CHCharles R. Herd

Charles R. Herd

*This is an algorithmically generated author record based on publicly available information.

Charles R. Herd has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    New Insights on Fatigue Crack Growth of Reinforced Natural Rubber

    by William Amoako Kyei-Manu, Lewis B. Tunnicliffe, Charles R. Herd, Keizo Akutagawa, James J. C. Busfield

    The fatigue crack growth of natural rubber reinforced with various grades of carbon black has been studied across a wide range of tearing energies. Carbon blacks differ significantly in structure and surface area, influencing the mechanical and dynamic properties of the compounds. High-structure carbon black compounds exhibit an abrupt and significant step change in crack growth rate. Above the point of this step change, the different carbon black compounds have similar crack growth rates. Prior to this step change, high-structure carbon black compounds show a better crack growth resistance of up to two orders of magnitude compared to low-structure carbon black compounds. These step changes are attributed to strain-induced crystallisation effects. Before the step change, high-structure carbon black compounds nucleate and grow enough crystals at the crack tip to suppress crack growth. Above the step change, the crack tip velocity is too rapid for substantial strain-induced crystallisation to occur, as it is a time-dependent phenomenon. The step change aligns with the crack tip velocity where strain-induced crystallisation is reportedly absent. Understanding these step changes in crack growth can help rubber compounders design materials with improved crack growth resistance, leading to more durable components.


  • Open Access

    The Influence of Colloidal Properties of Carbon Black on Static and Dynamic Mechanical Properties of Natural Rubber

    by William Amoako Kyei-Manu, Charles R. Herd, Mahatab Chowdhury, James J. C. Busfield, Lewis B. Tunnicliffe

    The influence of carbon black (CB) structure and surface area on key rubber properties such as monotonic stress-strain, cyclic stress–strain, and dynamic mechanical behaviors are investigated in this paper. Natural rubber compounds containing eight different CBs were examined at equivalent particulate volume fractions. The CBs varied in their surface area and structure properties according to a wide experimental design space, allowing robust correlations to the experimental data sets to be extracted. Carbon black structure plays a dominant role in defining the monotonic stress–strain properties (e.g., secant moduli) of the compounds. In line with the previous literature, this is primarily due to strain amplification and occluded rubber mechanisms. For cyclic stress–strain properties, which include the Mullins effect and cyclic softening, the observed mechanical hysteresis is strongly correlated with carbon black structure, which implies that hysteretic energy dissipation at medium to large strain values is isolated in the rubber matrix and arises due to matrix overstrain effects. Under small to medium dynamic strain conditions, classical strain dependence of viscoelastic moduli is observed (the Payne effect), the magnitude of which varies dramatically and systematically depending on the colloidal properties of the CB. At low strain amplitudes, both CB structure and surface area are positively correlated to the complex moduli. Beyond ~2% strain amplitude the effect of surface area vanishes, while structure plays an increasing and eventually dominant role in defining the complex modulus. This transition in colloidal correlations reflects the transition in stiffening mechanisms from flexing of rigid percolated particle networks at low strains to strain amplification at medium to high strains. By rescaling the dynamic mechanical data sets to peak dynamic stress and peak strain energy density, the influence of CB colloidal properties on compound hysteresis under strain, stress, and strain energy density control can be estimated. This has considerable significance for materials selection in rubber product development.


  • Open Access

    Effect of Fuel Composition on Carbon Black Formation Pathways

    by Madhu Singh, Akshay Gharpure, Randy L. Vander Wal, James Kollar, Charles R. Herd

    Differences in lamellae length, stacking, and particularly a difference in the core-to-shell radial structure are observed for carbon blacks produced using different feedstocks. Carbon black (CB) produced using a coal tar (CT) feedstock formed particles with amorphous cores exhibiting a sharp transition to extended lamellae oriented about the periphery of the particle. In contrast, the carbon black produced from fluidized catalytic cracker (FCC) decant oil as feedstock formed particles with a single nucleated core possess a rather uniform radial transition—reflecting the presence of ordered, concentric lamellae across most of the particle radius. Minimal disorder was observed in the core while the undulations in perimeter lamellae were fewer. Our interpretation for these structural dissimilarities is premised on differences in fuel composition, specifically component classes as found by saturate, aromatic, resin, asphaltene (SARA) analysis. These in turn lead to variation in the relative rates of particle nucleation and particle growth by pyrolysis products, moderated by temperature. Electron energy loss spectroscopy reveals radial variation in the sp2 content between the different feedstocks consistent with observed nanostructures. Collectively these results are interpreted in terms of an offset in nucleation and growth—dependent upon the relative contributions of feedstock aromatic content and pyrolysis processes to particle nucleation and growth. To further test the postulate of different formation conditions for the two carbon blacks pulsed laser annealing was applied. The high temperature heating accentuated the dissimilarities in nanostructure and chemistry—leading to stark dissimilarities. These differences were also manifested by comparing oxidative reactivity.


  • Open Access

    Characterizing Distributions of Tensile Strength and Crack Precursor Size to Evaluate Filler Dispersion Effects and Reliability of Rubber

    by Christopher G. Robertson, Lewis B. Tunnicliffe, Lawrence Maciag, Mark A. Bauman, Kurt Miller, Charles R. Herd, William V. Mars

    Undispersed filler agglomerates or other substantial inclusions/contaminants in rubber can act as large crack precursors that reduce the strength and fatigue lifetime of the material. To demonstrate this, we use tensile strength (stress at break, σb) data from 50 specimens to characterize the failure distribution behavior of carbon black (CB) reinforced styrene-butadiene rubber (SBR) compounds. Poor mixing was simulated by adding a portion of the CB late in the mixing process, and glass beads (microspheres) with 517 μm average diameter were introduced during milling to reproduce the effects of large inclusions. The σb distribution was well described with a simple unimodal Weibull distribution for the control compound, but the tensile strengths of the poor CB dispersion material and the compounds with the glass beads required bimodal Weibull distributions. For the material with the lowest level of glass beads—corresponding to less than one microsphere per test specimen—the bimodal failure distribution spanned a very large range of σb from 13.7 to 22.7 MPa in contrast to the relatively narrow σb distribution for the control from 18.4 to 23.8 MPa. Crack precursor size (c0) distributions were also inferred from the data, and the glass beads introduced c0 values in the 400 μm range compared to about 180 μm for the control. In contrast to σb, critical tearing energy (tear strength) was unaffected by the presence of the CB agglomerates and glass beads, because the strain energy focuses on the pre-cut macroscopic crack in the sample during tear testing rather than on the microscopic crack precursors within the rubber. The glass beads were not detected by conventional filler dispersion measurements using interferometric microscopy, indicating that tensile strength distribution characterization is an important complementary approach for identifying the presence of minor amounts of large inclusions in rubber.