ω turbulence models. The volume of fluid method is used to determine the free surface of the flow.A mesh dependence study is conducted using the results obtained from three meshes of different densities. Grid convergence analyses indicate that the discretization error in the predicted velocities on the fine–mesh solution is within 2%. A two–layer model for the near–wall treatment was adopted involving a sufficiently fine mesh to model the viscosity–affected region. The numerical results are compared with experimental data for validation of turbulence models. Mean square errors of measured and predicted free surface and velocity profiles indicate that although both closure models predict the chute flow properties with a reasonable accuracy, the agreement using the k–ε model is slightly better.
- 1 November 2009
- Published by Elsevier in Advances in Engineering Software
- Vol. 40 (11) , 1191-1199
Numerical modeling of interaction of a current with a circular cylinder near a rigid bed
- 1 November 2009
- Published by Elsevier in Advances in Engineering Software
- Vol. 40 (11) , 1191-1199
Numerical modeling of interaction of a current with a circular cylinder near a rigid bed
- 19 August 2009
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 224 (1) , 109-121
The flow around a pipeline with a spoiler
Offshore pipelines are buried in the seabed to be protected from the damage caused by hydrodynamic forces or by human activities. However, because of soil erosion and interaction of currents with the pipeline on the moveable seabed, the processes of local scouring and, sometimes, self-burial of pipelines take place. To increase the rate and extent of scouring, the technique of attaching a spoiler to the pipeline has been developed. In this study, two-dimensional, steady, turbulent flow around a horizontal pipeline with a spoiler near a smooth wall is investigated experimentally by using the particle image velocimetry technique. The effect of the spoiler was examined for the Reynolds numbers of ReD=840, 1500, 4150, and 9500 based on the pipe diameter. The effect of the spoiler on the process of scouring is investigated through the parameters of the measured instantaneous and time-averaged patterns of the velocity vector field and the streamline topology. The results indicated that the attachment of the spoiler to the pipeline increases the length of the upstream and downstream separation regions and it is also observed that the spoiler does not significantly increase the rate of the flow that passes through the gap and the shear stress acting on the seabed.
- 19 August 2009
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 224 (1) , 109-121
The flow around a pipeline with a spoiler
Offshore pipelines are buried in the seabed to be protected from the damage caused by hydrodynamic forces or by human activities. However, because of soil erosion and interaction of currents with the pipeline on the moveable seabed, the processes of local scouring and, sometimes, self-burial of pipelines take place. To increase the rate and extent of scouring, the technique of attaching a spoiler to the pipeline has been developed. In this study, two-dimensional, steady, turbulent flow around a horizontal pipeline with a spoiler near a smooth wall is investigated experimentally by using the particle image velocimetry technique. The effect of the spoiler was examined for the Reynolds numbers of ReD=840, 1500, 4150, and 9500 based on the pipe diameter. The effect of the spoiler on the process of scouring is investigated through the parameters of the measured instantaneous and time-averaged patterns of the velocity vector field and the streamline topology. The results indicated that the attachment of the spoiler to the pipeline increases the length of the upstream and downstream separation regions and it is also observed that the spoiler does not significantly increase the rate of the flow that passes through the gap and the shear stress acting on the seabed.