Zbigniew Stachura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Zbigniew Stachura has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Marian Giżejowski
Politechnika Warszawska Wydział Inżynierii Lądowej
6 shared publications - Marcin Gajewski
Road and Bridge Research Institute, 1 Instytutowa St., 03-302 Warsaw
5 shared publications - Marian Giżejowski
Warsaw Univ Technol, Fac Civil Engn, Al Armii Ludowej 16, PL-00637 Warsaw, Poland
5 shared publications M Gizejowski
4 shared publicationsMarian Giżejowski
Warsaw University of Technology
4 shared publicationsRadosław Szczerba
Warsaw University of Technology
4 shared publications
Latest Publications
- 28 February 2025
- Published by Index Copernicus in Inżynieria i Budownictwo
- Vol. LXXXI (1) , 28-35
Influence of material and geometric property statistics on the random buckling resistance of steel bisymmetric rolled double-tee section members under compression
The buckling resistance of steel elements in compression was evaluated in this paper. Members were made of bisymmetric double-tee rolled sections of narrow and wide flanges. The effects of residual stresses and geometric bow imperfections is not taken into account. The randomness of cross-section properties and mechanical properties of steel is taken into consideration. A number of Monte Carlo simulations of the random buckling resistance of steel elements in compression were performed taking into consideration the contemporary Polish and European statistical data. Conclusions and practical recommendations are presented with reference to PN-EN 1993-1-1:2006.
- 28 February 2025
- Published by Index Copernicus in Inżynieria i Budownictwo
- Vol. LXXXI (1) , 28-35
Influence of material and geometric property statistics on the random buckling resistance of steel bisymmetric rolled double-tee section members under compression
The buckling resistance of steel elements in compression was evaluated in this paper. Members were made of bisymmetric double-tee rolled sections of narrow and wide flanges. The effects of residual stresses and geometric bow imperfections is not taken into account. The randomness of cross-section properties and mechanical properties of steel is taken into consideration. A number of Monte Carlo simulations of the random buckling resistance of steel elements in compression were performed taking into consideration the contemporary Polish and European statistical data. Conclusions and practical recommendations are presented with reference to PN-EN 1993-1-1:2006.
- Open Access
- 31 March 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- Vol. 67 (1) , 635-656
Elastic Flexural-Torsional Buckling of Steel I-Section Members Unrestrained Between End Supports
Elastic instability of steel I-section members has been investigated with regard to axial compression, major axis bending as well as compression and major axis bending, based on the Vlasov theory of thin-walled members. Investigations presented in this paper deal with the energy method applied to the flexural-torsional buckling (FTB) problems of any complex loading case that for convenience of predictions is treated as a superposition of symmetric and antisymmetric components. Firstly, the review of energy equation formulations is presented for the elastic lateral-torsional buckling (LTB) of beams, then the most accurate beam energy equation, so-called the classical energy equation formulated for bisymmetric I-section beams is extended to cover also the beam-column out-of-plane stability problems, referred hereafter to FTB problems. Secondly, for the simple end boundary conditions, the shape functions of twist rotation and minor axis displacement are chosen such that they cover both symmetric and antisymmetric lateral-torsional buckling modes in relation to two lowest eigenvalues of the beam LTB in major axis bending. Finally, the explicit form of the general solution is presented being dependent upon the dimensionless bending moment equations for symmetric and antisymmetric components, and the load factor where the lower k index identifies the load case.
- 31 March 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- Vol. 67 (1) , 635-656
Open AccessElastic Flexural-Torsional Buckling of Steel I-Section Members Unrestrained Between End Supports
Elastic instability of steel I-section members has been investigated with regard to axial compression, major axis bending as well as compression and major axis bending, based on the Vlasov theory of thin-walled members. Investigations presented in this paper deal with the energy method applied to the flexural-torsional buckling (FTB) problems of any complex loading case that for convenience of predictions is treated as a superposition of symmetric and antisymmetric components. Firstly, the review of energy equation formulations is presented for the elastic lateral-torsional buckling (LTB) of beams, then the most accurate beam energy equation, so-called the classical energy equation formulated for bisymmetric I-section beams is extended to cover also the beam-column out-of-plane stability problems, referred hereafter to FTB problems. Secondly, for the simple end boundary conditions, the shape functions of twist rotation and minor axis displacement are chosen such that they cover both symmetric and antisymmetric lateral-torsional buckling modes in relation to two lowest eigenvalues of the beam LTB in major axis bending. Finally, the explicit form of the general solution is presented being dependent upon the dimensionless bending moment equations for symmetric and antisymmetric components, and the load factor where the lower k index identifies the load case.
- Open Access
- 31 March 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- p. 323-348
Buckling Resistance of Quasi-Straight H-Section Beam-Columns under Unequal End Moments
Steel prismatic elements of equal flanges double-tee section subject to major axis bending and compression, unrestrained in the out-of-plane direction between the supports, are vulnerable to buckling modes associated with minor axis flexural and torsional deformations. When end bending moments are acting alone on the quasi-straight member, the sensitivity to lateral-torsional buckling (LTB) is very much dependent upon the ratio of section minor axis to major axis moments of inertia, and additionally visibly dependent upon the major axis moment gradient ratio. In the case of major axis bending with the presence of a compressive axial force, even of rather small value in relation to the section squash resistance, there is a drastic reduction of structural elements in their realistic lengths to maintain a tendency to fail in the out-of-plane mode, governed by the large twist rotation. Increasing the load effects ratio of dimensionless axial force to dimensionless maximum major axis bending moment, the buckling mode goes away from that of lateral-torsional one, starting to become that closer to the minor axis flexural buckling (FBZ) mode. Different aspects of the flexural-torsional buckling (FTB) resistance of the typical rolled H-section beam-column with regard to the General Method (GM) formulation, developed by the authors elsewhere and based on the parametric finite element analysis, are dealt with in this paper. Investigations are concerned with different member slender ratio, different moment gradient ratios and different load effects ratio. Final conclusions are related to practical applications of the proposed format of General Method in relation to the effect of large displacements on the FTB resistance reduction factor described through the dimensionless measure of action effects and the FTB relative slenderness ratio of quasi-straight beam-columns.
- 31 March 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Civil Engineering
- p. 323-348
Open AccessBuckling Resistance of Quasi-Straight H-Section Beam-Columns under Unequal End Moments
Steel prismatic elements of equal flanges double-tee section subject to major axis bending and compression, unrestrained in the out-of-plane direction between the supports, are vulnerable to buckling modes associated with minor axis flexural and torsional deformations. When end bending moments are acting alone on the quasi-straight member, the sensitivity to lateral-torsional buckling (LTB) is very much dependent upon the ratio of section minor axis to major axis moments of inertia, and additionally visibly dependent upon the major axis moment gradient ratio. In the case of major axis bending with the presence of a compressive axial force, even of rather small value in relation to the section squash resistance, there is a drastic reduction of structural elements in their realistic lengths to maintain a tendency to fail in the out-of-plane mode, governed by the large twist rotation. Increasing the load effects ratio of dimensionless axial force to dimensionless maximum major axis bending moment, the buckling mode goes away from that of lateral-torsional one, starting to become that closer to the minor axis flexural buckling (FBZ) mode. Different aspects of the flexural-torsional buckling (FTB) resistance of the typical rolled H-section beam-column with regard to the General Method (GM) formulation, developed by the authors elsewhere and based on the parametric finite element analysis, are dealt with in this paper. Investigations are concerned with different member slender ratio, different moment gradient ratios and different load effects ratio. Final conclusions are related to practical applications of the proposed format of General Method in relation to the effect of large displacements on the FTB resistance reduction factor described through the dimensionless measure of action effects and the FTB relative slenderness ratio of quasi-straight beam-columns.
- 1 September 2019
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 160, 153-168
Out-of-plane buckling resistance of rolled steel H-section beam-columns under unequal end moments
- 1 September 2019
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 160, 153-168
Out-of-plane buckling resistance of rolled steel H-section beam-columns under unequal end moments
- 1 June 2019
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 157, 347-358
Buckling resistance of steel H-section beam–columns: In-plane buckling resistance
- 1 June 2019
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 157, 347-358
Buckling resistance of steel H-section beam–columns: In-plane buckling resistance
- Open Access
- 30 January 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 262, 09010
Buckling resistance evaluation of steel beam-columns using refined General Method approach
Different aspects of Eurocode 3 General Method (GM) approaches are discussed in this paper. The purpose of present study is to improve the application of GM approach for both beam-columns without intermediate lateral-torsional restraints and with these restraints. The results from the proposed GM are compared with those from Eurocode 3-1-1 interaction equations according to Method 1 and Method 2. A better consistency between the developed GM approach and the Eurocode's interaction equation approach than Eurocode 3 GM approach is observed.
- 30 January 2019
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 262, 09010
Open AccessBuckling resistance evaluation of steel beam-columns using refined General Method approach
Different aspects of Eurocode 3 General Method (GM) approaches are discussed in this paper. The purpose of present study is to improve the application of GM approach for both beam-columns without intermediate lateral-torsional restraints and with these restraints. The results from the proposed GM are compared with those from Eurocode 3-1-1 interaction equations according to Method 1 and Method 2. A better consistency between the developed GM approach and the Eurocode's interaction equation approach than Eurocode 3 GM approach is observed.
- Open Access
- 4 August 2018
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 19 (2) , 559-576
Buckling Resistance Criteria of Prismatic Beams Under Biaxial Moment Gradient
- 4 August 2018
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 19 (2) , 559-576
Open AccessBuckling Resistance Criteria of Prismatic Beams Under Biaxial Moment Gradient
- Open Access
- 1 June 2017
- Published by University of Zielona Góra, Poland in Civil and Environmental Engineering Reports
- Vol. 25 (2) , 89-105
A Consistent Ayrton-Perry Approach for the Flexural-Torsional Buckling Resistance Evaluation of Steel I-Section Members
Steel I-section members subjected to compression a monoaxial bending about the major axis are dealt with in this paper. The current Eurocode’s design procedure of such members is based on a set of two interpolation equations. In this paper a simple and yet consistent Ayrton-Perry methodology is presented that for beam-columns yields the Ayrton-Perry design strategy similar to that utilized in the steel Eurocodes for design of beams and columns but not used so far for the beam-column design. The results from developed design criterion are compared with those of Method 1 of Eurocode 3 and the Ayrton-Perry formulation of a different format that has been recently published.
- 1 June 2017
- Published by University of Zielona Góra, Poland in Civil and Environmental Engineering Reports
- Vol. 25 (2) , 89-105
Open AccessA Consistent Ayrton-Perry Approach for the Flexural-Torsional Buckling Resistance Evaluation of Steel I-Section Members
Steel I-section members subjected to compression a monoaxial bending about the major axis are dealt with in this paper. The current Eurocode’s design procedure of such members is based on a set of two interpolation equations. In this paper a simple and yet consistent Ayrton-Perry methodology is presented that for beam-columns yields the Ayrton-Perry design strategy similar to that utilized in the steel Eurocodes for design of beams and columns but not used so far for the beam-column design. The results from developed design criterion are compared with those of Method 1 of Eurocode 3 and the Ayrton-Perry formulation of a different format that has been recently published.
- 1 February 2017
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 17 (2) , 205-221
Buckling resistance assessment of steel I-section beam-columns not susceptible to LT-buckling
- 1 February 2017
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 17 (2) , 205-221
Buckling resistance assessment of steel I-section beam-columns not susceptible to LT-buckling