Kemal Yaman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kemal Yaman has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Atak
Department of Industrial Design, Faculty of Architecture and Design, OSTIM Technical University, Ankara 06374, Turkey
1 shared publication Ali Özgedik
1 shared publication- Fatih Koşar
Depth. Of Mechanical Systems, Research and Development Institute, Turkish
1 shared publication Ferhat Akyürek
The Scientific and Technical Research Council of Turkey-Defense Industries Research and Development Institute (TUBİTAK-SAGE)
1 shared publicationKamuran Kamil Yeşi̇lkaya
Tübitak Sage
1 shared publication- Mehmet Fatih Öktem
Ankara Yildirim Beyazit Universitesi
1 shared publication
Latest Publications
- 20 July 2026
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 41 (2) , 1299-1314
17-4PH paslanmaz çeliğin oyuk korozyon davranışının fraktal boyut ve Shannon entropi ile karakterizasyonu
Bu çalışma, sulu klorür çözeltisinde farklı sertlik seviyelerine kadar termal olarak yaşlandırılmış 17-4 PH paslanmaz çelik alaşımlarında oyuk korozyonu oluşumu ve gelişim davranışını incelemektedir. Çözeltide %10 oranında klorür ve %30 oranında hidrojen peroksit bulunmaktadır ve numuneler sabit oda sıcaklığında tutulurken farklı sürelerde bu aşındırıcı ortama maruz bırakılmıştır. Çalışmada, farklı sertlik düzeylerine sahip numunelerde maruz kalma süresinin etkileri ve oyuk gelişimi araştırılmıştır. Bu çalışmada kullanılan yöntemler arasında ağırlık kaybı ölçümleri, makro gözlemler, taramalı elektron mikroskobu (SEM) analizleri, elektrokimyasal testler, fraktal ve shannon entropi değerlendirmeleri yer almaktadır. Oyuk korozyon potansiyeli, aşınma süresi boyunca potansiyodinamik polarizasyon yöntemiyle izlenmiştir. Elde edilen bulgular, oyuk korozyonu potansiyelinin yaşlandırma sıcaklığına bağlı olarak değiştiğini ve malzemenin sertliğiyle ilişkili olduğunu göstermektedir. Aşınma sonucunda elde edilen numuneler üzerinde yapılan görüntü işleme ve fraktal boyut analizlerinden elde edilen bilgilere dayanarak oyuk korozyonun aşınma süresi boyunca oluşum ve gelişim davranışları incelenmiştir.
- 20 July 2026
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 41 (2) , 1299-1314
17-4PH paslanmaz çeliğin oyuk korozyon davranışının fraktal boyut ve Shannon entropi ile karakterizasyonu
Bu çalışma, sulu klorür çözeltisinde farklı sertlik seviyelerine kadar termal olarak yaşlandırılmış 17-4 PH paslanmaz çelik alaşımlarında oyuk korozyonu oluşumu ve gelişim davranışını incelemektedir. Çözeltide %10 oranında klorür ve %30 oranında hidrojen peroksit bulunmaktadır ve numuneler sabit oda sıcaklığında tutulurken farklı sürelerde bu aşındırıcı ortama maruz bırakılmıştır. Çalışmada, farklı sertlik düzeylerine sahip numunelerde maruz kalma süresinin etkileri ve oyuk gelişimi araştırılmıştır. Bu çalışmada kullanılan yöntemler arasında ağırlık kaybı ölçümleri, makro gözlemler, taramalı elektron mikroskobu (SEM) analizleri, elektrokimyasal testler, fraktal ve shannon entropi değerlendirmeleri yer almaktadır. Oyuk korozyon potansiyeli, aşınma süresi boyunca potansiyodinamik polarizasyon yöntemiyle izlenmiştir. Elde edilen bulgular, oyuk korozyonu potansiyelinin yaşlandırma sıcaklığına bağlı olarak değiştiğini ve malzemenin sertliğiyle ilişkili olduğunu göstermektedir. Aşınma sonucunda elde edilen numuneler üzerinde yapılan görüntü işleme ve fraktal boyut analizlerinden elde edilen bilgilere dayanarak oyuk korozyonun aşınma süresi boyunca oluşum ve gelişim davranışları incelenmiştir.
- 31 December 2025
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 9 (4) , 491-499
Anti-Slip and Armor Effective Skid Chain with a Novel Tension Mechanism
Safe driving on snowy and icy roads remains a critical engineering challenge. Existing anti-skid systems are often impractical, time-consuming, and not user-friendly in emergency situations. In this study, a next-generation solution called the Octopus Skid Chain (OSC) is presented, designed for easy installation and removal without requiring professional expertise. The system uses a tensioning wire rope mechanism, and octopus-like arms with fingers that grip the inner sidewall of the tire, enabling secure and slip-free motion over harsh winter terrain. A variant of this system, named the Tire Protection System (TKS), uses the same tension mechanism but is modified to serve as a protective shield against external threats such as landmines and bullets. Both systems feature a modular design and can be adapted to various vehicle types, offering multifunctionality in both civilian and military contexts. Finite element analysis of the TKS system under a 500 N static tensile load showed a maximum equivalent stress of approximately 400 MPa on the wire rope and total deformation below 0.7 mm, confirming the system’s structural safety and performance. The proposed OSC and TKS systems provide innovative, high-efficiency solutions for vehicle traction and tire protection in challenging terrain conditions, combining ease of use, adaptability, and mechanical reliability.
- 31 December 2025
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 9 (4) , 491-499
Anti-Slip and Armor Effective Skid Chain with a Novel Tension Mechanism
Safe driving on snowy and icy roads remains a critical engineering challenge. Existing anti-skid systems are often impractical, time-consuming, and not user-friendly in emergency situations. In this study, a next-generation solution called the Octopus Skid Chain (OSC) is presented, designed for easy installation and removal without requiring professional expertise. The system uses a tensioning wire rope mechanism, and octopus-like arms with fingers that grip the inner sidewall of the tire, enabling secure and slip-free motion over harsh winter terrain. A variant of this system, named the Tire Protection System (TKS), uses the same tension mechanism but is modified to serve as a protective shield against external threats such as landmines and bullets. Both systems feature a modular design and can be adapted to various vehicle types, offering multifunctionality in both civilian and military contexts. Finite element analysis of the TKS system under a 500 N static tensile load showed a maximum equivalent stress of approximately 400 MPa on the wire rope and total deformation below 0.7 mm, confirming the system’s structural safety and performance. The proposed OSC and TKS systems provide innovative, high-efficiency solutions for vehicle traction and tire protection in challenging terrain conditions, combining ease of use, adaptability, and mechanical reliability.
- Open Access
- 12 December 2024
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 27 (6) , 2325-2333
Investigatıon of the Effect of Built-Up Edge on Chip Morphology at the Cutting Edge During Turning Operation
Investigating the mechanism of Built-Up Edge (BUE) formation, which increases tool wear and leads to a decrease in surface quality and tool life, is a critical aspect in engineering applications. A detailed examination of this mechanism holds great importance for extending tool life, reducing workpiece surface roughness, and ultimately lowering tool and production costs. Currently, theoretical, experimental, and numerical studies on this formation mechanism are still ongoing. In this research, the effects of cutting speed on the BUE formation mechanism and the resulting chip morphology were examined in detail, while keeping the cutting depth and feed rate constant. Experimental studies have shown that cutting speed directly influences the formation of BUE and the resulting chip morphology. The extent of this effect, along with details related to chip morphology and BUE formation, was analyzed by comparing scanning electron microscope images. Additionally, the relationship between cutting force values read from the machine monitor during cutting and cutting speed was also investigated. This research highlights the potential to achieve a longer tool life, high-quality workpiece surfaces, and cost-effective production through the optimization of parameters in the workpiece machining process
- 12 December 2024
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 27 (6) , 2325-2333
Open AccessInvestigatıon of the Effect of Built-Up Edge on Chip Morphology at the Cutting Edge During Turning Operation
Investigating the mechanism of Built-Up Edge (BUE) formation, which increases tool wear and leads to a decrease in surface quality and tool life, is a critical aspect in engineering applications. A detailed examination of this mechanism holds great importance for extending tool life, reducing workpiece surface roughness, and ultimately lowering tool and production costs. Currently, theoretical, experimental, and numerical studies on this formation mechanism are still ongoing. In this research, the effects of cutting speed on the BUE formation mechanism and the resulting chip morphology were examined in detail, while keeping the cutting depth and feed rate constant. Experimental studies have shown that cutting speed directly influences the formation of BUE and the resulting chip morphology. The extent of this effect, along with details related to chip morphology and BUE formation, was analyzed by comparing scanning electron microscope images. Additionally, the relationship between cutting force values read from the machine monitor during cutting and cutting speed was also investigated. This research highlights the potential to achieve a longer tool life, high-quality workpiece surfaces, and cost-effective production through the optimization of parameters in the workpiece machining process
- Open Access
- 12 December 2024
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 27 (6) , 2105-2116
Design and Testing of A Cost-Effective Active Force Sensor With Servo Control
In this work, the computerized control of a hydraulic system with analog characteristics is examined, and within this scope, a novel force sensor is designed. The system consists of two main structures: an analog subsystem comprising a four-way servo valve, hydraulic piston, servo amplifier, and the designed force sensor, and a digitizing subsystem responsible for comparison and control, composed of a desktop computer. Throughout this work, a cost-effective force sensor was designed by integrating a compression spring, guides, a support frame and a linear variable differential transformer (LVDT). In this integrated system, the force applied at a specific magnitude and frequency from an external force measurement and feedback unit is converted into electrical signals by horizontal motion of the LVDT core. These electrical signals from the force sensor are digitized and fed back to the computer and data acquisition card. The digitized data transferred to the software developed in this study continuously compare with the reference data, enabling position-dependent force control. Experiments conducted with the force sensor placed between two hydraulic pistons controlled by a servo valve revealed that it caused the pistons to move right and left, providing the desired control of the system with the reference force input. The system was observed to operate much more stably, especially for high-frequency signal inputs.
- 12 December 2024
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 27 (6) , 2105-2116
Open AccessDesign and Testing of A Cost-Effective Active Force Sensor With Servo Control
In this work, the computerized control of a hydraulic system with analog characteristics is examined, and within this scope, a novel force sensor is designed. The system consists of two main structures: an analog subsystem comprising a four-way servo valve, hydraulic piston, servo amplifier, and the designed force sensor, and a digitizing subsystem responsible for comparison and control, composed of a desktop computer. Throughout this work, a cost-effective force sensor was designed by integrating a compression spring, guides, a support frame and a linear variable differential transformer (LVDT). In this integrated system, the force applied at a specific magnitude and frequency from an external force measurement and feedback unit is converted into electrical signals by horizontal motion of the LVDT core. These electrical signals from the force sensor are digitized and fed back to the computer and data acquisition card. The digitized data transferred to the software developed in this study continuously compare with the reference data, enabling position-dependent force control. Experiments conducted with the force sensor placed between two hydraulic pistons controlled by a servo valve revealed that it caused the pistons to move right and left, providing the desired control of the system with the reference force input. The system was observed to operate much more stably, especially for high-frequency signal inputs.
- 25 March 2021
- Published by Springer Nature in Polymer Bulletin
- Vol. 79 (5) , 3309-3332
Fractal characterization of electrical conductivity and mechanical properties of copper particulate polyester matrix composites using image processing
- 25 March 2021
- Published by Springer Nature in Polymer Bulletin
- Vol. 79 (5) , 3309-3332
Fractal characterization of electrical conductivity and mechanical properties of copper particulate polyester matrix composites using image processing
- Open Access
- 1 February 2020
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 70 (1) , 23-34
Location Size and Orientation Effect of Semi elliptical Surface Crack on the Fracture of a Type 3 Composite Pressure Vessel using J integral Method
In this study, structural design and analysis of a type-3 composite over wrapped pressure vessel used in a military satellite propulsion system is presented. The aim is to design a composite tank lighter than all metal fuel tanks having the same volume. Moreover, necessary design stages have been revealed for similar composite over wrapped pressure vessels. ANSYS® is used to perform the stress-strain analysis of both metal and composite parts, to determine the optimum winding angle, tank Autofrettage and fracture characteristic for the metal liner considering the crack morphology. Tsai-Hill, Tsai-Wu and Hashin theories have been implemented to investigate the various failure modes of the composite vessel. Location, size and orientation angle of semi-elliptical surface crack has a pronounced effect on fracture characteristic of the liner. In fracture investigation J-integral method is used. It is foreseen that even in the most critical crack, the crack will not propagate and there will be no burst in the tank for proposed loading conditions. Numerical results are good agreement with the experimental results.
- 1 February 2020
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 70 (1) , 23-34
Open AccessLocation Size and Orientation Effect of Semi elliptical Surface Crack on the Fracture of a Type 3 Composite Pressure Vessel using J integral Method
In this study, structural design and analysis of a type-3 composite over wrapped pressure vessel used in a military satellite propulsion system is presented. The aim is to design a composite tank lighter than all metal fuel tanks having the same volume. Moreover, necessary design stages have been revealed for similar composite over wrapped pressure vessels. ANSYS® is used to perform the stress-strain analysis of both metal and composite parts, to determine the optimum winding angle, tank Autofrettage and fracture characteristic for the metal liner considering the crack morphology. Tsai-Hill, Tsai-Wu and Hashin theories have been implemented to investigate the various failure modes of the composite vessel. Location, size and orientation angle of semi-elliptical surface crack has a pronounced effect on fracture characteristic of the liner. In fracture investigation J-integral method is used. It is foreseen that even in the most critical crack, the crack will not propagate and there will be no burst in the tank for proposed loading conditions. Numerical results are good agreement with the experimental results.
- 28 August 2019
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 25 (4) , 326-334
Heat partition effect on cutting tool morphology in orthogonal metal cutting using finite element method
It is widely accepted that heat partition and temperature distribution for metal cutting process have a significant effect on the morphological features of the cutting tool. Tool life and cutting accuracy are considerably affected by temperature distribution and heat transfer mechanisms on the tool. When a finite elements model is accurately generated, an understanding of heat partition into the cutting tool without performing experiments can be gained. This study has been completed with the use of uncoated and coated tools in order to predetermine heat partition value entering the cutting tool. In terms of coated tools, tool coating was investigated to assess its effects on heat partition. Finite Element Method was mainly used in combination with the previously generated experimental data in literature. Three-dimensional uncoated and coated models were created and made compatible with finite element modeling software to be able to perform thermal analyses of the cutting process. Finite element transient and steady-state temperature values were calculated and hence the heat intensity value for the cutting tool was determined.
- 28 August 2019
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 25 (4) , 326-334
Heat partition effect on cutting tool morphology in orthogonal metal cutting using finite element method
It is widely accepted that heat partition and temperature distribution for metal cutting process have a significant effect on the morphological features of the cutting tool. Tool life and cutting accuracy are considerably affected by temperature distribution and heat transfer mechanisms on the tool. When a finite elements model is accurately generated, an understanding of heat partition into the cutting tool without performing experiments can be gained. This study has been completed with the use of uncoated and coated tools in order to predetermine heat partition value entering the cutting tool. In terms of coated tools, tool coating was investigated to assess its effects on heat partition. Finite Element Method was mainly used in combination with the previously generated experimental data in literature. Three-dimensional uncoated and coated models were created and made compatible with finite element modeling software to be able to perform thermal analyses of the cutting process. Finite element transient and steady-state temperature values were calculated and hence the heat intensity value for the cutting tool was determined.
- Open Access
- 24 July 2018
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2018, 1
Corrigendum to “Subsonic Flutter of Cantilever Rectangular PC Plate Structure”
- 24 July 2018
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2018, 1
Open AccessCorrigendum to “Subsonic Flutter of Cantilever Rectangular PC Plate Structure”
- Open Access
- 29 April 2018
- Published by Wiley in International Journal of Polymer Science
- Vol. 2018, 1-10
Thermal and Electrical Conductivity of Unsaturated Polyester Resin Filled with Copper Filler Composites
Thermal and electrical conductivity of unsaturated polyester resin with copper filler composite material are investigated both theoretically and experimentally. In the experiments, polyester matrix is combined with dendrite-shape copper to determine the effects of both filler size and content on thermal and electrical conductivity, respectively. It is observed that the increase in the concentration causes the thermal and electrical conductivity of composite mixture to grow up. It has also been observed that the both thermal and electrical conductivity increase with increasing filler particle size.
- 29 April 2018
- Published by Wiley in International Journal of Polymer Science
- Vol. 2018, 1-10
Open AccessThermal and Electrical Conductivity of Unsaturated Polyester Resin Filled with Copper Filler Composites
Thermal and electrical conductivity of unsaturated polyester resin with copper filler composite material are investigated both theoretically and experimentally. In the experiments, polyester matrix is combined with dendrite-shape copper to determine the effects of both filler size and content on thermal and electrical conductivity, respectively. It is observed that the increase in the concentration causes the thermal and electrical conductivity of composite mixture to grow up. It has also been observed that the both thermal and electrical conductivity increase with increasing filler particle size.