Tim Arnold
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Tim Arnold has a total of 398 co-authors. Here are the top co-authors by number of shared publications:
- Alistair Manning
Hadley Centre, Met Office, Exeter, UK
43 shared publications - Simon O'DOherty
School of Chemistry, University of Bristol, Bristol, UK
43 shared publications - Chris Rennick
National Physical Laboratory, Teddington, UK
37 shared publications - Dickon Young
School of Chemistry, University of Bristol, Bristol, UK
32 shared publications - Kieran M. Stanley
School of Chemistry, University of Bristol, Bristol, UK
28 shared publications - Matthew Rigby
Atmospheric Chemistry Research Group, School of Chemistry, University of Bristol, Bristol, UK
27 shared publications
Latest Publications
- Open Access
- 13 August 2026
- Published by Copernicus GmbH in Atmospheric Chemistry and Physics
- Vol. 26 (15) , 11421-11448
Using high frequency observations of δ 13 C-CH 4 and δ 2 H-CH 4 and uncertain regional isotopic signatures to estimate sources of UK methane emissions
Methane is emitted from a range of anthropogenic and natural sources, and identifying these sources is important for emissions monitoring and mitigation. Different sources emit methane with different isotopic signatures. However, these signatures can vary spatially and temporally and are often not well understood. Top-down inverse methods can be used with measurements of methane mole fractions to estimate total emissions of methane from all sources. Here, we present an inverse system for concurrently estimating regional fossil-fuel (FF) and non-fossil-fuel (non-FF) emissions, using isotope ratio observations and considering uncertainty in the isotopic signatures. This method is highly adaptable and could be used to estimate emissions from any number of sources. Synthetic data tests with this method show that this inverse system can accurately estimate FF and non-FF methane emissions across the UK, when isotopic source signatures are fixed at known values. However, emissions estimation becomes less accurate when source signature uncertainties are increased to over approximately 50 % of their likely ranges. In a real-world test of this method, we estimated south-east UK FF and non-FF emissions using high-frequency δ 13 C-CH 4 and δ 2 H-CH 4 observations from one UK site, with source signature uncertainties reflecting our current understanding of these values. Results show only a limited impact on emissions uncertainty and magnitude, when compared with a methane-only inversion. This suggests that both an expansion of the UK network of isotope ratio observations and an improved understanding of isotopic signatures is required for this method to be effective in estimating UK FF and non-FF methane emissions with reduced uncertainty compared to traditional inverse methods.
- 13 August 2026
- Published by Copernicus GmbH in Atmospheric Chemistry and Physics
- Vol. 26 (15) , 11421-11448
Open AccessUsing high frequency observations of δ 13 C-CH 4 and δ 2 H-CH 4 and uncertain regional isotopic signatures to estimate sources of UK methane emissions
Methane is emitted from a range of anthropogenic and natural sources, and identifying these sources is important for emissions monitoring and mitigation. Different sources emit methane with different isotopic signatures. However, these signatures can vary spatially and temporally and are often not well understood. Top-down inverse methods can be used with measurements of methane mole fractions to estimate total emissions of methane from all sources. Here, we present an inverse system for concurrently estimating regional fossil-fuel (FF) and non-fossil-fuel (non-FF) emissions, using isotope ratio observations and considering uncertainty in the isotopic signatures. This method is highly adaptable and could be used to estimate emissions from any number of sources. Synthetic data tests with this method show that this inverse system can accurately estimate FF and non-FF methane emissions across the UK, when isotopic source signatures are fixed at known values. However, emissions estimation becomes less accurate when source signature uncertainties are increased to over approximately 50 % of their likely ranges. In a real-world test of this method, we estimated south-east UK FF and non-FF emissions using high-frequency δ 13 C-CH 4 and δ 2 H-CH 4 observations from one UK site, with source signature uncertainties reflecting our current understanding of these values. Results show only a limited impact on emissions uncertainty and magnitude, when compared with a methane-only inversion. This suggests that both an expansion of the UK network of isotope ratio observations and an improved understanding of isotopic signatures is required for this method to be effective in estimating UK FF and non-FF methane emissions with reduced uncertainty compared to traditional inverse methods.
- Open Access
- 7 April 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-40
Comment on egusphere-2026-779
Methane is emitted from a range of anthropogenic and natural sources, and identifying these sources is important for emissions monitoring and mitigation. Different sources emit methane with different isotopic signatures; however these signatures are often uncertain or vary spatially or temporally. Top-down inverse models can be used with measurement of methane mole fractions to estimate total emissions of methane from all sources. We present an inverse model for estimating regional fossil-fuel (FF) and non-fossil-fuel (non-FF) emissions concurrently, using isotope ratio observations and uncertain isotopic signatures. This method is highly adaptable and could be used to estimate emissions from any number of sources. Synthetic data tests with this method show that this model can accurately estimate FF and non-FF methane emissions across the UK, when isotopic source signatures are fixed at known values. However, emissions estimation becomes less accurate when source signature uncertainties rise above approximately 50 % of their likely ranges. In a real-world test of this method, we estimated south-east UK FF and non-FF emissions using high-frequency δ13C-CH4 and δ2H-CH4 observations from one UK site, with source signature uncertainties reflecting our current understanding of these values. Results show a limited impact on emissions uncertainty or magnitude, when compared with output from an inversion using only mole fraction observations. This suggests that both the ongoing expansion of isotope ratio observations and an improved understanding of isotopic signatures is required for this method to be used to estimate UK FF and non-FF methane emissions, with reduced uncertainty compared to traditional inverse methods.
- 7 April 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-40
Open AccessComment on egusphere-2026-779
Methane is emitted from a range of anthropogenic and natural sources, and identifying these sources is important for emissions monitoring and mitigation. Different sources emit methane with different isotopic signatures; however these signatures are often uncertain or vary spatially or temporally. Top-down inverse models can be used with measurement of methane mole fractions to estimate total emissions of methane from all sources. We present an inverse model for estimating regional fossil-fuel (FF) and non-fossil-fuel (non-FF) emissions concurrently, using isotope ratio observations and uncertain isotopic signatures. This method is highly adaptable and could be used to estimate emissions from any number of sources. Synthetic data tests with this method show that this model can accurately estimate FF and non-FF methane emissions across the UK, when isotopic source signatures are fixed at known values. However, emissions estimation becomes less accurate when source signature uncertainties rise above approximately 50 % of their likely ranges. In a real-world test of this method, we estimated south-east UK FF and non-FF emissions using high-frequency δ13C-CH4 and δ2H-CH4 observations from one UK site, with source signature uncertainties reflecting our current understanding of these values. Results show a limited impact on emissions uncertainty or magnitude, when compared with output from an inversion using only mole fraction observations. This suggests that both the ongoing expansion of isotope ratio observations and an improved understanding of isotopic signatures is required for this method to be used to estimate UK FF and non-FF methane emissions, with reduced uncertainty compared to traditional inverse methods.
- Open Access
- 3 April 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-40
Comment on egusphere-2026-779
Methane is emitted from a range of anthropogenic and natural sources, and identifying these sources is important for emissions monitoring and mitigation. Different sources emit methane with different isotopic signatures; however these signatures are often uncertain or vary spatially or temporally. Top-down inverse models can be used with measurement of methane mole fractions to estimate total emissions of methane from all sources. We present an inverse model for estimating regional fossil-fuel (FF) and non-fossil-fuel (non-FF) emissions concurrently, using isotope ratio observations and uncertain isotopic signatures. This method is highly adaptable and could be used to estimate emissions from any number of sources. Synthetic data tests with this method show that this model can accurately estimate FF and non-FF methane emissions across the UK, when isotopic source signatures are fixed at known values. However, emissions estimation becomes less accurate when source signature uncertainties rise above approximately 50 % of their likely ranges. In a real-world test of this method, we estimated south-east UK FF and non-FF emissions using high-frequency δ13C-CH4 and δ2H-CH4 observations from one UK site, with source signature uncertainties reflecting our current understanding of these values. Results show a limited impact on emissions uncertainty or magnitude, when compared with output from an inversion using only mole fraction observations. This suggests that both the ongoing expansion of isotope ratio observations and an improved understanding of isotopic signatures is required for this method to be used to estimate UK FF and non-FF methane emissions, with reduced uncertainty compared to traditional inverse methods.
- 3 April 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-40
Open AccessComment on egusphere-2026-779
Methane is emitted from a range of anthropogenic and natural sources, and identifying these sources is important for emissions monitoring and mitigation. Different sources emit methane with different isotopic signatures; however these signatures are often uncertain or vary spatially or temporally. Top-down inverse models can be used with measurement of methane mole fractions to estimate total emissions of methane from all sources. We present an inverse model for estimating regional fossil-fuel (FF) and non-fossil-fuel (non-FF) emissions concurrently, using isotope ratio observations and uncertain isotopic signatures. This method is highly adaptable and could be used to estimate emissions from any number of sources. Synthetic data tests with this method show that this model can accurately estimate FF and non-FF methane emissions across the UK, when isotopic source signatures are fixed at known values. However, emissions estimation becomes less accurate when source signature uncertainties rise above approximately 50 % of their likely ranges. In a real-world test of this method, we estimated south-east UK FF and non-FF emissions using high-frequency δ13C-CH4 and δ2H-CH4 observations from one UK site, with source signature uncertainties reflecting our current understanding of these values. Results show a limited impact on emissions uncertainty or magnitude, when compared with output from an inversion using only mole fraction observations. This suggests that both the ongoing expansion of isotope ratio observations and an improved understanding of isotopic signatures is required for this method to be used to estimate UK FF and non-FF methane emissions, with reduced uncertainty compared to traditional inverse methods.
- Open Access
- 25 March 2026
- Published by Copernicus GmbH in EGUsphere
- Vol. 2026, 1-40
Using high frequency observations of δ 13 C-CH 4 and δ 2 H-CH 4 and uncertain regional isotopic signatures to estimate sources of UK methane emissions
Methane is emitted from a range of anthropogenic and natural sources, and identifying these sources is important for emissions monitoring and mitigation. Different sources emit methane with different isotopic signatures; however these signatures are often uncertain or vary spatially or temporally. Top-down inverse models can be used with measurement of methane mole fractions to estimate total emissions of methane from all sources. We present an inverse model for estimating regional fossil-fuel (FF) and non-fossil-fuel (non-FF) emissions concurrently, using isotope ratio observations and uncertain isotopic signatures. This method is highly adaptable and could be used to estimate emissions from any number of sources. Synthetic data tests with this method show that this model can accurately estimate FF and non-FF methane emissions across the UK, when isotopic source signatures are fixed at known values. However, emissions estimation becomes less accurate when source signature uncertainties rise above approximately 50 % of their likely ranges. In a real-world test of this method, we estimated south-east UK FF and non-FF emissions using high-frequency δ13C-CH4 and δ2H-CH4 observations from one UK site, with source signature uncertainties reflecting our current understanding of these values. Results show a limited impact on emissions uncertainty or magnitude, when compared with output from an inversion using only mole fraction observations. This suggests that both the ongoing expansion of isotope ratio observations and an improved understanding of isotopic signatures is required for this method to be used to estimate UK FF and non-FF methane emissions, with reduced uncertainty compared to traditional inverse methods.
- 25 March 2026
- Published by Copernicus GmbH in EGUsphere
- Vol. 2026, 1-40
Open AccessUsing high frequency observations of δ 13 C-CH 4 and δ 2 H-CH 4 and uncertain regional isotopic signatures to estimate sources of UK methane emissions
Methane is emitted from a range of anthropogenic and natural sources, and identifying these sources is important for emissions monitoring and mitigation. Different sources emit methane with different isotopic signatures; however these signatures are often uncertain or vary spatially or temporally. Top-down inverse models can be used with measurement of methane mole fractions to estimate total emissions of methane from all sources. We present an inverse model for estimating regional fossil-fuel (FF) and non-fossil-fuel (non-FF) emissions concurrently, using isotope ratio observations and uncertain isotopic signatures. This method is highly adaptable and could be used to estimate emissions from any number of sources. Synthetic data tests with this method show that this model can accurately estimate FF and non-FF methane emissions across the UK, when isotopic source signatures are fixed at known values. However, emissions estimation becomes less accurate when source signature uncertainties rise above approximately 50 % of their likely ranges. In a real-world test of this method, we estimated south-east UK FF and non-FF emissions using high-frequency δ13C-CH4 and δ2H-CH4 observations from one UK site, with source signature uncertainties reflecting our current understanding of these values. Results show a limited impact on emissions uncertainty or magnitude, when compared with output from an inversion using only mole fraction observations. This suggests that both the ongoing expansion of isotope ratio observations and an improved understanding of isotopic signatures is required for this method to be used to estimate UK FF and non-FF methane emissions, with reduced uncertainty compared to traditional inverse methods.
- Open Access
- 10 February 2026
- Published by American Chemical Society (ACS) in ACS Measurement Science Au
- Vol. 6 (2) , 291-302
Uncertainties in Calibration of an Optical Spectrometer for Measuring Isotope Ratios in Methane
The stable isotope ratios of carbon (δ13C(CH4)) and hydrogen (δ2H(CH4)) in methane (CH4) from atmospheric air samples provide a tracer that can help distinguish the relative contribution of emission sources. These can be continuously measured at atmospheric monitoring stations by optical isotope ratio spectrometer (OIRS) instruments, providing data that is complementary to isotope ratio mass spectrometry (IRMS) measurements. OIRS instruments directly measure the amount fraction of the 12CH4, 13CH4, and 12CH3 2H isotopologues, in contrast to the IRMS method of conversion to CO2 and H2, so they have different calibration needs related to reference materials (RMs) and analysis protocol. We use a single high-purity source of CH4, which has been isotopically characterized by IRMS, to produce two calibration RMs that bracket the sample in amount fraction. The isotope ratio measurement is calibrated via the isotopologue amount fraction, which is used to derive analytical expressions for the combined uncertainty. We test this approach using a 550 μmol mol–1 sample (representative of the amount fraction produced from air sampled by the NPL preconcentrator) prepared from a separate CH4 source. The combined standard uncertainty for the isotope ratio of this sample is 0.19 ‰ for δ13C(CH4) and 1.1 ‰ for δ2H(CH4), including uncertainty contributions from the isotopic assignment of the CH4 used for the RMs, their gravimetric preparation, and the spectrometer noise. The dominant contribution to this is from the uncertainty in isotopic assignment of the CH4 used in RM preparation. The next largest contribution to the uncertainty budget is the measurement noise, estimated from the Allan-Werle deviation, and the smallest contribution is from the preparation uncertainty in the total CH4 amount fraction in the RMs. We demonstrate that preparing the bracketing RMs from a common CH4 source results in correlations between isotopologue amount fractions and that neglecting this leads to an overestimation of the isotope ratio uncertainty.
- 10 February 2026
- Published by American Chemical Society (ACS) in ACS Measurement Science Au
- Vol. 6 (2) , 291-302
Open AccessUncertainties in Calibration of an Optical Spectrometer for Measuring Isotope Ratios in Methane
The stable isotope ratios of carbon (δ13C(CH4)) and hydrogen (δ2H(CH4)) in methane (CH4) from atmospheric air samples provide a tracer that can help distinguish the relative contribution of emission sources. These can be continuously measured at atmospheric monitoring stations by optical isotope ratio spectrometer (OIRS) instruments, providing data that is complementary to isotope ratio mass spectrometry (IRMS) measurements. OIRS instruments directly measure the amount fraction of the 12CH4, 13CH4, and 12CH3 2H isotopologues, in contrast to the IRMS method of conversion to CO2 and H2, so they have different calibration needs related to reference materials (RMs) and analysis protocol. We use a single high-purity source of CH4, which has been isotopically characterized by IRMS, to produce two calibration RMs that bracket the sample in amount fraction. The isotope ratio measurement is calibrated via the isotopologue amount fraction, which is used to derive analytical expressions for the combined uncertainty. We test this approach using a 550 μmol mol–1 sample (representative of the amount fraction produced from air sampled by the NPL preconcentrator) prepared from a separate CH4 source. The combined standard uncertainty for the isotope ratio of this sample is 0.19 ‰ for δ13C(CH4) and 1.1 ‰ for δ2H(CH4), including uncertainty contributions from the isotopic assignment of the CH4 used for the RMs, their gravimetric preparation, and the spectrometer noise. The dominant contribution to this is from the uncertainty in isotopic assignment of the CH4 used in RM preparation. The next largest contribution to the uncertainty budget is the measurement noise, estimated from the Allan-Werle deviation, and the smallest contribution is from the preparation uncertainty in the total CH4 amount fraction in the RMs. We demonstrate that preparing the bracketing RMs from a common CH4 source results in correlations between isotopologue amount fractions and that neglecting this leads to an overestimation of the isotope ratio uncertainty.
- Open Access
- 8 December 2025
- Published by Copernicus GmbH in Earth System Science Data
- Vol. 17 (12) , 6889-6910
Global inventory of doubly substituted isotopologues of methane (Δ 13 CH 3 D and Δ 12 CH 2 D 2 )
Measurements of methane (CH4) molecules containing two rare isotopes (13CH3D and 12CH2D2), also termed doubly substituted or “clumped” isotopologues, have the potential to provide two additional isotopic dimensions to help investigate the mechanisms underlying global atmospheric trends in CH4. In this work, we summarise the current state of research on doubly substituted CH4 isotopologues, with an emphasis on compiling results of all relevant work. The database comprises 1475 records compiled from the literature published until April 2025 (https://doi.org/10.5285/51ae627da5fb41b8a767ee6c653f83e6, Defratyka et al., 2025). For field samples, 40 % of records were sourced from natural gas reservoirs, while microbial terrestrial (e.g., agriculture, lake, wetland) samples account only for 12.5 %. Lakes samples contribute 75 % to collected microbial terrestrial samples. There is limited or no representation of samples coming from significant microbial CH4 sources to the atmosphere, like wetlands, agricultural practices and landfills. To date, laboratory experiments were mostly focused on microbial (28 % of samples from laboratory experiments) and pyrogenic (15 %) methanogenesis or anaerobic (16 %), and aerobic (8 %) CH4 oxidation, with only single study of photochemical oxidation via OH and Cl, which constitutes 5 % of the laboratory experiments entries. The distinct ranges of Δ13CH3D and Δ12CH2D2 values measured in these studies suggests their potential to improve our understanding of atmospheric CH4. This work provides an overview of the major gaps in measurements and identifies where further studies should be focussed to enable the highest impact on understanding global CH4.
- 8 December 2025
- Published by Copernicus GmbH in Earth System Science Data
- Vol. 17 (12) , 6889-6910
Open AccessGlobal inventory of doubly substituted isotopologues of methane (Δ 13 CH 3 D and Δ 12 CH 2 D 2 )
Measurements of methane (CH4) molecules containing two rare isotopes (13CH3D and 12CH2D2), also termed doubly substituted or “clumped” isotopologues, have the potential to provide two additional isotopic dimensions to help investigate the mechanisms underlying global atmospheric trends in CH4. In this work, we summarise the current state of research on doubly substituted CH4 isotopologues, with an emphasis on compiling results of all relevant work. The database comprises 1475 records compiled from the literature published until April 2025 (https://doi.org/10.5285/51ae627da5fb41b8a767ee6c653f83e6, Defratyka et al., 2025). For field samples, 40 % of records were sourced from natural gas reservoirs, while microbial terrestrial (e.g., agriculture, lake, wetland) samples account only for 12.5 %. Lakes samples contribute 75 % to collected microbial terrestrial samples. There is limited or no representation of samples coming from significant microbial CH4 sources to the atmosphere, like wetlands, agricultural practices and landfills. To date, laboratory experiments were mostly focused on microbial (28 % of samples from laboratory experiments) and pyrogenic (15 %) methanogenesis or anaerobic (16 %), and aerobic (8 %) CH4 oxidation, with only single study of photochemical oxidation via OH and Cl, which constitutes 5 % of the laboratory experiments entries. The distinct ranges of Δ13CH3D and Δ12CH2D2 values measured in these studies suggests their potential to improve our understanding of atmospheric CH4. This work provides an overview of the major gaps in measurements and identifies where further studies should be focussed to enable the highest impact on understanding global CH4.
- Open Access
- 18 June 2025
- Published by Copernicus GmbH
Supplementary material to "Global inventory of doubly substituted isotopologues of methane (Δ 13 CH 3 D and Δ 12 CH 2 D 2 )"
- 18 June 2025
- Published by Copernicus GmbH
Open AccessSupplementary material to "Global inventory of doubly substituted isotopologues of methane (Δ 13 CH 3 D and Δ 12 CH 2 D 2 )"
- Open Access
- 18 June 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-30
Global inventory of doubly substituted isotopologues of methane (Δ 13 CH 3 D and Δ 12 CH 2 D 2 )
Measurements of methane (CH4) molecules containing two rare isotopes (13CH3D and 12CH2D2), also termed doubly substituted or ‘clumped’ isotopologues, have the potential to provide two additional isotopic dimensions to help investigating mechanisms producing the recent global trends and CH4 budget over decadal timescale. In this work, we summarise the current state of research on doubly substituted CH4 isotopologues, with an emphasis on compiling results of all relevant work. The database comprises 1475 records compiled from the literature published until April 2025 (https://dx.doi.org/10.5285/51ae627da5fb41b8a767ee6c653f83e6). For field samples, 40 % of records were sourced from natural gas reservoirs, while microbial terrestrial (e.g., agriculture, lake, wetland) samples account only for 12.5 %. Lakes samples contribute 75 % to collected microbial terrestrial samples. There is limited or no representation of samples coming from significant microbial CH4 sources to the atmosphere, like wetlands, agriculture and landfill. To date, laboratory experiments were mostly focused on microbial (28 % of samples from laboratory experiments) and pyrogenic (15 %) methanogenesis or anaerobic (16 %), and aerobic (8 %) CH4 oxidation, and only a single contribution to studies of photochemical oxidation via OH and Cl (5 %). The distinct ranges of Δ13CH3D and Δ12CH2D2 values measured in these studies suggests their potential to improve our understanding of atmospheric CH4. This work provides an overview of the major gaps in measurements and identifies where further studies should be focussed to enable the highest immediate impact on understanding global CH4.
- 18 June 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-30
Open AccessGlobal inventory of doubly substituted isotopologues of methane (Δ 13 CH 3 D and Δ 12 CH 2 D 2 )
Measurements of methane (CH4) molecules containing two rare isotopes (13CH3D and 12CH2D2), also termed doubly substituted or ‘clumped’ isotopologues, have the potential to provide two additional isotopic dimensions to help investigating mechanisms producing the recent global trends and CH4 budget over decadal timescale. In this work, we summarise the current state of research on doubly substituted CH4 isotopologues, with an emphasis on compiling results of all relevant work. The database comprises 1475 records compiled from the literature published until April 2025 (https://dx.doi.org/10.5285/51ae627da5fb41b8a767ee6c653f83e6). For field samples, 40 % of records were sourced from natural gas reservoirs, while microbial terrestrial (e.g., agriculture, lake, wetland) samples account only for 12.5 %. Lakes samples contribute 75 % to collected microbial terrestrial samples. There is limited or no representation of samples coming from significant microbial CH4 sources to the atmosphere, like wetlands, agriculture and landfill. To date, laboratory experiments were mostly focused on microbial (28 % of samples from laboratory experiments) and pyrogenic (15 %) methanogenesis or anaerobic (16 %), and aerobic (8 %) CH4 oxidation, and only a single contribution to studies of photochemical oxidation via OH and Cl (5 %). The distinct ranges of Δ13CH3D and Δ12CH2D2 values measured in these studies suggests their potential to improve our understanding of atmospheric CH4. This work provides an overview of the major gaps in measurements and identifies where further studies should be focussed to enable the highest immediate impact on understanding global CH4.
- Open Access
- 9 June 2025
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 97 (24) , 12513-12520
In-Line Combustion System for the Measurement of δ13C–CH4 in Gas Reference Materials Using Optical Isotope Ratio Spectroscopy
Measurements of the stable carbon isotope ratio in methane (δ13C-CH4) are used in determining the source of CH4 emissions on local, regional, and global scales. To achieve the required level of data comparability for atmospheric monitoring networks, accurate gas reference materials of δ13C-CH4 in air are required with high levels of reproducibility. We describe a method to determine the δ13C-CH4 of CH4 in synthetic air reference materials reported against the Vienna Pee Dee Belemnite (VPDB) scale. The measurement principle converts CH4 into carbon dioxide (CO2) via direct combustion using a platinum catalyst. Subsequently, the CO2 resulting from CH4 combustion was analyzed for δ13C-CO2 using OIRS (optical isotope ratio spectroscopy) against CO2 in synthetic air reference materials traceable to the δ13CVPDB scale. The δ13C-CH4 of four nominally 410 μmol mol-1 CH4 in synthetic air reference materials, prepared in pairs from two CH4 sources with distinct δ13C-CH4 were certified with an average δ13C-CH4 of -39.07‰ and -51.91‰. Measurement reproducibility within 0.17‰ was demonstrated between measurements of the two reference materials from each CH4 source. Agreement to traceable measurements of the pure CH4 was achieved within reported measurement reproducibility. Combined expanded uncertainties (k= 2) between 0.4 and 1.5‰ have been demonstrated. The sensitives of the conversion system to flow rate have been assessed and found to have a negligible impact on the certification of δ13C-CH4. Thus, we demonstrate that a combustion system coupled to OIRS measurement of CO2 can provide a means of useful measurement of δ13C-CH4 traceable to VPDB.
- 9 June 2025
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 97 (24) , 12513-12520
Open AccessIn-Line Combustion System for the Measurement of δ13C–CH4 in Gas Reference Materials Using Optical Isotope Ratio Spectroscopy
Measurements of the stable carbon isotope ratio in methane (δ13C-CH4) are used in determining the source of CH4 emissions on local, regional, and global scales. To achieve the required level of data comparability for atmospheric monitoring networks, accurate gas reference materials of δ13C-CH4 in air are required with high levels of reproducibility. We describe a method to determine the δ13C-CH4 of CH4 in synthetic air reference materials reported against the Vienna Pee Dee Belemnite (VPDB) scale. The measurement principle converts CH4 into carbon dioxide (CO2) via direct combustion using a platinum catalyst. Subsequently, the CO2 resulting from CH4 combustion was analyzed for δ13C-CO2 using OIRS (optical isotope ratio spectroscopy) against CO2 in synthetic air reference materials traceable to the δ13CVPDB scale. The δ13C-CH4 of four nominally 410 μmol mol-1 CH4 in synthetic air reference materials, prepared in pairs from two CH4 sources with distinct δ13C-CH4 were certified with an average δ13C-CH4 of -39.07‰ and -51.91‰. Measurement reproducibility within 0.17‰ was demonstrated between measurements of the two reference materials from each CH4 source. Agreement to traceable measurements of the pure CH4 was achieved within reported measurement reproducibility. Combined expanded uncertainties (k= 2) between 0.4 and 1.5‰ have been demonstrated. The sensitives of the conversion system to flow rate have been assessed and found to have a negligible impact on the certification of δ13C-CH4. Thus, we demonstrate that a combustion system coupled to OIRS measurement of CO2 can provide a means of useful measurement of δ13C-CH4 traceable to VPDB.
- Open Access
- 18 March 2025
- Published by Copernicus GmbH
Addressing research challenges of environmental change at the global scale via Research Infrastructures collaboration and alignment
The forest landscape is of global importance for net radiative forcing. As the world warms, feedbacks within the ecosystems alter greenhouse gas (GHG) balances. Coordinated observations of GHG fluxes and concentrations, and of more chemically active species, as well as variables describing the ecosystem, are essential for understanding and prediction of feedbacks. ICOS (Integrated Carbon Observation System), ACTRIS (Aerosol, Clouds and Trace Gas Research Infrastructure) and SITES (Swedish Infrastructure for Ecosystem Science) have already provided >10 years of data for open science. These measurements on the carbon cycle, air quality, and ecosystem behavior already provide key information for quantifying GHG emissions and sinks, and investigating feedbacks under a changing climate. ACTRIS Sweden, ICOS Sweden and SITES have developed a strategic plan for enhanced cooperation. This will better address the global challenge of understanding ecosystem influences on GHG fluxes as the climate warms, as well as the interplay of physical and chemical properties of the atmosphere on ecosystems. Before summarizing that plan for deeper cooperation, it is worth noting some more about these three national networks. ICOS and ACTRIS are already ERIC RIs and SITES is involved in efforts to establish eLTER (Integrated European Long-Term Ecosystem, Critical Zone and Socio-Ecological Research Infrastructure) as an ERIC RI as well. The three national RIs are active partners within their respective ERIC consortia and collaborate with other RIs in the ESFRI environment and climate domain. All stations and the FAIR data they provide are widely used within research, earth system observation, education (students, PhD, post docs), and as test sites for new instruments and methods within academia and private-sector companies. The stations of the three RIs are also incorporated into the Copernicus services. The management structure of the RIs are closely related to developments in earth observation at European and international levels. The strategic plan for enhanced cooperation between the three national RIs has a set of eight short term goals that should be achieved in the next 2-3 years. These include further enhancing co-location of measurements, integration of scientific leadership, as well as coordination of tools for accessing both the field sites and available data. This enhanced cooperation between the national networks of ACTRIS, ICOS and SITES also aims at five long terms goals. continuity of high-quality services strategic collaboration organizational optimization increased usage across our RIs fostering innovation As a result of the enhanced cooperation, the RIs will achieve a new level of collaboration in observation systems for atmospheric pollution, including the effects of this pollution and climate change on ecosystems. Joint approaches to strategic development and outreach will further maximize synergies between these complementary infrastructures, giving ACTRIS, ICOS and SITES a more central, coordinated role in supporting Earth system science, and societal decision-making in the context of the UN Sustainable Development Goals.
- 18 March 2025
- Published by Copernicus GmbH
Open AccessAddressing research challenges of environmental change at the global scale via Research Infrastructures collaboration and alignment
The forest landscape is of global importance for net radiative forcing. As the world warms, feedbacks within the ecosystems alter greenhouse gas (GHG) balances. Coordinated observations of GHG fluxes and concentrations, and of more chemically active species, as well as variables describing the ecosystem, are essential for understanding and prediction of feedbacks. ICOS (Integrated Carbon Observation System), ACTRIS (Aerosol, Clouds and Trace Gas Research Infrastructure) and SITES (Swedish Infrastructure for Ecosystem Science) have already provided >10 years of data for open science. These measurements on the carbon cycle, air quality, and ecosystem behavior already provide key information for quantifying GHG emissions and sinks, and investigating feedbacks under a changing climate. ACTRIS Sweden, ICOS Sweden and SITES have developed a strategic plan for enhanced cooperation. This will better address the global challenge of understanding ecosystem influences on GHG fluxes as the climate warms, as well as the interplay of physical and chemical properties of the atmosphere on ecosystems. Before summarizing that plan for deeper cooperation, it is worth noting some more about these three national networks. ICOS and ACTRIS are already ERIC RIs and SITES is involved in efforts to establish eLTER (Integrated European Long-Term Ecosystem, Critical Zone and Socio-Ecological Research Infrastructure) as an ERIC RI as well. The three national RIs are active partners within their respective ERIC consortia and collaborate with other RIs in the ESFRI environment and climate domain. All stations and the FAIR data they provide are widely used within research, earth system observation, education (students, PhD, post docs), and as test sites for new instruments and methods within academia and private-sector companies. The stations of the three RIs are also incorporated into the Copernicus services. The management structure of the RIs are closely related to developments in earth observation at European and international levels. The strategic plan for enhanced cooperation between the three national RIs has a set of eight short term goals that should be achieved in the next 2-3 years. These include further enhancing co-location of measurements, integration of scientific leadership, as well as coordination of tools for accessing both the field sites and available data. This enhanced cooperation between the national networks of ACTRIS, ICOS and SITES also aims at five long terms goals. continuity of high-quality services strategic collaboration organizational optimization increased usage across our RIs fostering innovation As a result of the enhanced cooperation, the RIs will achieve a new level of collaboration in observation systems for atmospheric pollution, including the effects of this pollution and climate change on ecosystems. Joint approaches to strategic development and outreach will further maximize synergies between these complementary infrastructures, giving ACTRIS, ICOS and SITES a more central, coordinated role in supporting Earth system science, and societal decision-making in the context of the UN Sustainable Development Goals.