Ashraf Mohamed Heniegal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ashraf Mohamed Heniegal has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
ALsaeed Abdel SalamMaaty
1 shared publication- Ahmed T. Baraghith
Structural Engineering Department, Faculty of Engineering, Tanta University
1 shared publication Alan Richardson
1 shared publicationAlsaeed Abd El Salam Maaty
1 shared publicationAmr Basuoni Ibrahim Al-Samahy
1 shared publicationGhada Abd Elhameed
Building Materials Research and Quality Control Institute, Housing and Building National Research Center, Egypt
1 shared publication
Latest Publications
- Open Access
- 1 September 2024
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 24 (4) , 567-577
Ultimate Response of Strengthened RC Beams in the Flexural Using Plain Cementitious Composites Layer
This paper aims to study the efficiency of using prefabricated layers made from plain cementitious composite materials for enhancing the flexural behavior of reinforced concrete (RC) continuous beams. The strengthening system was applied at 20...
- 1 September 2024
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 24 (4) , 567-577
Open AccessUltimate Response of Strengthened RC Beams in the Flexural Using Plain Cementitious Composites Layer
This paper aims to study the efficiency of using prefabricated layers made from plain cementitious composite materials for enhancing the flexural behavior of reinforced concrete (RC) continuous beams. The strengthening system was applied at 20...
- 1 November 2017
- Published by Elsevier in Construction and Building Materials
- Vol. 155, 846-851
Effect of silica fume and steel slag coarse aggregate on the corrosion resistance of steel bars
- 1 November 2017
- Published by Elsevier in Construction and Building Materials
- Vol. 155, 846-851
Effect of silica fume and steel slag coarse aggregate on the corrosion resistance of steel bars
- 15 October 2017
- Published by eSAT Publishing House in International Journal of Research in Engineering and Technology
- Vol. 6 (10) , 99-113
PERFORMANCE EVALUATION OF STRUCTURAL LIGHTWEIGHT CONCRETE INCORPORATING ALUMINUM POWDER AND PUMICE IN FIRE CONDITION
- 15 October 2017
- Published by eSAT Publishing House in International Journal of Research in Engineering and Technology
- Vol. 6 (10) , 99-113
PERFORMANCE EVALUATION OF STRUCTURAL LIGHTWEIGHT CONCRETE INCORPORATING ALUMINUM POWDER AND PUMICE IN FIRE CONDITION
- Open Access
- 1 March 2017
- Published by College Publishing in Journal of Green Building
- Vol. 12 (2) , 59-78
OPTIMAL PERFORMANCE CHARACTERISTICS OF MORTAR INCORPORATING PHASE CHANGE MATERIALS AND SILICA FUME
This paper examines the thermal performance of 20 different mortar mixes, which were prepared in order to study the behaviour of mortar incorporating Phase Change Materials (PCM). The PCM was used at a rate of 10, 20 and 30% by weight of total solid materials. Silica fume was added to the mixes by 10, 20, 30 and 50% by weight of cement to enhance the mortar properties. Mortars which incorporate phase-change materials (PCM) have the capability to help regulate the temperature inside buildings, contributing to the thermal comfort while decreasing the amount of mechanical heating and cooling energy required, therefore they have the potential to reduce building carbon emissions. The mechanical characteristics and physical properties of the mortar with PCM were studied. The results show that mortar with Phase Change Materials up to PCM20% can be used with an optimal compressive strength. Silica fume (SF), up to a 20% SF addition, enhanced the mechanical properties of the mortar.
- 1 March 2017
- Published by College Publishing in Journal of Green Building
- Vol. 12 (2) , 59-78
Open AccessOPTIMAL PERFORMANCE CHARACTERISTICS OF MORTAR INCORPORATING PHASE CHANGE MATERIALS AND SILICA FUME
This paper examines the thermal performance of 20 different mortar mixes, which were prepared in order to study the behaviour of mortar incorporating Phase Change Materials (PCM). The PCM was used at a rate of 10, 20 and 30% by weight of total solid materials. Silica fume was added to the mixes by 10, 20, 30 and 50% by weight of cement to enhance the mortar properties. Mortars which incorporate phase-change materials (PCM) have the capability to help regulate the temperature inside buildings, contributing to the thermal comfort while decreasing the amount of mechanical heating and cooling energy required, therefore they have the potential to reduce building carbon emissions. The mechanical characteristics and physical properties of the mortar with PCM were studied. The results show that mortar with Phase Change Materials up to PCM20% can be used with an optimal compressive strength. Silica fume (SF), up to a 20% SF addition, enhanced the mechanical properties of the mortar.
- Open Access
- 1 March 2016
- Published by Egyptian Knowledge Bank in Port-Said Engineering Research Journal
- Vol. 20 (1) , 78-89
Properties of Geopolymer Mortar Containing Cement Kiln Dust (by-pass) as Partial Replacement Material for Low Calcium Fly Ash
This paper presents the results of a study held to compare the properties of geopolymer mortar prepared with the use of class C fly ash. Utilization of cement kiln dust (by-pass) with its high alkali content in the activation of geopolymer mortar specimens to create nonconventional cementitious binders was investigated. Many different geopolymer mortar mixtures were tested, all prepared by using fly ash-to-sand ratio of 1:3. Mixtures evaluation was based upon replacing the fly ash with cement kiln dust (by-pass) in the selected mixtures. The cement kiln dust (by-pass) content percentages were 5%, 10%, 15% and 20% by weight of fly ash as a partial replacement. Alkaline liquid to fly ash ratio of 0.50 was used. At the used alkaline liquid to fly ash ratio, the strength developments have been observed at 3, 7, and 28 days. Geopolymer mortar specimens were prepared with different concentrations of NaOH solution of M10, M14 and M16 and were cured at 60 ºC for 24 hours inside an oven. Thus, it is necessary to study the effects of the geopolymer binder on the behavior of compressive strength of geopolymer mortar. In this study, the Local Alkaline Activator in Egypt and Natural River sand as a fine aggregate in fly ash based-geopolymer mortar was investigated. This paper illustrates the development of mechanical properties. Hence it has been found that the compressive strength for geopolymer mortar at 28 days was in the range of 29.9MPa – 41.6MPa
- 1 March 2016
- Published by Egyptian Knowledge Bank in Port-Said Engineering Research Journal
- Vol. 20 (1) , 78-89
Open AccessProperties of Geopolymer Mortar Containing Cement Kiln Dust (by-pass) as Partial Replacement Material for Low Calcium Fly Ash
This paper presents the results of a study held to compare the properties of geopolymer mortar prepared with the use of class C fly ash. Utilization of cement kiln dust (by-pass) with its high alkali content in the activation of geopolymer mortar specimens to create nonconventional cementitious binders was investigated. Many different geopolymer mortar mixtures were tested, all prepared by using fly ash-to-sand ratio of 1:3. Mixtures evaluation was based upon replacing the fly ash with cement kiln dust (by-pass) in the selected mixtures. The cement kiln dust (by-pass) content percentages were 5%, 10%, 15% and 20% by weight of fly ash as a partial replacement. Alkaline liquid to fly ash ratio of 0.50 was used. At the used alkaline liquid to fly ash ratio, the strength developments have been observed at 3, 7, and 28 days. Geopolymer mortar specimens were prepared with different concentrations of NaOH solution of M10, M14 and M16 and were cured at 60 ºC for 24 hours inside an oven. Thus, it is necessary to study the effects of the geopolymer binder on the behavior of compressive strength of geopolymer mortar. In this study, the Local Alkaline Activator in Egypt and Natural River sand as a fine aggregate in fly ash based-geopolymer mortar was investigated. This paper illustrates the development of mechanical properties. Hence it has been found that the compressive strength for geopolymer mortar at 28 days was in the range of 29.9MPa – 41.6MPa
- Open Access
- 1 June 2015
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 54 (2) , 183-195
Simulation of the behavior of pressurized underwater concrete
- 1 June 2015
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 54 (2) , 183-195
Open AccessSimulation of the behavior of pressurized underwater concrete
- 1 December 2014
- Published by International Organization of Scientific Research in IOSR Journal of Engineering
- Vol. 4 (12) , 1-11
Performance of Concrete Incorporating Industrial and Agricultural Wastes
- 1 December 2014
- Published by International Organization of Scientific Research in IOSR Journal of Engineering
- Vol. 4 (12) , 1-11
Performance of Concrete Incorporating Industrial and Agricultural Wastes