Keith Carver
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Keith Carver has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Fred List Iii
ORNL
11 shared publications - Ryan Dehoff
ORNL
6 shared publications Chase Joslin
4 shared publications- Chase Joslin
ORNL
4 shared publications - Richard Howard
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States). High Flux Isotope Reactor (HFIR)
3 shared publications Thomas Butcher
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
3 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by Office of Scientific and Technical Information (OSTI)
Additively Manufactured Components for Nuclear Power Applications
The AMMT work package for fiscal year 2026 entitled Component Manufacturing and Demonstrations from AM 316 SS includes three activities that showcases qualities of AM 316 SS that are relevant to the domestic nuclear power sector. The design and fabrication of capsules for INL provide a basis for studying the complexities of interaction of AM 316H SS with salt used in molten salt nuclear reactors. Printing compact, high efficiency, defect-free TPMS heat exchangers may enhance the performance of the MARVEL demonstration microreactor. And fabricating AM pre-forms of selected replacement components may shorten the time for repair and maintenance of nuclear reactor subsystems. This report includes details of each of the activities and discusses some opportunities for improvements in component quality and qualification.
- 1 September 2026
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessAdditively Manufactured Components for Nuclear Power Applications
The AMMT work package for fiscal year 2026 entitled Component Manufacturing and Demonstrations from AM 316 SS includes three activities that showcases qualities of AM 316 SS that are relevant to the domestic nuclear power sector. The design and fabrication of capsules for INL provide a basis for studying the complexities of interaction of AM 316H SS with salt used in molten salt nuclear reactors. Printing compact, high efficiency, defect-free TPMS heat exchangers may enhance the performance of the MARVEL demonstration microreactor. And fabricating AM pre-forms of selected replacement components may shorten the time for repair and maintenance of nuclear reactor subsystems. This report includes details of each of the activities and discusses some opportunities for improvements in component quality and qualification.
- Open Access
- 23 July 2026
- Published by Elsevier in SSRN Electronic Journal
Effects of LPBF process parameters on microstructure and mechanical performance of SS316L
Welded sites are well-recognized failure-prone regions in nuclear reactor components due to microstructural heterogeneity, stress and defect accumulation. Near net shape fabrication via laser powder bed fusion printing, provides a promising pathway to minimize components heterogeneity and thus, improve its structural integrity. As such, additive manufacturing (AM) is currently being investigated as the a potential route for manufacturing nuclear reactor components. However, the variability of AM parameters during the printing process introduces some uncertainty to the performance of printed components, making the qualification of these components for highly regulated nuclear applications difficult. Variables such as laser energy and print proximity affect particle spatter generation, increasing porosity and microstructural defects in printed parts. These defects impact the performance of components in reactor environments. To evaluate the induced changes to microstructure and mechanical performance, the current study introduces laser energy variation (low, standard, and high) and spatter variation to laser powder bed fusion printed 316L stainless steel samples. Specifically, we evaluated or measured porosity and hardness by X-ray computed tomography and Vicker’s micro indentation. We show that porosity increases with laser energy and enhanced spatter conditions, while hardness is reduced.
- 23 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffects of LPBF process parameters on microstructure and mechanical performance of SS316L
Welded sites are well-recognized failure-prone regions in nuclear reactor components due to microstructural heterogeneity, stress and defect accumulation. Near net shape fabrication via laser powder bed fusion printing, provides a promising pathway to minimize components heterogeneity and thus, improve its structural integrity. As such, additive manufacturing (AM) is currently being investigated as the a potential route for manufacturing nuclear reactor components. However, the variability of AM parameters during the printing process introduces some uncertainty to the performance of printed components, making the qualification of these components for highly regulated nuclear applications difficult. Variables such as laser energy and print proximity affect particle spatter generation, increasing porosity and microstructural defects in printed parts. These defects impact the performance of components in reactor environments. To evaluate the induced changes to microstructure and mechanical performance, the current study introduces laser energy variation (low, standard, and high) and spatter variation to laser powder bed fusion printed 316L stainless steel samples. Specifically, we evaluated or measured porosity and hardness by X-ray computed tomography and Vicker’s micro indentation. We show that porosity increases with laser energy and enhanced spatter conditions, while hardness is reduced.
- Open Access
- 1 September 2025
- Published by Office of Scientific and Technical Information (OSTI)
Additively Manufactured Pressure Limiting Irradiation Capsule for the High Flux Isotope Reactor
The Advanced Materials and Manufacturing Technologies (AMMT) program previously demonstrated an additively manufactured (AM) irradiation capsule (commonly referred to as a “rabbit”) from 316H stainless steel (SS) for insertion into the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL)1. This report details efforts to design and fabricate an AM pressure limiting structure (PLS) into one of the end caps of a rabbit capsule and qualify it for insertion into HFIR. The PLS includes a thin cylindrical rupture wall, a shield, and internal supports to facilitate printing and ensure mechanical integrity. Its overall dimensions are 9-mm tall and 10-mm in diameter— equivalent to about ¼ of the size of a AAA battery. The PLS maintains safe internal operating pressures for a rabbit capsule while in the reactor. Although this application is specific to HFIR, the approach lends itself to further applications in industrial, aeronautical, advanced space and power generation environments. Several PLS rabbits capsules have been successfully designed, fabricated, pressure tested, and qualified for future insertion into the HFIR for irradiation and post-irradiation evaluation.
- 1 September 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessAdditively Manufactured Pressure Limiting Irradiation Capsule for the High Flux Isotope Reactor
The Advanced Materials and Manufacturing Technologies (AMMT) program previously demonstrated an additively manufactured (AM) irradiation capsule (commonly referred to as a “rabbit”) from 316H stainless steel (SS) for insertion into the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL)1. This report details efforts to design and fabricate an AM pressure limiting structure (PLS) into one of the end caps of a rabbit capsule and qualify it for insertion into HFIR. The PLS includes a thin cylindrical rupture wall, a shield, and internal supports to facilitate printing and ensure mechanical integrity. Its overall dimensions are 9-mm tall and 10-mm in diameter— equivalent to about ¼ of the size of a AAA battery. The PLS maintains safe internal operating pressures for a rabbit capsule while in the reactor. Although this application is specific to HFIR, the approach lends itself to further applications in industrial, aeronautical, advanced space and power generation environments. Several PLS rabbits capsules have been successfully designed, fabricated, pressure tested, and qualified for future insertion into the HFIR for irradiation and post-irradiation evaluation.
- Open Access
- 1 July 2025
- Published by Office of Scientific and Technical Information (OSTI)
Qualification of an Additively Manufactured Irradiation Capsule for the High Flux Isotope Reactor
As part of the Advanced Materials and Manufacturing Technologies (AMMT) Program’s work package Component Manufacturing and Demonstrations from AM 316 SS, irradiation capsules have been additively manufactured (AM) from 316H stainless steel for insertion into the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). The irradiation capsules (commonly referred to as “rabbits”) have been successfully designed, fabricated, pressure tested, qualified, and inserted into the HFIR for irradiation and post-irradiation evaluation. Each rabbit consists of an AM housing and two standard AM end caps. The design is simple and amenable to geometric and material customization. This demonstration helps pave the way for acceptance of AM safety-critical components for nuclear energy applications.
- 1 July 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessQualification of an Additively Manufactured Irradiation Capsule for the High Flux Isotope Reactor
As part of the Advanced Materials and Manufacturing Technologies (AMMT) Program’s work package Component Manufacturing and Demonstrations from AM 316 SS, irradiation capsules have been additively manufactured (AM) from 316H stainless steel for insertion into the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). The irradiation capsules (commonly referred to as “rabbits”) have been successfully designed, fabricated, pressure tested, qualified, and inserted into the HFIR for irradiation and post-irradiation evaluation. Each rabbit consists of an AM housing and two standard AM end caps. The design is simple and amenable to geometric and material customization. This demonstration helps pave the way for acceptance of AM safety-critical components for nuclear energy applications.
- 13 June 2025
- Published by Taylor & Francis in Nuclear Technology
- Vol. 212 (7) , 1794-1803
Design and Demonstration of an Additively Manufactured Integrated Pressure Limiting Structure for Insertion into a Nuclear Research Reactor
- 13 June 2025
- Published by Taylor & Francis in Nuclear Technology
- Vol. 212 (7) , 1794-1803
Design and Demonstration of an Additively Manufactured Integrated Pressure Limiting Structure for Insertion into a Nuclear Research Reactor
- Open Access
- 1 April 2024
- Published by Office of Scientific and Technical Information (OSTI)
Fabrication of a Liner Assembly for the MARVEL Microreactor
A liner assembly for an intermediate heat exchanger within the MARVEL microreactor at Idaho National Laboratory has been fabricated using laser-based additive manufacturing. The liner design includes challenging features such as long thin walls, overhangs, and tight geometric tolerances. Two versions of the liner assembly, one full length and the other shortened, were printed from several materials (316L SS, Inconel 625, and Inconel 718) using four powder-based laser printers (AddUp BeAM Modulo 400 DED, EOS 290M LPBF, GE Concept M2, and GE Concept Xline 2000R LPBF) located at the Manufacturing Demonstration Facility of Oak Ridge National Laboratory. Dimensional accuracy, print time, and powder utilization have been evaluated to help assess the feasibility of these AM approaches to liner fabrication. Based on this assessment, a potentially cost-effective pathway for fabrication has been proposed.
- 1 April 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessFabrication of a Liner Assembly for the MARVEL Microreactor
A liner assembly for an intermediate heat exchanger within the MARVEL microreactor at Idaho National Laboratory has been fabricated using laser-based additive manufacturing. The liner design includes challenging features such as long thin walls, overhangs, and tight geometric tolerances. Two versions of the liner assembly, one full length and the other shortened, were printed from several materials (316L SS, Inconel 625, and Inconel 718) using four powder-based laser printers (AddUp BeAM Modulo 400 DED, EOS 290M LPBF, GE Concept M2, and GE Concept Xline 2000R LPBF) located at the Manufacturing Demonstration Facility of Oak Ridge National Laboratory. Dimensional accuracy, print time, and powder utilization have been evaluated to help assess the feasibility of these AM approaches to liner fabrication. Based on this assessment, a potentially cost-effective pathway for fabrication has been proposed.
- Open Access
- 1 January 2024
- Published by Office of Scientific and Technical Information (OSTI)
Additively Manufacturing Nitinol Shape Memory Alloys for Advanced Actuator Designs
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 January 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessAdditively Manufacturing Nitinol Shape Memory Alloys for Advanced Actuator Designs
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 September 2021
- Published by Office of Scientific and Technical Information (OSTI)
Diagnostic and predictive capabilities of the TCR digital platform
The Transformational Challenge Reactor program is leveraging additive manufacturing technologies to fabricate the nuclear components required to assemble a microreactor core. Compared with traditional manufacturing processes, additive manufacturing allows for direct observation of the interior of the component during manufacturing. This unique capability promises significant possibilities for creating a new paradigm for nuclear component qualification by leveraging in-situ process data. This report describes FY21 efforts to predict material tensile properties based on data collected during the laser powder bed fusion printing process. The primary focus of this report is the test campaign designed to generate the large quantities of training data required to implement artificial intelligence algorithms that can predict these material properties. Preliminary prediction results and a demonstration of the overall data collection, analysis, and visualization pipeline are also provided.
- 1 September 2021
- Published by Office of Scientific and Technical Information (OSTI)
Diagnostic and predictive capabilities of the TCR digital platform
The Transformational Challenge Reactor program is leveraging additive manufacturing technologies to fabricate the nuclear components required to assemble a microreactor core. Compared with traditional manufacturing processes, additive manufacturing allows for direct observation of the interior of the component during manufacturing. This unique capability promises significant possibilities for creating a new paradigm for nuclear component qualification by leveraging in-situ process data. This report describes FY21 efforts to predict material tensile properties based on data collected during the laser powder bed fusion printing process. The primary focus of this report is the test campaign designed to generate the large quantities of training data required to implement artificial intelligence algorithms that can predict these material properties. Preliminary prediction results and a demonstration of the overall data collection, analysis, and visualization pipeline are also provided.
- 1 August 2021
- Published by Office of Scientific and Technical Information (OSTI)
Mechanical Properties of Additively Manufactured 316L Stainless Steel Before and After Neutron Irradiation (FY21)
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 August 2021
- Published by Office of Scientific and Technical Information (OSTI)
Mechanical Properties of Additively Manufactured 316L Stainless Steel Before and After Neutron Irradiation (FY21)
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 August 2021
- Published by Office of Scientific and Technical Information (OSTI)
Embedding Sensors in 3D Printed Metal Structures
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 August 2021
- Published by Office of Scientific and Technical Information (OSTI)
Embedding Sensors in 3D Printed Metal Structures
The U.S. Department of Energy's Office of Scientific and Technical Information