Yurii Feshchuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yurii Feshchuk has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Tkachuk
Lutsk National Technical University
1 shared publication - I. L. Shevchuk
Lutsk National Technical University
1 shared publication - Inna Parfentieva
Lutsk National Technical University
1 shared publication Jacek Szczot
Airport Lublin SA
1 shared publicationM. M. Nikoloshin
Ya. S. Podstrigach Institute for Applied Problems of Mechanics and Mathematics, National Academy of Sciences of Ukraine, Lviv, Ukraine
1 shared publicationMykola Dmytriyuk
Lutsk National Technical University
1 shared publication
Latest Publications
- 20 November 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1168, 13-23
Experimental Analysis of the Mechanical Behaviour of 3D Printed Elements: The Role of Fibre Orientation in the Material Structure
The paper investigates the influence of fibre orientation on the mechanical characteristics of PETG plastic products manufactured by FDM printing (Fused Deposition Modelling). Three groups of experimental samples were made with different fibre orientation: along the load axis, perpendicular to it, and at an angle of 45 °. Experimental tensile and compression tests, including the stages of elastic deformation, structure strengthening, and local fracture, were performed to study the mechanical characteristics of the material. It is established that the orientation of the fibres is a determining factor of strength and deformation behaviour of products: samples with fibres along the load axis are characterized by increased plasticity and strength, while the transverse orientation reduces mechanical resistance due to interlayer destruction. Samples with fibre orientation at an angle of 45° demonstrated an optimal combination of strength and deformation capacity. The results of the study confirm the need to consider the fibre orientation when designing PETG plastic products to ensure optimal performance.
- 20 November 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1168, 13-23
Experimental Analysis of the Mechanical Behaviour of 3D Printed Elements: The Role of Fibre Orientation in the Material Structure
The paper investigates the influence of fibre orientation on the mechanical characteristics of PETG plastic products manufactured by FDM printing (Fused Deposition Modelling). Three groups of experimental samples were made with different fibre orientation: along the load axis, perpendicular to it, and at an angle of 45 °. Experimental tensile and compression tests, including the stages of elastic deformation, structure strengthening, and local fracture, were performed to study the mechanical characteristics of the material. It is established that the orientation of the fibres is a determining factor of strength and deformation behaviour of products: samples with fibres along the load axis are characterized by increased plasticity and strength, while the transverse orientation reduces mechanical resistance due to interlayer destruction. Samples with fibre orientation at an angle of 45° demonstrated an optimal combination of strength and deformation capacity. The results of the study confirm the need to consider the fibre orientation when designing PETG plastic products to ensure optimal performance.
- 20 December 2024
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1141, 63-72
Experimental Study of Material Anisotropy Effect for 3D Printing Elements
The article presents the results of experimental studies of the effect of material anisotropy and the presence of tunnel inhomogeneity of 3D-printed elements relative to the direction of compression on the mechanical and strength characteristics of the obtained samples. Test samples made by 3D printing using PETG plastic were used for the research. Research was performed for solid samples and samples with a system of free and reinforced cavities. The results of experimental studies allow us to study the influence of the presence of geometric and structural heterogeneity of bodies on their mechanical and strength characteristics during their 3D printing. Thepeformed studies allow to optimally choose the modes of 3D printing of elements taking into account the anisotropy of the material in order to ensure their maximum strength characteristics. The results of experimental studies confirm the results of numerical calculations [1] obtained on the basis of the finite element method.
- 20 December 2024
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1141, 63-72
Experimental Study of Material Anisotropy Effect for 3D Printing Elements
The article presents the results of experimental studies of the effect of material anisotropy and the presence of tunnel inhomogeneity of 3D-printed elements relative to the direction of compression on the mechanical and strength characteristics of the obtained samples. Test samples made by 3D printing using PETG plastic were used for the research. Research was performed for solid samples and samples with a system of free and reinforced cavities. The results of experimental studies allow us to study the influence of the presence of geometric and structural heterogeneity of bodies on their mechanical and strength characteristics during their 3D printing. Thepeformed studies allow to optimally choose the modes of 3D printing of elements taking into account the anisotropy of the material in order to ensure their maximum strength characteristics. The results of experimental studies confirm the results of numerical calculations [1] obtained on the basis of the finite element method.
- 23 May 2023
- Published by Springer Nature
- p. 221-229
Mechanical Properties of Hybrid Composites Based on Polypropylene Modified with Natural Fillers
- 23 May 2023
- Published by Springer Nature
- p. 221-229
Mechanical Properties of Hybrid Composites Based on Polypropylene Modified with Natural Fillers
- 26 May 2021
- Published by Springer Nature
- p. 602-612
Structure and Properties of Surface Bandage Shelves for the Gas Turbine Engine’s Blades
- 26 May 2021
- Published by Springer Nature
- p. 602-612
Structure and Properties of Surface Bandage Shelves for the Gas Turbine Engine’s Blades
- 22 September 2020
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 864, 292-302
High-Copper Cast Irons for the Products of Tribotechnical Applied
The paper presents the results of the development of a special group of cast composite materials based on nodular cast irons. The alloys were based on alloying cast iron with copper in amounts that exceed its solubility in liquid Fe-C-Si systems (Cu>6 wt.%). A new component is obtained in the structure of castings in the form of a complex mixture based on the Cu-phase. Inclusions are relatively large (up to 200 μm) and globular in shape, with a uniform allocation in the volume of the castings. This favorably distinguishes the obtained alloys from the known cast irons and gives them high antifriction properties. With isothermal hardening, it is possible to obtain the lowest values of wear for structures of lower bainite. Developed cast composite materials are recommended to be used as tribotechnical materials working in conditions of poor lubrication and corrosion.
- 22 September 2020
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 864, 292-302
High-Copper Cast Irons for the Products of Tribotechnical Applied
The paper presents the results of the development of a special group of cast composite materials based on nodular cast irons. The alloys were based on alloying cast iron with copper in amounts that exceed its solubility in liquid Fe-C-Si systems (Cu>6 wt.%). A new component is obtained in the structure of castings in the form of a complex mixture based on the Cu-phase. Inclusions are relatively large (up to 200 μm) and globular in shape, with a uniform allocation in the volume of the castings. This favorably distinguishes the obtained alloys from the known cast irons and gives them high antifriction properties. With isothermal hardening, it is possible to obtain the lowest values of wear for structures of lower bainite. Developed cast composite materials are recommended to be used as tribotechnical materials working in conditions of poor lubrication and corrosion.
- 1 April 2009
- Published by Springer Nature in International Applied Mechanics
- Vol. 45 (4) , 437-442
Limit equilibrium of a transversely isotropic spherical shell with two surface cracks
- 1 April 2009
- Published by Springer Nature in International Applied Mechanics
- Vol. 45 (4) , 437-442
Limit equilibrium of a transversely isotropic spherical shell with two surface cracks