Zixiao Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zixiao Wang has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Zhiyong Liu
School of Civil Engineering, Yantai University, Yantai 264005, China
6 shared publications - Aming Xie
School of Safety Science and Engineering Nanjing University of Science and Technology Nanjing P. R. China
5 shared publications Ning Song
Graduate Student, School of Civil Engineering, Yantai Univ., Yantai 264005, China
3 shared publications- Weizheng Shi
School of Safety Science and Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
3 shared publications - Qingliang Yu
Department of the Built Environment, Eindhoven University of Technology, Eindhoven, The Netherlands
2 shared publications Shuxin Deng
2 shared publications
Latest Publications
- Open Access
- 16 August 2026
- Published by Elsevier in SSRN Electronic Journal
Design of an ultra-broadband ionic liquid-based metamaterial absorber via hexagonal split-ring resonators
In this work, we present an ultra-broadband metamaterial absorber based on an ionic liquid and a hexagonal split-ring resonator (SRR) architecture, whose design is optimized via a genetic algorithm (GA). The absorber consists of a 3D-printed polylactic acid (PLA) shell encapsulating the ionic liquid OMIM[N(CN)₂]. Through the synergistic combination of the strong dielectric loss inherent to the ionic liquid and the multi-mode resonance behavior of the hexagonal SRR, the proposed structure achieves an effective absorption bandwidth (EAB) from 5.42 to 40 GHz, corresponding to a remarkable relative bandwidth of 152.3%. The underlying absorption mechanism is comprehensively interpreted through impedance matching analysis, Smith chart representations, and electromagnetic field distribution mappings. Experimental results are found to be in good agreement with numerical simulations, thereby substantiating the design's reliability. Overall, this work offers a promising pathway for the development of ultra-broadband metamaterial absorbers with extended low-frequency performance, leveraging the synergetic integration of ionic liquids, engineered structural topologies, and intelligent optimization strategies.
- 16 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDesign of an ultra-broadband ionic liquid-based metamaterial absorber via hexagonal split-ring resonators
In this work, we present an ultra-broadband metamaterial absorber based on an ionic liquid and a hexagonal split-ring resonator (SRR) architecture, whose design is optimized via a genetic algorithm (GA). The absorber consists of a 3D-printed polylactic acid (PLA) shell encapsulating the ionic liquid OMIM[N(CN)₂]. Through the synergistic combination of the strong dielectric loss inherent to the ionic liquid and the multi-mode resonance behavior of the hexagonal SRR, the proposed structure achieves an effective absorption bandwidth (EAB) from 5.42 to 40 GHz, corresponding to a remarkable relative bandwidth of 152.3%. The underlying absorption mechanism is comprehensively interpreted through impedance matching analysis, Smith chart representations, and electromagnetic field distribution mappings. Experimental results are found to be in good agreement with numerical simulations, thereby substantiating the design's reliability. Overall, this work offers a promising pathway for the development of ultra-broadband metamaterial absorbers with extended low-frequency performance, leveraging the synergetic integration of ionic liquids, engineered structural topologies, and intelligent optimization strategies.
- Open Access
The Regulating Effects of Ice-Templated Directional Microchannels on Surface Micro-Ceramicization Strengthening of Cement Paste Containing TiB2
Cementitious materials prepared by the ice-templating method appear to have difficulty simultaneously possessing good mechanical properties and an oriented microstructure with microchannels. Surface micro-ceramicization of TiB2 and the decomposed products of cement hydrates at high temperatures can be regarded as in situ solid–solid reactions involving oxygen, thereby enhancing mechanical properties. This study investigates the mechanical property changes in cement paste with different water-to-cement ratios containing 25% TiB2 micron powder before and after high-temperature treatment. Cementitious samples are prepared using both freeze-casting (F-CAST) and regular casting (R-CAST) methods with and without the heating post-treatment. The average compressive strength of samples with a W/C of 0.65 prepared by the freeze-casting method at −60 °C with a heating post-treatment is much larger than that of samples prepared by the regular casting method with and without the same heating process. The freeze-casting process for preparing cementitious composites with TiB2 not only reorders the distribution of water molecules but also redistributes the concentrations of the TiB2 particles and the main hydrates in the frozen samples. Due to the concentration increase near ice crystal channels within the samples, led by the freeze concentration effect, the new products are formed and cover the channel surfaces after high-temperature treatment. This enhances both the overall and internal properties of the cement-based TiB2 composite material. The variation in TiB2 content within the specimens is of paramount importance.
Open AccessThe Regulating Effects of Ice-Templated Directional Microchannels on Surface Micro-Ceramicization Strengthening of Cement Paste Containing TiB2
Cementitious materials prepared by the ice-templating method appear to have difficulty simultaneously possessing good mechanical properties and an oriented microstructure with microchannels. Surface micro-ceramicization of TiB2 and the decomposed products of cement hydrates at high temperatures can be regarded as in situ solid–solid reactions involving oxygen, thereby enhancing mechanical properties. This study investigates the mechanical property changes in cement paste with different water-to-cement ratios containing 25% TiB2 micron powder before and after high-temperature treatment. Cementitious samples are prepared using both freeze-casting (F-CAST) and regular casting (R-CAST) methods with and without the heating post-treatment. The average compressive strength of samples with a W/C of 0.65 prepared by the freeze-casting method at −60 °C with a heating post-treatment is much larger than that of samples prepared by the regular casting method with and without the same heating process. The freeze-casting process for preparing cementitious composites with TiB2 not only reorders the distribution of water molecules but also redistributes the concentrations of the TiB2 particles and the main hydrates in the frozen samples. Due to the concentration increase near ice crystal channels within the samples, led by the freeze concentration effect, the new products are formed and cover the channel surfaces after high-temperature treatment. This enhances both the overall and internal properties of the cement-based TiB2 composite material. The variation in TiB2 content within the specimens is of paramount importance.
- Open Access
Flash Graphene-Modified Portland Cement Paste with Both High Electromagnetic and Mechanical Performances at a Low Percolation Threshold
The contradiction between the threshold values of carbon nanomaterials in cement-based materials for enhancing electrical, magnetic, and mechanical properties appears irreconcilable in previous studies. Reducing the numerical differences of these thresholds of carbon nanomaterials in cement-based materials is a straightforward approach to resolving the predicament. Flash graphene powder (FGP) with varying dosages is used to prepare the modified Portland cement paste in this work. Hydration heat release behaviours and the morphologies of hydrates are significantly impacted due to the unique turbostratic graphene layers. The percolation threshold of FGP in paste approximates its thresholds for enhancing the strength and absorption of electromagnetic waves (EMWs), which is 0.50 wt.% of cement. The compressive and flexural strength values of samples with 0.50 wt.% FGP increased by 59.5% and 22.4%, respectively, compared with the blank sample. The minimum EMWs loss value of the sample with 0.50 wt.% FGP is −12.2 dB with an effective absorption bandwidth value of 7.76 GHz in the EMWs frequency between 2 and 18 GHz. The smaller Portlandite crystals are associated with better conductive and impedance-matching properties, resulting in significantly improved EMWs absorption in the Ku band. This work proposes a possible solution that involves using FGP to replace normal graphene, thereby alleviating the contradiction and reducing the gaps in the graphene thresholds in cement paste and enhancing mechanical and electrical conductivity and EMWs absorption properties.
Open AccessFlash Graphene-Modified Portland Cement Paste with Both High Electromagnetic and Mechanical Performances at a Low Percolation Threshold
The contradiction between the threshold values of carbon nanomaterials in cement-based materials for enhancing electrical, magnetic, and mechanical properties appears irreconcilable in previous studies. Reducing the numerical differences of these thresholds of carbon nanomaterials in cement-based materials is a straightforward approach to resolving the predicament. Flash graphene powder (FGP) with varying dosages is used to prepare the modified Portland cement paste in this work. Hydration heat release behaviours and the morphologies of hydrates are significantly impacted due to the unique turbostratic graphene layers. The percolation threshold of FGP in paste approximates its thresholds for enhancing the strength and absorption of electromagnetic waves (EMWs), which is 0.50 wt.% of cement. The compressive and flexural strength values of samples with 0.50 wt.% FGP increased by 59.5% and 22.4%, respectively, compared with the blank sample. The minimum EMWs loss value of the sample with 0.50 wt.% FGP is −12.2 dB with an effective absorption bandwidth value of 7.76 GHz in the EMWs frequency between 2 and 18 GHz. The smaller Portlandite crystals are associated with better conductive and impedance-matching properties, resulting in significantly improved EMWs absorption in the Ku band. This work proposes a possible solution that involves using FGP to replace normal graphene, thereby alleviating the contradiction and reducing the gaps in the graphene thresholds in cement paste and enhancing mechanical and electrical conductivity and EMWs absorption properties.
- 13 October 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (28) , 59509-59521
Thermal adaptability of surface micro-ceramization induced by TiB2 micron powders on portland cement paste at different elevated temperatures
- 13 October 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (28) , 59509-59521
Thermal adaptability of surface micro-ceramization induced by TiB2 micron powders on portland cement paste at different elevated temperatures
- Open Access
Effects of Quartz Sand on the Electromagnetic Wave Absorption of Cementitious Materials
The roles of dielectric materials in adjusting the electromagnetic wave (EMW) absorption performance of an EMW absorber are as crucial as the EMW absorbents. The commonly used cement-based materials, such as mortar, are typical composites of multiple dielectric materials, such as quartz sand and air in the pores. This study investigates the EMW-absorption performances within the frequency range of 2 GHz to 18 GHz of cement paste and mortar samples with different sand-to-cement ratios (S/C), water-to-cement ratios (W/C), and thicknesses. The bow-frame method is used to measure the EMW reflection loss (RL) curves of slab-like samples. The coaxial method is used to record the electromagnetic parameters of the sample powders, which are also used to calculate the EMW RL curves. The results prove that the EMW-absorption performances of a slab-like mortar sample are monotonically related to the S/C ratio and the actual air volume, which is closely related to the thickness.
Open AccessEffects of Quartz Sand on the Electromagnetic Wave Absorption of Cementitious Materials
The roles of dielectric materials in adjusting the electromagnetic wave (EMW) absorption performance of an EMW absorber are as crucial as the EMW absorbents. The commonly used cement-based materials, such as mortar, are typical composites of multiple dielectric materials, such as quartz sand and air in the pores. This study investigates the EMW-absorption performances within the frequency range of 2 GHz to 18 GHz of cement paste and mortar samples with different sand-to-cement ratios (S/C), water-to-cement ratios (W/C), and thicknesses. The bow-frame method is used to measure the EMW reflection loss (RL) curves of slab-like samples. The coaxial method is used to record the electromagnetic parameters of the sample powders, which are also used to calculate the EMW RL curves. The results prove that the EMW-absorption performances of a slab-like mortar sample are monotonically related to the S/C ratio and the actual air volume, which is closely related to the thickness.
- Open Access
Anticorrosion Property of Alcohol Amine Modified Phosphoric and Tannic Acid Based Rust Converter and Its Waterborne Polymer-Based Paint for Carbon Steel
Four kinds of alcohol amines were tested to improve the anticorrosion performance of the phosphoric and tannic acid (PTA)-based rust converter. The alcohol amine modified PTA rust converters with the optimum mechanical and functional performances were used to prepare the homogeneous single-component waterborne rust conversion-based paint. The mechanical properties and the long-term corrosion resistance of the synthesized rust converter-based paint were investigated. The results show that alcohol amine modified PTA rust converter can convert the rust layer into a thick passivation film with iron tannate and iron phosphate as the main components, significantly improving the corrosion resistance of the carbon steel. The alcohol amine D modified PTA rust converter (RC-D) showed the best anticorrosion and rust conversion performances. The waterborne rust conversion-based paint can convert the rust layer of steel into a blue-black and relatively flat passivation film layer. The waterborne polymer-based paint containing 10 wt.% RC-D significantly improves the long-term corrosion resistance of the rusty steel and the mechanical property of paint.
Open AccessAnticorrosion Property of Alcohol Amine Modified Phosphoric and Tannic Acid Based Rust Converter and Its Waterborne Polymer-Based Paint for Carbon Steel
Four kinds of alcohol amines were tested to improve the anticorrosion performance of the phosphoric and tannic acid (PTA)-based rust converter. The alcohol amine modified PTA rust converters with the optimum mechanical and functional performances were used to prepare the homogeneous single-component waterborne rust conversion-based paint. The mechanical properties and the long-term corrosion resistance of the synthesized rust converter-based paint were investigated. The results show that alcohol amine modified PTA rust converter can convert the rust layer into a thick passivation film with iron tannate and iron phosphate as the main components, significantly improving the corrosion resistance of the carbon steel. The alcohol amine D modified PTA rust converter (RC-D) showed the best anticorrosion and rust conversion performances. The waterborne rust conversion-based paint can convert the rust layer of steel into a blue-black and relatively flat passivation film layer. The waterborne polymer-based paint containing 10 wt.% RC-D significantly improves the long-term corrosion resistance of the rusty steel and the mechanical property of paint.
- Open Access
- 1 December 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 263
Self-cleaning and air purification performance of Portland cement paste with low dosages of nanodispersed TiO2 coatings
- 1 December 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 263
Open AccessSelf-cleaning and air purification performance of Portland cement paste with low dosages of nanodispersed TiO2 coatings
- 1 February 2020
- Published by Elsevier in Journal of Environmental Sciences
- Vol. 88, 59-71
Photocatalytic performance and dispersion stability of nanodispersed TiO2 hydrosol in electrolyte solutions with different cations
- 1 February 2020
- Published by Elsevier in Journal of Environmental Sciences
- Vol. 88, 59-71
Photocatalytic performance and dispersion stability of nanodispersed TiO2 hydrosol in electrolyte solutions with different cations
- 1 September 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (9)
Properties and Characterization on a Novel Aqueous Inhibitor for Inhibiting Alloy Steel Corrosion in Chloride Solution
A novel aqueous penetrating corrosion inhibitor marked PCI-2016 was prepared by using multicompound and chelate-induced techniques for this paper. Adsorption and inhibition behaviors of PCI-2016 in a chloride solution had been investigated. Test results indicated that the PCI-2016 had an excellent inhibition ability and an identified curative effect on the corrosive steel in the chloride solution. Adsorption of PCI-2016 molecules on the steel surface followed the Temkin adsorption isotherm. The scanning electron microscope (SEM), the energy dispersive spectrometer (EDS), and the atomic force microscope (AFM) images showed many small global or columnar substances had accumulated on the steel surface and the elements of N and Zn in corrosion inhibitors were detected on the steel surface. The X-ray photoelectron spectroscopy (XPS) measurements supported the inhibitor particles that were absorbed on the steel surface by chemisorption and a dense film was formed to inhibit the steel corrosion. Mechanism studies indicated that a stable chelate formed between the iron and N-containing polycarboxylate ligands might be responsible for the high inhibiting efficiency of the inhibitor in the chloride solution.
- 1 September 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (9)
Properties and Characterization on a Novel Aqueous Inhibitor for Inhibiting Alloy Steel Corrosion in Chloride Solution
A novel aqueous penetrating corrosion inhibitor marked PCI-2016 was prepared by using multicompound and chelate-induced techniques for this paper. Adsorption and inhibition behaviors of PCI-2016 in a chloride solution had been investigated. Test results indicated that the PCI-2016 had an excellent inhibition ability and an identified curative effect on the corrosive steel in the chloride solution. Adsorption of PCI-2016 molecules on the steel surface followed the Temkin adsorption isotherm. The scanning electron microscope (SEM), the energy dispersive spectrometer (EDS), and the atomic force microscope (AFM) images showed many small global or columnar substances had accumulated on the steel surface and the elements of N and Zn in corrosion inhibitors were detected on the steel surface. The X-ray photoelectron spectroscopy (XPS) measurements supported the inhibitor particles that were absorbed on the steel surface by chemisorption and a dense film was formed to inhibit the steel corrosion. Mechanism studies indicated that a stable chelate formed between the iron and N-containing polycarboxylate ligands might be responsible for the high inhibiting efficiency of the inhibitor in the chloride solution.