Haim Abramovich
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Haim Abramovich has a total of 102 co-authors. Here are the top co-authors by number of shared publications:
Yaakov Oshman
Technion—Israel Institute of Technology, 32000 Haifa, Israel
11 shared publicationsTanchum Weller
Faculty of Aerospace Engineering, Technion, IIT, Haifa, 32000, Israel
10 shared publicationsT. Weller
7 shared publications- Chiara Bisagni
Department of Aerospace Science and Technology, Politecnico di Milano, Via La Masa 34, 20156 Milano, Italy
5 shared publications - Lucy Edery-Azulay
Faculty of Aerospace Engineering, Technion – Israel Institute of Technology, 32000 Haifa, Israel
5 shared publications Scott Miller
Hughes Space & Communications Co., El Segundo, CA
5 shared publications
Latest Publications
- Open Access
Behavior of Defective Aluminum Panels Under Shear Forces Patched with Composite Plates—A New Engineering Approach
Old airplanes produced in the 1970s are still flying, while being exposed to various new types of detriments, leading to a need to repair them to enable the safe use of the airborne body. The present state of the art advocates the use of laminated composite to repair aluminum parts due to their effective durability. The studies presented in the literature mainly focused on bodies under tensile loads. It seems that shear-type loading appearing in the fuselage of airplanes when being under torsion has been ignored in literature. Therefore, to fill this gap, the present study investigates the behavior of defective aluminum panels under pure shear. The present investigation uses a novel finite element (FE) method of modelling the loaded body by 2D and 3D elements. Then, the model is used to calculate the influence of various parameters, like the size of the repair patch, overlaps, sequences of the laminated composite plate, and other structural properties on the stability and strength of the examined part. To validate the numerical predictions, tests were performed on typical elements. Based on the experimental results, the fidelity of the FE model was assessed and the method approach of repairing using composite patches was validated. The main conclusion from the present study is the use of solid (3D) elements, over shell (2D) elements, due to their high-fidelity results.
Open AccessBehavior of Defective Aluminum Panels Under Shear Forces Patched with Composite Plates—A New Engineering Approach
Old airplanes produced in the 1970s are still flying, while being exposed to various new types of detriments, leading to a need to repair them to enable the safe use of the airborne body. The present state of the art advocates the use of laminated composite to repair aluminum parts due to their effective durability. The studies presented in the literature mainly focused on bodies under tensile loads. It seems that shear-type loading appearing in the fuselage of airplanes when being under torsion has been ignored in literature. Therefore, to fill this gap, the present study investigates the behavior of defective aluminum panels under pure shear. The present investigation uses a novel finite element (FE) method of modelling the loaded body by 2D and 3D elements. Then, the model is used to calculate the influence of various parameters, like the size of the repair patch, overlaps, sequences of the laminated composite plate, and other structural properties on the stability and strength of the examined part. To validate the numerical predictions, tests were performed on typical elements. Based on the experimental results, the fidelity of the FE model was assessed and the method approach of repairing using composite patches was validated. The main conclusion from the present study is the use of solid (3D) elements, over shell (2D) elements, due to their high-fidelity results.
- Open Access
The Behavior of Long Thin Rectangular Plates under Normal Pressure—A Thorough Investigation
Thin rectangular plates are considered basic structures in various sectors like aerospace, civil, and mechanical engineering. Moreover, isotropic and laminated composite plates subjected to transverse normal loading and undergoing small and large deflections have been extensively studied and published in the literature. Yet, it seems that the particular case of long thin plates having a high aspect ratio appears to be almost ignored by various scholars despite its engineering importance. The present study tries to fill this gap, yielding novel findings regarding the structural behavior of long thin plates in the small- and large-deflection regimes. In contrast to what is normally assumed in the literature, namely that a long plate with a high aspect ratio can be considered an infinitely long plate, the present results clearly show that the structural effects of the ends continue to exist near the remote ends of the long plate. An innovative finding is that long plates would (only on movable boundary conditions for the large-deflection regime) exhibit a larger mid-width displacement in comparison with deflections of infinitely long plates. This innovative higher deflection appears for both small and large-deflection regimes for both all-around simply supported and all-around clamped boundary conditions. This new finding was shown to be valid for both isotropic and orthotropic materials and presents a novel engineering approach for the old assumption well quoted in the literature that a relatively long plate on any boundary condition can be considered an infinite plate. Based on the present research, it is recommended that this assumption should be used carefully as the largest plate mid-deflection might occur at finite aspect ratios.
Open AccessThe Behavior of Long Thin Rectangular Plates under Normal Pressure—A Thorough Investigation
Thin rectangular plates are considered basic structures in various sectors like aerospace, civil, and mechanical engineering. Moreover, isotropic and laminated composite plates subjected to transverse normal loading and undergoing small and large deflections have been extensively studied and published in the literature. Yet, it seems that the particular case of long thin plates having a high aspect ratio appears to be almost ignored by various scholars despite its engineering importance. The present study tries to fill this gap, yielding novel findings regarding the structural behavior of long thin plates in the small- and large-deflection regimes. In contrast to what is normally assumed in the literature, namely that a long plate with a high aspect ratio can be considered an infinitely long plate, the present results clearly show that the structural effects of the ends continue to exist near the remote ends of the long plate. An innovative finding is that long plates would (only on movable boundary conditions for the large-deflection regime) exhibit a larger mid-width displacement in comparison with deflections of infinitely long plates. This innovative higher deflection appears for both small and large-deflection regimes for both all-around simply supported and all-around clamped boundary conditions. This new finding was shown to be valid for both isotropic and orthotropic materials and presents a novel engineering approach for the old assumption well quoted in the literature that a relatively long plate on any boundary condition can be considered an infinite plate. Based on the present research, it is recommended that this assumption should be used carefully as the largest plate mid-deflection might occur at finite aspect ratios.
- Open Access
Innovative Insights on the Thin Square Plate Large Deflection Problem
Thin plates subjected to transverse load and undergoing large deflections have been widely studied and published in the literature. However, there is still a lack of information and understanding about the membrane stresses created under large deflections and their associated Airy stress function, as displayed in the well-known von Kármán equations set. The present study aims at providing explicit expressions for the membrane stresses, the deflections, and the Airy stress function for a general square plate area vertically uniformly loaded to reach large deflection state. This was obtained by using the results of a high-fidelity finite element analysis applied on a lateral loaded simply supported thin square plate, which are then casted to yield approximate Fourier series expressions for the membrane stresses, deflections, and the Airy stress function. The stress map figures provide a good understanding of the critical points on the plate, while the explicit mathematical expressions enabled the calculation of deflections and stresses for the entire plate area. Among other interesting findings, the presence of relatively high tensile and compressive membrane stresses existing near the plate edges was revealed, which might lead to potential failure hazards. The derivatives of the deflections and the Airy stress function enabled the validation of the large deflections von Kármán equations set for the investigated case, and it turned out that the generated expressions for the stresses and the lateral deflection based on a high-fidelity finite element model satisfy the second equation with a good accuracy, while the first one remains to further be investigated. Moreover, using the generated explicit equations, the load influence on the deflections and stresses was also analyzed to yield general novel expressions for the medium and very large deflections states. To generalize the investigated case, the stresses and the deflections were non-dimensionalized so they can be used for any material and plate dimensions.
Open AccessInnovative Insights on the Thin Square Plate Large Deflection Problem
Thin plates subjected to transverse load and undergoing large deflections have been widely studied and published in the literature. However, there is still a lack of information and understanding about the membrane stresses created under large deflections and their associated Airy stress function, as displayed in the well-known von Kármán equations set. The present study aims at providing explicit expressions for the membrane stresses, the deflections, and the Airy stress function for a general square plate area vertically uniformly loaded to reach large deflection state. This was obtained by using the results of a high-fidelity finite element analysis applied on a lateral loaded simply supported thin square plate, which are then casted to yield approximate Fourier series expressions for the membrane stresses, deflections, and the Airy stress function. The stress map figures provide a good understanding of the critical points on the plate, while the explicit mathematical expressions enabled the calculation of deflections and stresses for the entire plate area. Among other interesting findings, the presence of relatively high tensile and compressive membrane stresses existing near the plate edges was revealed, which might lead to potential failure hazards. The derivatives of the deflections and the Airy stress function enabled the validation of the large deflections von Kármán equations set for the investigated case, and it turned out that the generated expressions for the stresses and the lateral deflection based on a high-fidelity finite element model satisfy the second equation with a good accuracy, while the first one remains to further be investigated. Moreover, using the generated explicit equations, the load influence on the deflections and stresses was also analyzed to yield general novel expressions for the medium and very large deflections states. To generalize the investigated case, the stresses and the deflections were non-dimensionalized so they can be used for any material and plate dimensions.
- Open Access
Multiwall Rectangular Plates under Transverse Pressure—A Non-Linear Experimental and Numerical Study
Large deflection of rectangular plates under transverse pressure is described by Föppl–von Kármán equations, which have only approximated solutions. One of these methods is the separation into a small deflection plate and a thin membrane described by a simple third order polynomial expression. The present study presents an analysis to obtain analytical expressions for its coefficients by using the plate’s elastic properties and dimensions. To validate the non-linear relationship between the pressure and the lateral displacement of the multiwall plate, a vacuum chamber loading test is used to measure the plate’s response, with a large number of plates and length–width combinations. In addition, to further validate the analytical expressions, several finite element analyses (FEA) were performed. It has been found that the polynomial expression fairly describes the measured and calculated deflections. This method allows the prediction of plate deflections under pressure as soon as the elastic properties and the dimensions are known.
Open AccessMultiwall Rectangular Plates under Transverse Pressure—A Non-Linear Experimental and Numerical Study
Large deflection of rectangular plates under transverse pressure is described by Föppl–von Kármán equations, which have only approximated solutions. One of these methods is the separation into a small deflection plate and a thin membrane described by a simple third order polynomial expression. The present study presents an analysis to obtain analytical expressions for its coefficients by using the plate’s elastic properties and dimensions. To validate the non-linear relationship between the pressure and the lateral displacement of the multiwall plate, a vacuum chamber loading test is used to measure the plate’s response, with a large number of plates and length–width combinations. In addition, to further validate the analytical expressions, several finite element analyses (FEA) were performed. It has been found that the polynomial expression fairly describes the measured and calculated deflections. This method allows the prediction of plate deflections under pressure as soon as the elastic properties and the dimensions are known.
- Open Access
Large Deflections of Thin-Walled Plates under Transverse Loading—Investigation of the Generated In-Plane Stresses
Thin-walled plates subjected to transverse loading undergoing large deflection have been the topic of a large number of studies. However, there is still a lack of information about the nature and the distribution membrane stresses generated under large deflections. The purpose of this paper is to calculate and display the distribution of the generated stresses and the respective deflections on the entire rectangular plate area. Finite element analysis results for thin-walled plates with aspect ratios of 1, 2 and 5, on movable and immovable edges simply supported and clamped boundary conditions are clearly visualized. The distribution of the normal and shear stresses enables a good understanding of the plate critical points locations. It was found that strong tensile and compressive membrane stresses exist at various points near the plate edges, creating potential failure hazards.
Open AccessLarge Deflections of Thin-Walled Plates under Transverse Loading—Investigation of the Generated In-Plane Stresses
Thin-walled plates subjected to transverse loading undergoing large deflection have been the topic of a large number of studies. However, there is still a lack of information about the nature and the distribution membrane stresses generated under large deflections. The purpose of this paper is to calculate and display the distribution of the generated stresses and the respective deflections on the entire rectangular plate area. Finite element analysis results for thin-walled plates with aspect ratios of 1, 2 and 5, on movable and immovable edges simply supported and clamped boundary conditions are clearly visualized. The distribution of the normal and shear stresses enables a good understanding of the plate critical points locations. It was found that strong tensile and compressive membrane stresses exist at various points near the plate edges, creating potential failure hazards.
- Open Access
Investigation of a Morphing Wing Capable of Airfoil and Span Adjustment Using a Retractable Folding Mechanism
The presented aircraft is capable of alternating between two singular working points by folding the exterior surfaces of the wing underneath the interior surfaces. This allows for a significant change in wingspan, lift surfaces, aspect ratio and airfoil (camber and thickness). The motivation for this type of morphing is twofold: The increase in wingspan due to unfolding, results in an increased endurance of the aircraft, while the opposite process, which eliminates the camber of the airfoil and reduces the moment of inertia, is translated into improved manoeuvre capabilities. An analysis was performed to assess the additional endurance gained by the morphing capabilities, factoring in a spectrum of aircraft geometries and flight missions. It was concluded that this morphing concept can, in theory, improve the endurance up to 50% compared to the standard counterparts. The penalty due to the additional weight of the morphing mechanism was factored in, which had an adverse effect on the endurance improvement. The concept also calls for unique airfoil selection process. Selecting a proper airfoil for either working point, results in irregular airfoil geometry upon morphing. The two possibilities were subjected to analysis and wind tunnel testing.
Open AccessInvestigation of a Morphing Wing Capable of Airfoil and Span Adjustment Using a Retractable Folding Mechanism
The presented aircraft is capable of alternating between two singular working points by folding the exterior surfaces of the wing underneath the interior surfaces. This allows for a significant change in wingspan, lift surfaces, aspect ratio and airfoil (camber and thickness). The motivation for this type of morphing is twofold: The increase in wingspan due to unfolding, results in an increased endurance of the aircraft, while the opposite process, which eliminates the camber of the airfoil and reduces the moment of inertia, is translated into improved manoeuvre capabilities. An analysis was performed to assess the additional endurance gained by the morphing capabilities, factoring in a spectrum of aircraft geometries and flight missions. It was concluded that this morphing concept can, in theory, improve the endurance up to 50% compared to the standard counterparts. The penalty due to the additional weight of the morphing mechanism was factored in, which had an adverse effect on the endurance improvement. The concept also calls for unique airfoil selection process. Selecting a proper airfoil for either working point, results in irregular airfoil geometry upon morphing. The two possibilities were subjected to analysis and wind tunnel testing.
- Open Access
Determination of biophysical parameters for enhancement of human osteoblast proliferation by mechanical vibration in the infrasonic frequency range
Experimental methods for studying an enhancement of osteoblast proliferation in vitro provide tools for the research of biochemical processes involved in bone turnover in vivo. Some of the current methods used for this purpose are based on the ability of the osteoblasts to enhance proliferation by mechanical stimulation. We describe an experimental approach of biomechanical stimulation of cultured human osteoblast-like cells by vibration. This method is based on the specially designed controlled vibration setup that consists of an electric actuator, with horizontally mounted well plate containing cell cultures. Previously this method found to be effective to enhance cell proliferation, but the exact mechanical parameters of effective vibration were elusive. The current low friction system for mechanical stimulation of osteoblast-like cells in vitro provides recording of narrow range mechanical parameters in the infrasonic spectrum. We exposed human osteoblast-like cells in explant monolayer culture to mechanical vibration in the 10-70Hz range of frequencies and found that 50-70 Hz of vibration frequency is optimal for inducing osteoblast proliferation that was deduced from interrelation between unchanged cell number in culture samples with significant decrease in cell death rate (decreased LDH activity in culture media, p<.05) and with parallel decrease of their maturation level (p<.01). In this report we determined the optimal mechanical parameters and excitation protocol for induction of osteoblast proliferation in vitro by using a tunable and versatile mechanical platform, which can be used in the research of cell mechanotransduction.
Open AccessDetermination of biophysical parameters for enhancement of human osteoblast proliferation by mechanical vibration in the infrasonic frequency range
Experimental methods for studying an enhancement of osteoblast proliferation in vitro provide tools for the research of biochemical processes involved in bone turnover in vivo. Some of the current methods used for this purpose are based on the ability of the osteoblasts to enhance proliferation by mechanical stimulation. We describe an experimental approach of biomechanical stimulation of cultured human osteoblast-like cells by vibration. This method is based on the specially designed controlled vibration setup that consists of an electric actuator, with horizontally mounted well plate containing cell cultures. Previously this method found to be effective to enhance cell proliferation, but the exact mechanical parameters of effective vibration were elusive. The current low friction system for mechanical stimulation of osteoblast-like cells in vitro provides recording of narrow range mechanical parameters in the infrasonic spectrum. We exposed human osteoblast-like cells in explant monolayer culture to mechanical vibration in the 10-70Hz range of frequencies and found that 50-70 Hz of vibration frequency is optimal for inducing osteoblast proliferation that was deduced from interrelation between unchanged cell number in culture samples with significant decrease in cell death rate (decreased LDH activity in culture media, p<.05) and with parallel decrease of their maturation level (p<.01). In this report we determined the optimal mechanical parameters and excitation protocol for induction of osteoblast proliferation in vitro by using a tunable and versatile mechanical platform, which can be used in the research of cell mechanotransduction.
- Open Access
Analysis and Experimental Validation of a Piezoelectric Harvester with Enhanced Frequency Bandwidth
The use of a single bimorph as a harmonic oscillator aimed at harvesting vibrational energy is not effective due to its inherent narrow frequency bandwidth stemming from the need to adjust the natural frequency of the harvester to the platform excitation frequencies. Therefore, the present research focuses on the development, manufacturing, and testing of an advanced system based on three bimorphs, capable of adjusting their natural frequencies using tip end masses, and interconnected by springs, thus enlarging the system’s bandwidth. An analytical model was developed for three bimorphs interconnected by two springs with three end masses. The model can predict the output generated voltage from each bimorph, and then the total output power is measured on a given outside resistor as a function of the material properties, the geometric dimensions of the vibrating beams, the end-masses, and the spring constants. The analytical model was then compared with data in the literature, yielding a good correlation. To further increase the reliability of the model, a test set-up was designed and manufactured that included three bimorphs with three end-masses connected by two springs. The system was excited using a shaker, and the output voltage was measured for each bimorph for various configurations. Then, the analytical model was tuned based on the test results by introducing two factors, the quality and the stiffness factors, and the predictions of the calibrated analytical model were compared with the experimental results, yielding a good correlation. The calibrated analytical model was then used to perform a comprehensive parametric investigation for two and three bimorphs systems, in which the influences of various parameters—like spring constant, mass value, thickness, and width and length of the bimorph and the substrate beam—on the output generated power were investigated. The main conclusion from this parametric investigation was that by correctly choosing the geometric sizes of the cantilevers, the adequate tip end masses, and the ratio between constants of the springs, the frequency bandwidth is expanded yielding a higher harvested power. Typical harvested power of the present designed system can reach up to 20 mW at the first natural frequency and up to 5 mW for the second natural frequency.
Open AccessAnalysis and Experimental Validation of a Piezoelectric Harvester with Enhanced Frequency Bandwidth
The use of a single bimorph as a harmonic oscillator aimed at harvesting vibrational energy is not effective due to its inherent narrow frequency bandwidth stemming from the need to adjust the natural frequency of the harvester to the platform excitation frequencies. Therefore, the present research focuses on the development, manufacturing, and testing of an advanced system based on three bimorphs, capable of adjusting their natural frequencies using tip end masses, and interconnected by springs, thus enlarging the system’s bandwidth. An analytical model was developed for three bimorphs interconnected by two springs with three end masses. The model can predict the output generated voltage from each bimorph, and then the total output power is measured on a given outside resistor as a function of the material properties, the geometric dimensions of the vibrating beams, the end-masses, and the spring constants. The analytical model was then compared with data in the literature, yielding a good correlation. To further increase the reliability of the model, a test set-up was designed and manufactured that included three bimorphs with three end-masses connected by two springs. The system was excited using a shaker, and the output voltage was measured for each bimorph for various configurations. Then, the analytical model was tuned based on the test results by introducing two factors, the quality and the stiffness factors, and the predictions of the calibrated analytical model were compared with the experimental results, yielding a good correlation. The calibrated analytical model was then used to perform a comprehensive parametric investigation for two and three bimorphs systems, in which the influences of various parameters—like spring constant, mass value, thickness, and width and length of the bimorph and the substrate beam—on the output generated power were investigated. The main conclusion from this parametric investigation was that by correctly choosing the geometric sizes of the cantilevers, the adequate tip end masses, and the ratio between constants of the springs, the frequency bandwidth is expanded yielding a higher harvested power. Typical harvested power of the present designed system can reach up to 20 mW at the first natural frequency and up to 5 mW for the second natural frequency.
- Open Access
- 22 January 2017
- Published by SAGE Publications in International Journal of Mechanical Engineering Education
- Vol. 45  (2) , 184-193
The impact of root flexibility on the fundamental frequency of a restrained cantilever beam
This study presents the theoretical and experimental studies of the impact of root flexibility on the fundamental frequency of the free bending vibration of a uniform Euler–Bernoulli cantilever beam elastically restrained at the root. The dispersion relation between the natural frequency and modal number has been derived and solved numerically and approximately using the series method of the expansion in terms of the modal number. It is shown that the approximate solution is reduced to the empirical Dunkerley rule, which is sound not universally true. A commercial force sensor is used for the experimental detection of the effect of root flexibility on the fundamental frequency of bending vibrations of a cantilevered beam. The strip-shape specimen attached to the force sensor forms a cantilever beam restrained at the root against rotation and translation and it fundamental frequency is identified. The results of measurements for a series of industrial materials are compared with exact calculations and those predicted by Dunkerley’s formula and an excellent agreement is observed.
- 22 January 2017
- Published by SAGE Publications in International Journal of Mechanical Engineering Education
- Vol. 45  (2) , 184-193
Open AccessThe impact of root flexibility on the fundamental frequency of a restrained cantilever beam
This study presents the theoretical and experimental studies of the impact of root flexibility on the fundamental frequency of the free bending vibration of a uniform Euler–Bernoulli cantilever beam elastically restrained at the root. The dispersion relation between the natural frequency and modal number has been derived and solved numerically and approximately using the series method of the expansion in terms of the modal number. It is shown that the approximate solution is reduced to the empirical Dunkerley rule, which is sound not universally true. A commercial force sensor is used for the experimental detection of the effect of root flexibility on the fundamental frequency of bending vibrations of a cantilevered beam. The strip-shape specimen attached to the force sensor forms a cantilever beam restrained at the root against rotation and translation and it fundamental frequency is identified. The results of measurements for a series of industrial materials are compared with exact calculations and those predicted by Dunkerley’s formula and an excellent agreement is observed.
- 1 January 2017
- Published by Elsevier
- p. 619-691
Test results on the stability and vibrations of composite shells
- 1 January 2017
- Published by Elsevier
- p. 619-691
Test results on the stability and vibrations of composite shells