Chuan Yi Foo
Chuan Yi Foo has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Hong Ngee Lim
Functional Nanotechnology Devices Laboratory, Institute of Nanoscience and Nanotechnology, Universiti Putra Malaysia, UPM, Serdang, Malaysia
6 shared publications Nay Ming Huang
4 shared publicationsKhai Yang Tan
School of Energy and Chemical Engineering
3 shared publicationsN.M. Huang
Xiamen Univ Malaysia, Sch Energy & Chem Engn, Sepang, Selangor Darul, Malaysia
3 shared publicationsPoi Sim Khiew
3 shared publicationsA. Pandikumar
2 shared publications
Latest Publications
- 30 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (40) , 56398-56410
Irradiation-Induced Phase-Separated Ionogels with High Ionic Liquid Content for Flexible Supercapacitors
Ionogels with high ionic liquid (IL) content often face a trade-off between achieving high ionic conductivity and maintaining structural integrity and tensile strength. To address this, polymerization-induced phase separation (PIPS) has gained popularity; however, it still suffers from relatively low ionic conductivity due to the increase in IL content, which may result in leakage or ion aggregation. In this work, we demonstrate that controlled irradiation, combined with PIPS, plays a critical role in increasing the IL content of the ionogel for the enhancement of ionic conductivity. By controlling the irradiation, the high IL content ionogel exhibits higher ionic conductivity via increased cross-link density and degree of phase separation, allowing better segregation of ions while also maintaining excellent structural integrity. Notably, the [EMIM][BF4] ionogel fabricated via PIPS exhibits among the highest ionic conductivities reported for [EMIM]-based PIPS ionogels for supercapacitors and sensors under comparable conditions, measuring 5.51 ± 0.31 mS/cm. Furthermore, the practical applicability of the ionogel as a flexible supercapacitor was demonstrated, as the integrated device delivered a high specific capacitance of 103 F/g at a current density of 0.5 A/g along with an energy density of 122 Wh/kg and a power density of 2928 W/kg. The device also exhibited a high capacitance retention (93%) after 30,000 charge-discharge cycles at 1 A/g and was able to maintain stable electrochemical performance even under repeated mechanical deformation. This study demonstrates that irradiation is an effective strategy to further increase the IL content incorporated for higher ionic conductivity and overall better electrochemical performance while maintaining excellent structural integrity under deformation, underscoring its suitability for flexible and wearable devices.
- 30 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (40) , 56398-56410
Irradiation-Induced Phase-Separated Ionogels with High Ionic Liquid Content for Flexible Supercapacitors
Ionogels with high ionic liquid (IL) content often face a trade-off between achieving high ionic conductivity and maintaining structural integrity and tensile strength. To address this, polymerization-induced phase separation (PIPS) has gained popularity; however, it still suffers from relatively low ionic conductivity due to the increase in IL content, which may result in leakage or ion aggregation. In this work, we demonstrate that controlled irradiation, combined with PIPS, plays a critical role in increasing the IL content of the ionogel for the enhancement of ionic conductivity. By controlling the irradiation, the high IL content ionogel exhibits higher ionic conductivity via increased cross-link density and degree of phase separation, allowing better segregation of ions while also maintaining excellent structural integrity. Notably, the [EMIM][BF4] ionogel fabricated via PIPS exhibits among the highest ionic conductivities reported for [EMIM]-based PIPS ionogels for supercapacitors and sensors under comparable conditions, measuring 5.51 ± 0.31 mS/cm. Furthermore, the practical applicability of the ionogel as a flexible supercapacitor was demonstrated, as the integrated device delivered a high specific capacitance of 103 F/g at a current density of 0.5 A/g along with an energy density of 122 Wh/kg and a power density of 2928 W/kg. The device also exhibited a high capacitance retention (93%) after 30,000 charge-discharge cycles at 1 A/g and was able to maintain stable electrochemical performance even under repeated mechanical deformation. This study demonstrates that irradiation is an effective strategy to further increase the IL content incorporated for higher ionic conductivity and overall better electrochemical performance while maintaining excellent structural integrity under deformation, underscoring its suitability for flexible and wearable devices.
- 5 November 2024
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 2 (11) , 2569-2582
Integrating Photothermal-Responsive Shape Memory and Self-Healing Polymers in 4D-Printed Thermally Comfortable Smart Wearables
- 5 November 2024
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 2 (11) , 2569-2582
Integrating Photothermal-Responsive Shape Memory and Self-Healing Polymers in 4D-Printed Thermally Comfortable Smart Wearables
- Open Access
- 2 December 2023
- Published by Elsevier in Next Nanotechnology
- Vol. 5
Facile synthesis of nanostructured sodium and MoS2 incorporated Ni-MOFs with excellent cyclic durability for symmetric supercapacitor application
- 2 December 2023
- Published by Elsevier in Next Nanotechnology
- Vol. 5
Open AccessFacile synthesis of nanostructured sodium and MoS2 incorporated Ni-MOFs with excellent cyclic durability for symmetric supercapacitor application
- 30 June 2023
- Published by Elsevier in Materials Letters
- Vol. 349
Enhancement of electrochemical performance of lithium manganese oxide with graphene for aqueous supercapabattery
- 30 June 2023
- Published by Elsevier in Materials Letters
- Vol. 349
Enhancement of electrochemical performance of lithium manganese oxide with graphene for aqueous supercapabattery
- 1 August 2019
- Published by Elsevier in European Polymer Journal
- Vol. 117, 227-235
Hydrostatic bath synthesis of conductive polypyrrole/reduced graphene oxide aerogel as compression sensor
- 1 August 2019
- Published by Elsevier in European Polymer Journal
- Vol. 117, 227-235
Hydrostatic bath synthesis of conductive polypyrrole/reduced graphene oxide aerogel as compression sensor
- Open Access
- 9 May 2018
- Published by Springer Nature in Scientific Reports
- Vol. 8 (1) , 1-11
Three-Dimensional Printed Electrode and Its Novel Applications in Electronic Devices
Three-dimensional (3D) printing technology provides a novel approach to material fabrication for various applications because of its ability to create low-cost 3D printed platforms. In this study, a printable graphene-based conductive filament was employed to create a range of 3D printed electrodes (3DEs) using a commercial 3D printer. This printing technology provides a simplistic and low-cost approach, which eliminates the need for the ex-situ modification and post-treatment of the product. The conductive nature of the 3DEs provides numerous deposition platforms for electrochemical active nanomaterials such as graphene, polypyrrole, and cadmium sulfide, either through electrochemical or physical approaches. To provide proof-of-concept, these 3DEs were physiochemically and electrochemically evaluated and proficiently fabricated into a supercapacitor and photoelectrochemical sensor. The as-fabricated supercapacitor provided a good capacitance performance, with a specific capacitance of 98.37 Fg−1. In addition, these 3DEs were fabricated into a photoelectrochemical sensing platform. They had a photocurrent response that exceeded expectations (~724.1 μA) and a lower detection limit (0.05 μM) than an ITO/FTO glass electrode. By subsequently modifying the printing material and electrode architecture, this 3D printing approach could provide a facile and rapid manufacturing process for energy devices based on the conceptual design.
- 9 May 2018
- Published by Springer Nature in Scientific Reports
- Vol. 8 (1) , 1-11
Open AccessThree-Dimensional Printed Electrode and Its Novel Applications in Electronic Devices
Three-dimensional (3D) printing technology provides a novel approach to material fabrication for various applications because of its ability to create low-cost 3D printed platforms. In this study, a printable graphene-based conductive filament was employed to create a range of 3D printed electrodes (3DEs) using a commercial 3D printer. This printing technology provides a simplistic and low-cost approach, which eliminates the need for the ex-situ modification and post-treatment of the product. The conductive nature of the 3DEs provides numerous deposition platforms for electrochemical active nanomaterials such as graphene, polypyrrole, and cadmium sulfide, either through electrochemical or physical approaches. To provide proof-of-concept, these 3DEs were physiochemically and electrochemically evaluated and proficiently fabricated into a supercapacitor and photoelectrochemical sensor. The as-fabricated supercapacitor provided a good capacitance performance, with a specific capacitance of 98.37 Fg−1. In addition, these 3DEs were fabricated into a photoelectrochemical sensing platform. They had a photocurrent response that exceeded expectations (~724.1 μA) and a lower detection limit (0.05 μM) than an ITO/FTO glass electrode. By subsequently modifying the printing material and electrode architecture, this 3D printing approach could provide a facile and rapid manufacturing process for energy devices based on the conceptual design.