Piotr Kaczynski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Piotr Kaczynski has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Ryszard Szwaba
Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland
11 shared publications - Piotr Doerffer
Gdansk University of Technology
10 shared publications - Pawel Flaszynski
Institute of Fluid-Flow Machinery, Polish Academy of Sciences (IMP-PAN), 80-231 Gdansk, Poland
5 shared publications - Adam Cenian
Air and Water Purification Department, The Institute of Fluid-Flow Machinery Polish Academy of Sciences, Fiszera 14 St., 80-231 Gdansk, Poland
2 shared publications - Ahmed H. Hanfy
Institute of Fluid-Flow Machinery, Polish Academy of Sciences (IMP-PAN), 80-231 Gdansk, Poland
2 shared publications - Chinh Chien Nguyen
Center for Advanced Chemistry, Institute of Research and Development
2 shared publications
Latest Publications
- Open Access
- 3 April 2026
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 11 (2) , 16
Experimental Investigation of Shock Boundary/Layer Interaction on a Fan Profile Under Various Inlet Conditions
Transonic compressors encounter significant challenges from shock formations due to high-speed supersonic blade tips, particularly at high altitudes where lower Reynolds numbers result in laminar boundary layer separation and increased mixing losses. Understanding shock wave–boundary layer interaction (SBLI) is essential for improving compressor performance. This study examines SBLI under varying Reynolds numbers, simulating higher altitude conditions in a transonic blow-down wind tunnel. Using an inlet valve setup to control inflow total pressure and Reynolds numbers, this study also reveals an increase in turbulence. The findings indicate that laminar-to-turbulent transition occurs upstream of the shock wave, resulting in interaction with a turbulent boundary layer, even at lower Reynolds numbers.
- 3 April 2026
- Published by MDPI AG in International Journal of Turbomachinery, Propulsion and Power
- Vol. 11 (2) , 16
Open AccessExperimental Investigation of Shock Boundary/Layer Interaction on a Fan Profile Under Various Inlet Conditions
Transonic compressors encounter significant challenges from shock formations due to high-speed supersonic blade tips, particularly at high altitudes where lower Reynolds numbers result in laminar boundary layer separation and increased mixing losses. Understanding shock wave–boundary layer interaction (SBLI) is essential for improving compressor performance. This study examines SBLI under varying Reynolds numbers, simulating higher altitude conditions in a transonic blow-down wind tunnel. Using an inlet valve setup to control inflow total pressure and Reynolds numbers, this study also reveals an increase in turbulence. The findings indicate that laminar-to-turbulent transition occurs upstream of the shock wave, resulting in interaction with a turbulent boundary layer, even at lower Reynolds numbers.
- Open Access
- 2 July 2025
- Published by Springer Nature
- p. 325-344
Surface Roughness Effect on Shock Boundary Layer Interaction on Compressor Rotor Profile
High-pressure ratios in transonic compressor rotors and fan blades pose challenges such as supersonic speeds and shock waves, which can result in boundary layer separation and potential performance issues. This study presents experimental research exploring the effect of surface roughness on shockwave-boundary layer interaction (SBLI). By employing various measurement techniques, the study provides a comprehensive overview of how surface roughness affects SBLI, enriching the dataset for internal flows across four specimens with different roughness parameters. The findings indicate that lower roughness surfaces lead to larger separation bubbles and more typical shock structures, whereas increased roughness results in smaller separation bubbles but higher flow instability.
- 2 July 2025
- Published by Springer Nature
- p. 325-344
Open AccessSurface Roughness Effect on Shock Boundary Layer Interaction on Compressor Rotor Profile
High-pressure ratios in transonic compressor rotors and fan blades pose challenges such as supersonic speeds and shock waves, which can result in boundary layer separation and potential performance issues. This study presents experimental research exploring the effect of surface roughness on shockwave-boundary layer interaction (SBLI). By employing various measurement techniques, the study provides a comprehensive overview of how surface roughness affects SBLI, enriching the dataset for internal flows across four specimens with different roughness parameters. The findings indicate that lower roughness surfaces lead to larger separation bubbles and more typical shock structures, whereas increased roughness results in smaller separation bubbles but higher flow instability.
- Open Access
- 26 May 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (11) , 5999
Analyzing and Predicting the Agronomic Effectiveness of Fertilizers Derived from Food Waste Using Data-Driven Models
This study evaluates and estimates the agronomic effectiveness of food waste-derived fertilizers by analyzing plant yield and the internal efficiency of nitrogen utilization (IENU) via statistical and machine learning models. A dataset of 448 cases from various food waste treatments gathered from our experiments and the existing literature was analyzed. Plant yield and IENU exhibited substantial variability, averaging 2268 ± 3099 kg/ha and 32.3 ± 92.5 kg N/ha, respectively. Ryegrass dominated (73.77%), followed by unspecified grass (10.76%), oats (4.87%), and lettuce (2.02%). Correlation analysis revealed that decomposition duration positively influenced plant yield and IENU (r = 0.42 and 0.44), while temperature and volatile solids had negative correlations. Machine learning models outperformed linear regression in predicting plant yield and IENU, especially after preprocessing to remove missing values and outliers. Random Forest and Cubist models showed strong generalization with high R2 (0.79–0.83) for plant yield, while Cubist predicted IENU well in testing, with RMSE = 3.83 and R2 = 0.78. These findings highlight machine learning’s ability to analyze complex datasets, improve agricultural decision-making, and optimize food waste utilization.
- 26 May 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (11) , 5999
Open AccessAnalyzing and Predicting the Agronomic Effectiveness of Fertilizers Derived from Food Waste Using Data-Driven Models
This study evaluates and estimates the agronomic effectiveness of food waste-derived fertilizers by analyzing plant yield and the internal efficiency of nitrogen utilization (IENU) via statistical and machine learning models. A dataset of 448 cases from various food waste treatments gathered from our experiments and the existing literature was analyzed. Plant yield and IENU exhibited substantial variability, averaging 2268 ± 3099 kg/ha and 32.3 ± 92.5 kg N/ha, respectively. Ryegrass dominated (73.77%), followed by unspecified grass (10.76%), oats (4.87%), and lettuce (2.02%). Correlation analysis revealed that decomposition duration positively influenced plant yield and IENU (r = 0.42 and 0.44), while temperature and volatile solids had negative correlations. Machine learning models outperformed linear regression in predicting plant yield and IENU, especially after preprocessing to remove missing values and outliers. Random Forest and Cubist models showed strong generalization with high R2 (0.79–0.83) for plant yield, while Cubist predicted IENU well in testing, with RMSE = 3.83 and R2 = 0.78. These findings highlight machine learning’s ability to analyze complex datasets, improve agricultural decision-making, and optimize food waste utilization.
- Open Access
- 30 April 2025
- Published by MDPI AG in Preprints.org
Analyzing and Predicting the Agronomic Effectiveness of Fertilizers Derived from Food Waste Using Data-Driven Models
This study evaluates and estimates the agronomic effectiveness of food waste-derived fertilizers by analyzing plant yield and the internal efficiency of nitrogen utilization (IENU) via statistical and machine learning models. A dataset of 448 cases from various food waste treatments from our experiments and literature was analyzed. Plant yield and IENU showed high variability, averaging 2268 ± 3099 kg/ha and 32.3 ± 92.5 kg N/ha, respectively. Ryegrass dominated (73.77%), followed by unspecified grass (10.76%), with oats (4.87%) and lettuce (2.02%). Correlation analysis revealed that decomposition duration positively influenced plant yield and IENU (r = 0.42, 0.44), while temperature and volatile solids had negative correlations. Machine learning outperformed linear regression to predict plant yield and IENU, especially after preprocessing to remove missing values and outliers. Random Forest and Cubist models showed strong generalization with high R² (0.79–0.83) for plant yield, while Cubist predicted IENU well in testing, with RMSE = 3.83 and R² = 0.78. These findings highlight machine learning’s ability to analyze complex datasets, improve agricultural decision-making, and optimize food waste utilization.
- 30 April 2025
- Published by MDPI AG in Preprints.org
Open AccessAnalyzing and Predicting the Agronomic Effectiveness of Fertilizers Derived from Food Waste Using Data-Driven Models
This study evaluates and estimates the agronomic effectiveness of food waste-derived fertilizers by analyzing plant yield and the internal efficiency of nitrogen utilization (IENU) via statistical and machine learning models. A dataset of 448 cases from various food waste treatments from our experiments and literature was analyzed. Plant yield and IENU showed high variability, averaging 2268 ± 3099 kg/ha and 32.3 ± 92.5 kg N/ha, respectively. Ryegrass dominated (73.77%), followed by unspecified grass (10.76%), with oats (4.87%) and lettuce (2.02%). Correlation analysis revealed that decomposition duration positively influenced plant yield and IENU (r = 0.42, 0.44), while temperature and volatile solids had negative correlations. Machine learning outperformed linear regression to predict plant yield and IENU, especially after preprocessing to remove missing values and outliers. Random Forest and Cubist models showed strong generalization with high R² (0.79–0.83) for plant yield, while Cubist predicted IENU well in testing, with RMSE = 3.83 and R² = 0.78. These findings highlight machine learning’s ability to analyze complex datasets, improve agricultural decision-making, and optimize food waste utilization.
- Open Access
Experimental Permeability and Porosity Determination of All-Oxide Ceramic Matrix Composite Material
This paper presents an investigation into the water permeability of an all-oxide ceramic matrix composite. To determine the parameters and characterize the water permeability of the ceramic composite material, an experimental study was carried out in which a dedicated test rig was constructed and commissioned. A total of five different configurations of composite tubes were tested. They differed in fibre roving strength, winding angle, fibre bundle arrangement during winding, and matrix grain size distribution. To better understand the internal structure of the analysed ceramic matrix composite material, the experimental study used scanning electron microscopy for microstructure and porosity observation. The tested tubes will be used as liners in an oxy-combustion chamber in future studies. The experiments obtained new and interesting results regarding the water permeability of the ceramic matrix composite with different structural parameters. It was also observed that, as with some porous materials, the permeability of ceramic matrix composites decreases with time as more and more liquid is pressed through it.
Open AccessExperimental Permeability and Porosity Determination of All-Oxide Ceramic Matrix Composite Material
This paper presents an investigation into the water permeability of an all-oxide ceramic matrix composite. To determine the parameters and characterize the water permeability of the ceramic composite material, an experimental study was carried out in which a dedicated test rig was constructed and commissioned. A total of five different configurations of composite tubes were tested. They differed in fibre roving strength, winding angle, fibre bundle arrangement during winding, and matrix grain size distribution. To better understand the internal structure of the analysed ceramic matrix composite material, the experimental study used scanning electron microscopy for microstructure and porosity observation. The tested tubes will be used as liners in an oxy-combustion chamber in future studies. The experiments obtained new and interesting results regarding the water permeability of the ceramic matrix composite with different structural parameters. It was also observed that, as with some porous materials, the permeability of ceramic matrix composites decreases with time as more and more liquid is pressed through it.
- Open Access
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
This paper describes some insights on applicability of a Selective Laser Melting and Direct Metal Laser Sintering technology-manufactured turbine blade models for aerodynamic tests in a wind tunnel. The principal idea behind this research was to assess the possibilities of using ‘raw’ DLMS printed turbine blade models for gas-flow experiments. The actual blade, manufactured using the DLMS technology, is assessed in terms of surface quality (roughness), geometrical shape and size (outline), quality of counterbores and quality of small diameter holes. The results are evaluated for the experimental aerodynamics standpoint. This field of application imposes requirements that have not yet been described in the literature. The experimental outcomes prove the surface quality does not suffice to conduct quantitative experiments. The holes that are necessary for pressure measurements in wind tunnel experiments cannot be reduced below 1 mm in diameter. The dimensional discrepancies are on the level beyond acceptable. Additionally, the problem of ‘reversed tolerance’, with the material building up and distorting the design, is visible in elements printed with the DLMS technology. The results indicate the necessity of post-machining of the printed elements prior their experimental usage, as their features in the ‘as fabricated’ state significantly disturb the flow conditions.
Open AccessSuitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
This paper describes some insights on applicability of a Selective Laser Melting and Direct Metal Laser Sintering technology-manufactured turbine blade models for aerodynamic tests in a wind tunnel. The principal idea behind this research was to assess the possibilities of using ‘raw’ DLMS printed turbine blade models for gas-flow experiments. The actual blade, manufactured using the DLMS technology, is assessed in terms of surface quality (roughness), geometrical shape and size (outline), quality of counterbores and quality of small diameter holes. The results are evaluated for the experimental aerodynamics standpoint. This field of application imposes requirements that have not yet been described in the literature. The experimental outcomes prove the surface quality does not suffice to conduct quantitative experiments. The holes that are necessary for pressure measurements in wind tunnel experiments cannot be reduced below 1 mm in diameter. The dimensional discrepancies are on the level beyond acceptable. Additionally, the problem of ‘reversed tolerance’, with the material building up and distorting the design, is visible in elements printed with the DLMS technology. The results indicate the necessity of post-machining of the printed elements prior their experimental usage, as their features in the ‘as fabricated’ state significantly disturb the flow conditions.
- Open Access
- 1 January 2021
- Published by Wiley in Shock and Vibration
- Vol. 2021 (1)
Transition Effect on the Flow Dynamics in a Compressor Blade Passage
An experimental investigation was carried out to study the effect of the boundary layer transition on the flow dynamics in the blade passage of a compressor cascade. A model of a turbine compressor passage was designed and assembled in a transonic wind tunnel for this purpose. Two different flow control methods were used in the experiment to induce the transition upstream of the shock wave, one concerning the microstep application and the other using distributed roughness strips. Two locations of spanwise microsteps for the transition trigger were chosen, one at the leading edge and the other closer to the shock wave position. The distributed roughness in the form of standard sandpaper strips with different heights was applied in three various locations on the blade upstream of the shock. The main objective of investigations is to present the influence of the laminar and turbulent shock wave‐boundary layer interaction on the flow dynamics in a compressor fan passage, and the specific objective is to show how the parameters of particular transition control methods affect the flow dynamics in the investigated channel. The major challenge for this research was to minimize the disturbance caused by the microstep or roughness to the laminar boundary layer, while still ensuring a successful transition. Very interesting results were obtained in the flow control application for the boundary layer transition control, demonstrating a positive effect on the flow unsteadiness in changing the nature of the interaction.
- 1 January 2021
- Published by Wiley in Shock and Vibration
- Vol. 2021 (1)
Open AccessTransition Effect on the Flow Dynamics in a Compressor Blade Passage
An experimental investigation was carried out to study the effect of the boundary layer transition on the flow dynamics in the blade passage of a compressor cascade. A model of a turbine compressor passage was designed and assembled in a transonic wind tunnel for this purpose. Two different flow control methods were used in the experiment to induce the transition upstream of the shock wave, one concerning the microstep application and the other using distributed roughness strips. Two locations of spanwise microsteps for the transition trigger were chosen, one at the leading edge and the other closer to the shock wave position. The distributed roughness in the form of standard sandpaper strips with different heights was applied in three various locations on the blade upstream of the shock. The main objective of investigations is to present the influence of the laminar and turbulent shock wave‐boundary layer interaction on the flow dynamics in a compressor fan passage, and the specific objective is to show how the parameters of particular transition control methods affect the flow dynamics in the investigated channel. The major challenge for this research was to minimize the disturbance caused by the microstep or roughness to the laminar boundary layer, while still ensuring a successful transition. Very interesting results were obtained in the flow control application for the boundary layer transition control, demonstrating a positive effect on the flow unsteadiness in changing the nature of the interaction.
- 12 October 2020
- Published by ASME International in Journal of Fluids Engineering
- Vol. 143 (1)
Passive Reduction of Leakage by Transverse Jet
This article presents investigations of mass flow reduction in a gap above a fin by the air curtain technique. The proposed method uses slots in the fin to generate a bypass flow and to create a fluidic barrier in the gap above the fin. Both numerical and experimental researches were conducted and the air curtain proved to be effective, showing the mass flow reduction up to about 20%. The comparison of numerical simulations and experimental data showed good agreement, and the flow structure details were analyzed based on the numerical results. The analysis shows that the blown air in the gap leads to creation of streamwise vortices. They enforce crosswise nonuniformity of the flow velocity in the gap and downstream, what finally influences on higher dissipation effects and mass flow reduction in the gap.
- 12 October 2020
- Published by ASME International in Journal of Fluids Engineering
- Vol. 143 (1)
Passive Reduction of Leakage by Transverse Jet
This article presents investigations of mass flow reduction in a gap above a fin by the air curtain technique. The proposed method uses slots in the fin to generate a bypass flow and to create a fluidic barrier in the gap above the fin. Both numerical and experimental researches were conducted and the air curtain proved to be effective, showing the mass flow reduction up to about 20%. The comparison of numerical simulations and experimental data showed good agreement, and the flow structure details were analyzed based on the numerical results. The analysis shows that the blown air in the gap leads to creation of streamwise vortices. They enforce crosswise nonuniformity of the flow velocity in the gap and downstream, what finally influences on higher dissipation effects and mass flow reduction in the gap.
- 2 September 2019
- Published by Emerald Publishing in Aircraft Engineering and Aerospace Technology
- Vol. 91 (8) , 1077-1085
Leakage flow analysis in the gas turbine shroud gap
Purpose: The purpose of the study is to measure the mass flow in the flow through the labyrinth seal of the gas turbine and compare it to the results of numerical simulation. Moreover the capability of two turbulence models to reflect the phenomenon will be assessed. The studied case will later be used as a reference case for the new, original design of flow control method to limit the leakage flow through the labyrinth seal. Design/methodology/approach: Experimental measurements were conducted, measuring the mass flow and the pressure in the model of the labyrinth seal. It was compared to the results of numerical simulation performed in ANSYS/Fluent commercial code for the same geometry. Findings: The precise machining of parts was identified as crucial for obtaining correct results in the experiment. The model characteristics were documented, allowing for its future use as the reference case for testing the new labyrinth seal geometry. Experimentally validated numerical model of the flow in the labyrinth seal was developed. Research limitations/implications: The research studies the basic case, future research on the case with a new labyrinth seal geometry is planned. Research is conducted on simplified case without rotation and the impact of the turbine main channel. Practical implications: Importance of machining accuracy up to 0.01 mm was found to be important for measuring leakage in small gaps and decision making on the optimal configuration selection. Originality/value: The research is an important step in the development of original modification of the labyrinth seal, resulting in leakage reduction, by serving as a reference case.
- 2 September 2019
- Published by Emerald Publishing in Aircraft Engineering and Aerospace Technology
- Vol. 91 (8) , 1077-1085
Leakage flow analysis in the gas turbine shroud gap
Purpose: The purpose of the study is to measure the mass flow in the flow through the labyrinth seal of the gas turbine and compare it to the results of numerical simulation. Moreover the capability of two turbulence models to reflect the phenomenon will be assessed. The studied case will later be used as a reference case for the new, original design of flow control method to limit the leakage flow through the labyrinth seal. Design/methodology/approach: Experimental measurements were conducted, measuring the mass flow and the pressure in the model of the labyrinth seal. It was compared to the results of numerical simulation performed in ANSYS/Fluent commercial code for the same geometry. Findings: The precise machining of parts was identified as crucial for obtaining correct results in the experiment. The model characteristics were documented, allowing for its future use as the reference case for testing the new labyrinth seal geometry. Experimentally validated numerical model of the flow in the labyrinth seal was developed. Research limitations/implications: The research studies the basic case, future research on the case with a new labyrinth seal geometry is planned. Research is conducted on simplified case without rotation and the impact of the turbine main channel. Practical implications: Importance of machining accuracy up to 0.01 mm was found to be important for measuring leakage in small gaps and decision making on the optimal configuration selection. Originality/value: The research is an important step in the development of original modification of the labyrinth seal, resulting in leakage reduction, by serving as a reference case.
- Open Access
- 23 October 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1101 (1) , 012012
Leakage flow reduction in different configuration of labyrinth seal on a turbine blade tip
- 23 October 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1101 (1) , 012012
Open AccessLeakage flow reduction in different configuration of labyrinth seal on a turbine blade tip