Jéssica Ariane Oliveira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jéssica Ariane Oliveira has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Caue Ribeiro
Embrapa Instrumentação
10 shared publications - André Esteves Nogueira
Department of Chemical Engineering, Federal University of São Carlos (UFSCar), São Carlos 13565-905, Brazil
5 shared publications Luís A.M. Ruotolo
4 shared publications- Elaine Cristina Paris
Brazilian Agricultural Research Corporation, Embrapa Instrumentation
3 shared publications - Gelson Tiago dos Santos Tavares da Silva
Department of Chemical Engineering, Queen's University, Kingston, ON, K7L 3N6, Canada
3 shared publications - Jeferson Almeida Dias
School of Applied Sciences, Metallurgy Laboratory, State University of Campinas, Limeira, Brazil
3 shared publications
Latest Publications
- Open Access
- 2 October 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 101
Engineering TiO2:WO3 heterostructures for photocatalysis application
- 2 October 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 101
Open AccessEngineering TiO2:WO3 heterostructures for photocatalysis application
- Open Access
- 1 December 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (12) , 3268
Preparation and Application of Nb2O5 Nanofibers in CO2 Photoconversion
Increasing global warming due to NO, CO, and CH, is significantly harming ecosystems and life worldwide. One promising methodology is converting pollutants into valuable chemicals via photocatalytic processes (by reusable photocatalysts). In this context, the present work aimed to produce a NbO photocatalyst nanofiber system by electrospinning to convert CO. Based on the collected data, the calcination at 600 C for 2 h resulted in the best condition to obtain nanofibers with homogeneous surfaces and an average diameter of 84 nm. As a result, the NbO nanofibers converted CO mostly into CO and CH, reaching values around 8.5 mol g and 0.55 mol g, respectively.- 1 December 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (12) , 3268
Open AccessPreparation and Application of Nb2O5 Nanofibers in CO2 Photoconversion
Increasing global warming due to NO, CO, and CH, is significantly harming ecosystems and life worldwide. One promising methodology is converting pollutants into valuable chemicals via photocatalytic processes (by reusable photocatalysts). In this context, the present work aimed to produce a NbO photocatalyst nanofiber system by electrospinning to convert CO. Based on the collected data, the calcination at 600 C for 2 h resulted in the best condition to obtain nanofibers with homogeneous surfaces and an average diameter of 84 nm. As a result, the NbO nanofibers converted CO mostly into CO and CH, reaching values around 8.5 mol g and 0.55 mol g, respectively. - 1 January 2021
- Published by Elsevier in Materials Research Bulletin
- Vol. 133
Photocatalytic CO2 reduction over Nb2O5/basic bismuth nitrate nanocomposites
- 1 January 2021
- Published by Elsevier in Materials Research Bulletin
- Vol. 133
Photocatalytic CO2 reduction over Nb2O5/basic bismuth nitrate nanocomposites
- 1 August 2020
- Published by Elsevier in Materials Letters
- Vol. 273
Unveiling the role of peroxo groups in Nb2O5 photocatalytic efficiency under visible light
- 1 August 2020
- Published by Elsevier in Materials Letters
- Vol. 273
Unveiling the role of peroxo groups in Nb2O5 photocatalytic efficiency under visible light
- 27 July 2020
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 3 (8) , 7629-7636
CuO Decoration Controls Nb2O5 Photocatalyst Selectivity in CO2 Reduction
CO2 reforming through photocatalytic processes, to obtain products with high energy value and compatible with the current energy infrastructure, is a compelling strategy to minimize its emission to atmosphere. Among catalysts, Nb2O5 has been studied as a prospective candidate, but its practical application requires significant efforts for improved CO2 photoreduction performance and product selectivity. Thus, we proposed the system CuO:Nb2O5 heterojunction as an alternative, preparing through a solvothermal treatment method. Experimental tools as FESEM, HRTEM, and DRS have been used to analyze microstructural and electronic properties. CuO decoration over Nb2O5 adjusted its selectivity for CO2 reduction to CH4, HCOOH, or H3CCOOH in different contents. An investigation of CO2 photoreduction using different electron donors/scavengers (water, sodium oxalate, and potassium bromate) revealed that its decoration influences local CO production by modifying the selectivity. CO has been confirmed as the primary intermediate for HCOOH and CH3COOH production, and CO2 reduction efficiency increases with low CuO content (2.5% wt), leading to the formation of soluble hydrocarbons and increasing for CH4 in higher amounts (10% wt).
- 27 July 2020
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 3 (8) , 7629-7636
CuO Decoration Controls Nb2O5 Photocatalyst Selectivity in CO2 Reduction
CO2 reforming through photocatalytic processes, to obtain products with high energy value and compatible with the current energy infrastructure, is a compelling strategy to minimize its emission to atmosphere. Among catalysts, Nb2O5 has been studied as a prospective candidate, but its practical application requires significant efforts for improved CO2 photoreduction performance and product selectivity. Thus, we proposed the system CuO:Nb2O5 heterojunction as an alternative, preparing through a solvothermal treatment method. Experimental tools as FESEM, HRTEM, and DRS have been used to analyze microstructural and electronic properties. CuO decoration over Nb2O5 adjusted its selectivity for CO2 reduction to CH4, HCOOH, or H3CCOOH in different contents. An investigation of CO2 photoreduction using different electron donors/scavengers (water, sodium oxalate, and potassium bromate) revealed that its decoration influences local CO production by modifying the selectivity. CO has been confirmed as the primary intermediate for HCOOH and CH3COOH production, and CO2 reduction efficiency increases with low CuO content (2.5% wt), leading to the formation of soluble hydrocarbons and increasing for CH4 in higher amounts (10% wt).
- 1 April 2020
- Published by Elsevier in Catalysis Communications
- Vol. 137
Unveiling CuO role in CO2 photoreduction process – Catalyst or reactant?
- 1 April 2020
- Published by Elsevier in Catalysis Communications
- Vol. 137
Unveiling CuO role in CO2 photoreduction process – Catalyst or reactant?
- 1 August 2019
- Published by Elsevier in Journal of Cleaner Production
- Vol. 229, 956-963
Synthesis of zeolite from sugarcane bagasse fly ash and its application as a low-cost adsorbent to remove heavy metals
- 1 August 2019
- Published by Elsevier in Journal of Cleaner Production
- Vol. 229, 956-963
Synthesis of zeolite from sugarcane bagasse fly ash and its application as a low-cost adsorbent to remove heavy metals
- 1 May 2019
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2019-01 (26) , 1288
Photoactive Basic Bismuth Nitrate/Nb2O5 Nanocomposites
Basic bismuth nitrates (BBN) are generated from the incomplete hydrolysis of bismuth nitrate pentahydrate, it is a n-type semiconductor, and it was initially used as precursor of bismuth oxides and for medical applications. BBN also can be employed as photocatalysts, but usually exhibit low quantum efficiency due to the fast recombination of photogenerated charge carriers. In order to improve their photocatalytic performance, semiconductor composites have been proposed, being niobium pentoxide (Nb2O5) a promising candidate to be coupled with BBN. Hence, two different and promising photoactive nanocomposites (Nb-BBN) of BBN (Bi6O5(OH)3(NO3)5.3H2O and Bi2O2(OH)(NO3)) and Nb2O5 were obtained by the oxidant peroxide method followed by crystallization under mild hydrothermal conditions. Ammonium niobium oxalate and bismuth nitrate were the sources of Nb and Bi, respectively. Hydrogen peroxide was used as oxidant, and deionized water was used to prepare all solutions. Bismuth nitrate in contact with water forms immediately a highly hydrated basic bismuth nitrate precipitate (Bi6O5(OH)3(NO3)5.3H2O), named P-BBN. Hydrogen peroxide (10:1 molar ratio H2O2:M, M = Bi + Nb) and ammonium niobium oxalate (3:1 molar ratio Bi:Nb) were added into the suspension containing P-BBN, and the synthesis medium was poured in a teflon-lined hydrothermal reactor with autogenous pressure to promote the crystallization under two different procedures. The first nanocomposite (Nb-BBN120) was obtained using one single step: heating at 1 °C min-1 up to 120 ºC (maintained for 12 h), with a final pressure ca. 7 atm. The second nanocomposite (Nb-BBN230) was synthesized using three consecutive steps: 1) heating at 4 °C min-1 up to 150 ºC, with a final pressure ca. 10 atm; 2) heating at 2 °C min-1 up to 200 ºC, with a final pressure ca. 20 atm; and 3) heating at 1 °C min-1 up to 230 ºC (maintained for 12 h), with a final pressure ca. 31 atm. The photocatalytic performance was evaluated, under ultraviolet irradiation at room temperature, towards the discoloration of an aqueous solution of 10 mg L-1 rhodamine B (RhB) using 10 mL of a suspension containing 10 mg mL-1 photocatalyst. No direct photolysis and adsorption were observed. It was also evaluated the photocatalytic stability of the as-synthesized samples after four consecutives RhB discoloration 2-hour-cycles. XRD patterns revealed that the crystallographic structure of the samples Nb-BBN120 and Nb-BBN230 have a monoclinic Bi6O5(OH)3(NO3)5.3H2O (ICSD 00-2406) and orthorhombic Bi2O2(OH)(NO3) (ICSD 15-4359) phases, respectively. No significant peaks assigned to any Nb2O5 second phase are observed, probably due to its low content and high dispersion or the shielding effect of the strong diffraction signals from BBN. Although any XRD peak has been observed for Nb2O5, its presence in the nanocomposites was confirmed by XRF, ICP-OES, and XPS. The kinetics of RhB photodegradation shows that the hydrothermal treatment in presence of Nb2O5 is of paramount importance to enhance the BBN photoactivity. Although Nb-BBN120 and P-BBN have the same BBN phase, the first one has higher activity than the pristine material. Furthermore, despite of Nb-BBN230 shows the best photocatalytic activity, after performing three reuse cycles there was a loss of ~ 50% of its initial photoactivity, suggesting that the lamellar structure is a key factor on the photocatalyst stability. On the other hand, Nb-BBN120 or even the pristine P-BBN retained their initial photocatalytic activity after reuse. In summary, these novel BBN/Nb2O5 nanocomposites provide new insights into the synthesis of promising BBN photocatalysts for oxidation reactions.
- 1 May 2019
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2019-01 (26) , 1288
Photoactive Basic Bismuth Nitrate/Nb2O5 Nanocomposites
Basic bismuth nitrates (BBN) are generated from the incomplete hydrolysis of bismuth nitrate pentahydrate, it is a n-type semiconductor, and it was initially used as precursor of bismuth oxides and for medical applications. BBN also can be employed as photocatalysts, but usually exhibit low quantum efficiency due to the fast recombination of photogenerated charge carriers. In order to improve their photocatalytic performance, semiconductor composites have been proposed, being niobium pentoxide (Nb2O5) a promising candidate to be coupled with BBN. Hence, two different and promising photoactive nanocomposites (Nb-BBN) of BBN (Bi6O5(OH)3(NO3)5.3H2O and Bi2O2(OH)(NO3)) and Nb2O5 were obtained by the oxidant peroxide method followed by crystallization under mild hydrothermal conditions. Ammonium niobium oxalate and bismuth nitrate were the sources of Nb and Bi, respectively. Hydrogen peroxide was used as oxidant, and deionized water was used to prepare all solutions. Bismuth nitrate in contact with water forms immediately a highly hydrated basic bismuth nitrate precipitate (Bi6O5(OH)3(NO3)5.3H2O), named P-BBN. Hydrogen peroxide (10:1 molar ratio H2O2:M, M = Bi + Nb) and ammonium niobium oxalate (3:1 molar ratio Bi:Nb) were added into the suspension containing P-BBN, and the synthesis medium was poured in a teflon-lined hydrothermal reactor with autogenous pressure to promote the crystallization under two different procedures. The first nanocomposite (Nb-BBN120) was obtained using one single step: heating at 1 °C min-1 up to 120 ºC (maintained for 12 h), with a final pressure ca. 7 atm. The second nanocomposite (Nb-BBN230) was synthesized using three consecutive steps: 1) heating at 4 °C min-1 up to 150 ºC, with a final pressure ca. 10 atm; 2) heating at 2 °C min-1 up to 200 ºC, with a final pressure ca. 20 atm; and 3) heating at 1 °C min-1 up to 230 ºC (maintained for 12 h), with a final pressure ca. 31 atm. The photocatalytic performance was evaluated, under ultraviolet irradiation at room temperature, towards the discoloration of an aqueous solution of 10 mg L-1 rhodamine B (RhB) using 10 mL of a suspension containing 10 mg mL-1 photocatalyst. No direct photolysis and adsorption were observed. It was also evaluated the photocatalytic stability of the as-synthesized samples after four consecutives RhB discoloration 2-hour-cycles. XRD patterns revealed that the crystallographic structure of the samples Nb-BBN120 and Nb-BBN230 have a monoclinic Bi6O5(OH)3(NO3)5.3H2O (ICSD 00-2406) and orthorhombic Bi2O2(OH)(NO3) (ICSD 15-4359) phases, respectively. No significant peaks assigned to any Nb2O5 second phase are observed, probably due to its low content and high dispersion or the shielding effect of the strong diffraction signals from BBN. Although any XRD peak has been observed for Nb2O5, its presence in the nanocomposites was confirmed by XRF, ICP-OES, and XPS. The kinetics of RhB photodegradation shows that the hydrothermal treatment in presence of Nb2O5 is of paramount importance to enhance the BBN photoactivity. Although Nb-BBN120 and P-BBN have the same BBN phase, the first one has higher activity than the pristine material. Furthermore, despite of Nb-BBN230 shows the best photocatalytic activity, after performing three reuse cycles there was a loss of ~ 50% of its initial photoactivity, suggesting that the lamellar structure is a key factor on the photocatalyst stability. On the other hand, Nb-BBN120 or even the pristine P-BBN retained their initial photocatalytic activity after reuse. In summary, these novel BBN/Nb2O5 nanocomposites provide new insights into the synthesis of promising BBN photocatalysts for oxidation reactions.
- 1 April 2019
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 228, 160-167
Zn-doped Nb2O5 photocatalysts driven by visible-light: An experimental and theoretical study
- 1 April 2019
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 228, 160-167
Zn-doped Nb2O5 photocatalysts driven by visible-light: An experimental and theoretical study
- 20 March 2019
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 16 (4) , 1501-1509
Evaluation of the Mn(II) adsorption potential of SiO 2 obtained by different wet chemical methods
This paper describes the development of SiO 2 by 2 different wet chemical methods: polymeric precursor (PP) and sol‐gel (SG). These samples were used as adsorbents of Mn(II) metal ions. Physicochemical characteristics of the 2 adsorbents were established, while zeta potential, Scanning Electron Microscopy, and Brunauer‐Emmett‐Teller (BET) surface area methods were further employed for characterization. Efficiencies of the prepared adsorbents in the adsorption of Mn(II) from aqueous solutions were investigated. The BET surface areas of the prepared adsorbent were 171 and 7 m 2 g −1 for SiO 2 PP and SiO 2 SG, respectively. Optimal adsorption occurred at pH 8.5, 5g L −1 of adsorbent concentration, and 90 minutes of contact time for both adsorbents. The Langmuir and Freundlich isotherms models fitted the experimental data of SiO 2 PP and SiO 2 SG, respectively, and SiO 2 PP showed the highest adsorption capacity due, probably, to its greater specific area.
- 20 March 2019
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 16 (4) , 1501-1509
Evaluation of the Mn(II) adsorption potential of SiO 2 obtained by different wet chemical methods
This paper describes the development of SiO 2 by 2 different wet chemical methods: polymeric precursor (PP) and sol‐gel (SG). These samples were used as adsorbents of Mn(II) metal ions. Physicochemical characteristics of the 2 adsorbents were established, while zeta potential, Scanning Electron Microscopy, and Brunauer‐Emmett‐Teller (BET) surface area methods were further employed for characterization. Efficiencies of the prepared adsorbents in the adsorption of Mn(II) from aqueous solutions were investigated. The BET surface areas of the prepared adsorbent were 171 and 7 m 2 g −1 for SiO 2 PP and SiO 2 SG, respectively. Optimal adsorption occurred at pH 8.5, 5g L −1 of adsorbent concentration, and 90 minutes of contact time for both adsorbents. The Langmuir and Freundlich isotherms models fitted the experimental data of SiO 2 PP and SiO 2 SG, respectively, and SiO 2 PP showed the highest adsorption capacity due, probably, to its greater specific area.