Sibel Uludag-Demirer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sibel Uludag-Demirer has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Göksel Niyazi Demirer
School of Engineering and Technology, Central Michigan University, Mt. Pleasant, USA
7 shared publications S. Chen
Department of Biological Systems Engineering, Washington State University, Pullman, WA 99163, USA
2 shared publicationsA. R. Bowers
1 shared publicationAlan R. Bowers
Vanderbilt University
1 shared publication- Bilgin Taskin
Ondokuz Mayis University
1 shared publication C. Frear
Department of Biological Systems Engineering, Washington State University, Pullman, WA 99163, USA
1 shared publication
Latest Publications
- 23 October 2012
- Published by Springer Nature in Applied Microbiology and Biotechnology
- Vol. 97 (17) , 7899-7907
The effect of managing nutrients in the performance of anaerobic digesters of municipal wastewater treatment plants
- 23 October 2012
- Published by Springer Nature in Applied Microbiology and Biotechnology
- Vol. 97 (17) , 7899-7907
The effect of managing nutrients in the performance of anaerobic digesters of municipal wastewater treatment plants
- 1 December 2009
- Published by Wiley in Water Environment Research
- Vol. 81 (12) , 2447-2454
Modification of a Conventional Anaerobic Digester for Improving the Effluent and Sludge Characteristics
The aim of this study was to enrich the composition of anaerobic digester sludge in terms of nitrogen and phosphorus by struvite (MgNH4PO4) formation. Waste activated sludge was anaerobically digested in batch reactors under the conditions that the minimum stoichiometric requirement for struvite formation was satisfied in all reactors. For this purpose, different amounts of magnesium (Mg2+) and phosphate (PO43−) ions were added initially to the batch reactors. The results showed the effects of adding Mg2+ and PO43− ions on the performance of anaerobic digestion and on the amounts of ammonium (NH4+) and PO43− ions released during digestion. The results indicated that the performance of the anaerobic digestion in chemical oxygen demand removal changed between −4.0% and 15.4% for a Mg2+ concentration range of 277.2 to 529.3 mg/L and a PO43− concentration range of 377.4 to 2372.4 mg/L. There was an increase in the concentration of NH4+ in all reactors during digestion, but the extent of concentration increase could be controlled by increasing the initial concentrations of Mg2+ and PO43−. The maximum removal of NH4+ ions (33.7%) was observed in the reactor dosed initially by Mg2+ and PO43− concentrations of 467.2 and 2123.3 mg/L, respectively. The concentration of PO43− ion was lower than its initial concentration in all reactors, indicating considerable fixation of PO43− as it was released, by struvite and other solid species formation. The decrease in the concentration of Mg2+ ions similar to PO43− was accepted as evidence for the formation of solid species composed of Mg2+ and PO43, in addition to struvite.
- 1 December 2009
- Published by Wiley in Water Environment Research
- Vol. 81 (12) , 2447-2454
Modification of a Conventional Anaerobic Digester for Improving the Effluent and Sludge Characteristics
The aim of this study was to enrich the composition of anaerobic digester sludge in terms of nitrogen and phosphorus by struvite (MgNH4PO4) formation. Waste activated sludge was anaerobically digested in batch reactors under the conditions that the minimum stoichiometric requirement for struvite formation was satisfied in all reactors. For this purpose, different amounts of magnesium (Mg2+) and phosphate (PO43−) ions were added initially to the batch reactors. The results showed the effects of adding Mg2+ and PO43− ions on the performance of anaerobic digestion and on the amounts of ammonium (NH4+) and PO43− ions released during digestion. The results indicated that the performance of the anaerobic digestion in chemical oxygen demand removal changed between −4.0% and 15.4% for a Mg2+ concentration range of 277.2 to 529.3 mg/L and a PO43− concentration range of 377.4 to 2372.4 mg/L. There was an increase in the concentration of NH4+ in all reactors during digestion, but the extent of concentration increase could be controlled by increasing the initial concentrations of Mg2+ and PO43−. The maximum removal of NH4+ ions (33.7%) was observed in the reactor dosed initially by Mg2+ and PO43− concentrations of 467.2 and 2123.3 mg/L, respectively. The concentration of PO43− ion was lower than its initial concentration in all reactors, indicating considerable fixation of PO43− as it was released, by struvite and other solid species formation. The decrease in the concentration of Mg2+ ions similar to PO43− was accepted as evidence for the formation of solid species composed of Mg2+ and PO43, in addition to struvite.
- Open Access
- 1 December 2009
- Published by FapUNIFESP (SciELO) in Brazilian Journal of Pharmaceutical Sciences
- Vol. 45 (4) , 635-642
Estimating the turnover number in enzyme kinetic reactions using transient and stationary state data
Substrate and product concentration data obtained by simulating enzyme-substrate reaction rate equations were used to test two proposed kinetic rate constant estimation techniques in this study. In the first technique, the turnover number, k3, was calculated using early transient time domain data, which are difficult to obtain experimentally. The technique used an iterative approach to calculate k3 with a pair of data and the value of k3 could be retrieved with 35% error. The second technique calculated k3 using stationary domain data and the value of k3 could be retrieved with less than 5% error. This second technique also offered internal consistency in the calculation of k3 by calculating k3 both from the intercept and the slope of the linear plot derived in this study. A series of sensitivity analyses was conducted to understand the robustness of the second technique in estimating k3 from simulated data to the changes in the reaction rate constants (k1, k2, and k3) and the initial concentration of enzyme used for simulation. It was found that the second technique generally worked well in the estimation of k3 except for the simulated data for fast substrate conversions such as in the large k3 and [E]0 cases . This latter method, thus, shows promise for the use of late time experimental substrate/product concentration data to obtain k3. Exclusively using late time data avoids the need for difficult and expensive rapid early time measurement techniques for estimating k3. Once a reasonable estimate for k3 is obtained, the initial enzyme value can easily be determined from the maximum velocity constant established from fitting the Michaelis-Menten or Briggs-Haldane equations to substrate and product stationary state domain (late time) data. While the first technique can estimate k3 with only one point in the transient domain, it is suggested that the second method generally be favored since it only requires late-time stationary domain data and appears to be more accurate.
- 1 December 2009
- Published by FapUNIFESP (SciELO) in Brazilian Journal of Pharmaceutical Sciences
- Vol. 45 (4) , 635-642
Open AccessEstimating the turnover number in enzyme kinetic reactions using transient and stationary state data
Substrate and product concentration data obtained by simulating enzyme-substrate reaction rate equations were used to test two proposed kinetic rate constant estimation techniques in this study. In the first technique, the turnover number, k3, was calculated using early transient time domain data, which are difficult to obtain experimentally. The technique used an iterative approach to calculate k3 with a pair of data and the value of k3 could be retrieved with 35% error. The second technique calculated k3 using stationary domain data and the value of k3 could be retrieved with less than 5% error. This second technique also offered internal consistency in the calculation of k3 by calculating k3 both from the intercept and the slope of the linear plot derived in this study. A series of sensitivity analyses was conducted to understand the robustness of the second technique in estimating k3 from simulated data to the changes in the reaction rate constants (k1, k2, and k3) and the initial concentration of enzyme used for simulation. It was found that the second technique generally worked well in the estimation of k3 except for the simulated data for fast substrate conversions such as in the large k3 and [E]0 cases . This latter method, thus, shows promise for the use of late time experimental substrate/product concentration data to obtain k3. Exclusively using late time data avoids the need for difficult and expensive rapid early time measurement techniques for estimating k3. Once a reasonable estimate for k3 is obtained, the initial enzyme value can easily be determined from the maximum velocity constant established from fitting the Michaelis-Menten or Briggs-Haldane equations to substrate and product stationary state domain (late time) data. While the first technique can estimate k3 with only one point in the transient domain, it is suggested that the second method generally be favored since it only requires late-time stationary domain data and appears to be more accurate.
- 1 November 2009
- Published by Elsevier in Chemosphere
- Vol. 77 (8) , 1137-1142
Recovery of acids from anaerobic acidification broth by liquid–liquid extraction
- 1 November 2009
- Published by Elsevier in Chemosphere
- Vol. 77 (8) , 1137-1142
Recovery of acids from anaerobic acidification broth by liquid–liquid extraction
- 1 July 2009
- Published by Elsevier in Bioresource Technology
- Vol. 100 (13) , 3236-3244
Removal of ammonium and phosphate from the supernatant of anaerobically digested waste activated sludge by chemical precipitation
- 1 July 2009
- Published by Elsevier in Bioresource Technology
- Vol. 100 (13) , 3236-3244
Removal of ammonium and phosphate from the supernatant of anaerobically digested waste activated sludge by chemical precipitation
- 1 January 2008
- Published by Elsevier in Journal of Environmental Management
- Vol. 86 (1) , 193-200
Anaerobic digestion of dairy manure with enhanced ammonia removal
- 1 January 2008
- Published by Elsevier in Journal of Environmental Management
- Vol. 86 (1) , 193-200
Anaerobic digestion of dairy manure with enhanced ammonia removal
- 1 January 2007
- Published by Inderscience Publishers in Progress in Industrial Ecology, An International Journal
- Vol. 4 (1/2) , 91
Identification of eco-efficiency opportunities in a small enterprise producing vegetable oil in Eskisehir, Turkey
In this study, the current processes and technologies in a small enterprise, Demircanlar Oil Industry (Eskisehir, Turkey), were audited and improved from the eco-efficiency point of view. The eco-efficient management of the vegetable oil production processes has been performed on the units of physical processes, extraction and purification. The results obtained indicated that the loss in raw material can be reduced simply by increasing the height of the sieves used to separate foreign materials (leaves, sand, stones, etc.) from sunflower seeds. Results also indicated that production costs and negative environmental impacts can be decreased by minimising the loss of hexane during the extraction process, and the product quality can be improved and product loss can be prevented by adjusting the amounts of bleaching clay and TriSyl? in the bleaching process. Although the reduction in environmental impacts of the factory could not be valuated, the study showed that the factory can be managed more eco-efficiently without undergoing major process changes with an immediate benefit of approximately 12,000 USD.
- 1 January 2007
- Published by Inderscience Publishers in Progress in Industrial Ecology, An International Journal
- Vol. 4 (1/2) , 91
Identification of eco-efficiency opportunities in a small enterprise producing vegetable oil in Eskisehir, Turkey
In this study, the current processes and technologies in a small enterprise, Demircanlar Oil Industry (Eskisehir, Turkey), were audited and improved from the eco-efficiency point of view. The eco-efficient management of the vegetable oil production processes has been performed on the units of physical processes, extraction and purification. The results obtained indicated that the loss in raw material can be reduced simply by increasing the height of the sieves used to separate foreign materials (leaves, sand, stones, etc.) from sunflower seeds. Results also indicated that production costs and negative environmental impacts can be decreased by minimising the loss of hexane during the extraction process, and the product quality can be improved and product loss can be prevented by adjusting the amounts of bleaching clay and TriSyl? in the bleaching process. Although the reduction in environmental impacts of the factory could not be valuated, the study showed that the factory can be managed more eco-efficiently without undergoing major process changes with an immediate benefit of approximately 12,000 USD.
- 1 December 2005
- Published by Elsevier in Process Biochemistry
- Vol. 40 (12) , 3667-3674
Ammonia removal from anaerobically digested dairy manure by struvite precipitation
- 1 December 2005
- Published by Elsevier in Process Biochemistry
- Vol. 40 (12) , 3667-3674
Ammonia removal from anaerobically digested dairy manure by struvite precipitation
- 1 February 2005
- Published by Taylor & Francis in Environmental Technology
- Vol. 26 (2) , 171-178
Control of Trichloroethylene Emissions from Sparging Systems by Horizontal Bio- and Chemo- Barriers
The scope of this study was to develop a continuous system to clean-up a trichloroethylene (TCE) contaminated gas stream, where biotic and abiotic removal mechanisms are undertaken sequentially simulating the horizontal bio- and chemo-barriers proposed for the in-situ remediation of the contaminated sites. The bio- and chemo-barriers were simulated by using glass columns packed with granular anaerobic mixed culture and Fe(0) filings, respectively. The effect of gas residence time, which is adjusted by the gas flowrate, on the TCE removal efficiency of the reactor system was investigated. TCE removal efficiency of over 90% was achieved at gas residence times above 1hr. Furthermore, the effluent of reactor system contained only ethane and ethylene, which are non-toxic by-products of TCE reduction reactions, along with trace amounts of TCE.
- 1 February 2005
- Published by Taylor & Francis in Environmental Technology
- Vol. 26 (2) , 171-178
Control of Trichloroethylene Emissions from Sparging Systems by Horizontal Bio- and Chemo- Barriers
The scope of this study was to develop a continuous system to clean-up a trichloroethylene (TCE) contaminated gas stream, where biotic and abiotic removal mechanisms are undertaken sequentially simulating the horizontal bio- and chemo-barriers proposed for the in-situ remediation of the contaminated sites. The bio- and chemo-barriers were simulated by using glass columns packed with granular anaerobic mixed culture and Fe(0) filings, respectively. The effect of gas residence time, which is adjusted by the gas flowrate, on the TCE removal efficiency of the reactor system was investigated. TCE removal efficiency of over 90% was achieved at gas residence times above 1hr. Furthermore, the effluent of reactor system contained only ethane and ethylene, which are non-toxic by-products of TCE reduction reactions, along with trace amounts of TCE.
- 18 December 2003
- Published by Wiley in Environmental Quality Management
- Vol. 13 (2) , 67-75
Integrated preventive environmental management training for municipalities: A case study from Turkey
- 18 December 2003
- Published by Wiley in Environmental Quality Management
- Vol. 13 (2) , 67-75
Integrated preventive environmental management training for municipalities: A case study from Turkey