Hanzhou Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hanzhou Liu has a total of 92 co-authors. Here are the top co-authors by number of shared publications:
Shuya Zhang
Soochow University
6 shared publications- Jingye Li
Shanghai Normal University
5 shared publications Ming Yu
CAS Key Lab of Nuclear Radiation and Nuclear Energy Technology &CAS Key Lab of Interfacial Physics and Technology, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai, 201800, P. R. China
5 shared publicationsQing Li
4 shared publicationsWanxin Wen
4 shared publicationsWeiwei He
4 shared publications
Latest Publications
- Open Access
- 17 October 2025
- Published by Springer Nature in Research Square
Irradiation-Induced Facile Synthesis and Characterization of Red Blood Cell-Like Polystyrene Particles
This study developed a green γ-ray irradiation-assisted polymerization-self-assembly synergy strategy to fabricate red blood cell (RBC)-like morphology in an additive/template-free aqueous system at room temperature. By tuning the styrene/water mass ratio (2%–10%) and irradiation dose (5–100 kGy), we systematically elucidated the regulation mechanisms of microsphere morphology and size. Under optimized conditions (5 wt% styrene, 20 kGy), the microspheres exhibited typical RBC-like structures with an average diameter of 525 nm, hydroxyl-enriched surfaces, and internal hollow cavities. This approach eliminates the reliance on additives and templates in conventional processes.
- 17 October 2025
- Published by Springer Nature in Research Square
Open AccessIrradiation-Induced Facile Synthesis and Characterization of Red Blood Cell-Like Polystyrene Particles
This study developed a green γ-ray irradiation-assisted polymerization-self-assembly synergy strategy to fabricate red blood cell (RBC)-like morphology in an additive/template-free aqueous system at room temperature. By tuning the styrene/water mass ratio (2%–10%) and irradiation dose (5–100 kGy), we systematically elucidated the regulation mechanisms of microsphere morphology and size. Under optimized conditions (5 wt% styrene, 20 kGy), the microspheres exhibited typical RBC-like structures with an average diameter of 525 nm, hydroxyl-enriched surfaces, and internal hollow cavities. This approach eliminates the reliance on additives and templates in conventional processes.
- 11 May 2025
- Published by Elsevier in Radiation Physics and Chemistry
- Vol. 236
Metal-organic frameworks with high photoluminescence quantum yield for X-ray scintillators
- 11 May 2025
- Published by Elsevier in Radiation Physics and Chemistry
- Vol. 236
Metal-organic frameworks with high photoluminescence quantum yield for X-ray scintillators
- 25 March 2025
- Published by Springer Nature in Nature Sustainability
- Vol. 8 (5) , 553-561
Catalytic proton exchange in water distillation for efficient tritiated water clean-up
- 25 March 2025
- Published by Springer Nature in Nature Sustainability
- Vol. 8 (5) , 553-561
Catalytic proton exchange in water distillation for efficient tritiated water clean-up
- 13 August 2022
- Published by Springer Nature in Journal of Radioanalytical and Nuclear Chemistry
- Vol. 331 (9) , 3979-3986
Research on the separation and purification of 14C emissions from nuclear power plant by chemical exchange method
- 13 August 2022
- Published by Springer Nature in Journal of Radioanalytical and Nuclear Chemistry
- Vol. 331 (9) , 3979-3986
Research on the separation and purification of 14C emissions from nuclear power plant by chemical exchange method
- 15 July 2022
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 51 (31) , 11625-11629
Efficient neutron radiation shielding by boron–lithium imidazolate frameworks
Radiation protective materials are widely applied to avoid occupational hazards from either particle emissions or high-energy electromagnetic waves. Herein, we present a boron imidazolate framework (BIF) as a novel neutron shielding additive with high neutron capture cross-section elements B/Li and H. The BIF1-based epoxy resin matrix (Ep-BIF1) possesses high thermal stability and excellent resistance capacity. The neutron radiation shielding property was characterized using an Am–Be source, in which the thermal neutron shielding efficiency of Ep-BIF1 is notably higher than that of Ep-B4C with equal boron concentration, showing potential applications as an advanced efficient neutron radiation shielding composite.
- 15 July 2022
- Published by Royal Society of Chemistry (RSC) in Dalton Transactions
- Vol. 51 (31) , 11625-11629
Efficient neutron radiation shielding by boron–lithium imidazolate frameworks
Radiation protective materials are widely applied to avoid occupational hazards from either particle emissions or high-energy electromagnetic waves. Herein, we present a boron imidazolate framework (BIF) as a novel neutron shielding additive with high neutron capture cross-section elements B/Li and H. The BIF1-based epoxy resin matrix (Ep-BIF1) possesses high thermal stability and excellent resistance capacity. The neutron radiation shielding property was characterized using an Am–Be source, in which the thermal neutron shielding efficiency of Ep-BIF1 is notably higher than that of Ep-B4C with equal boron concentration, showing potential applications as an advanced efficient neutron radiation shielding composite.
- Open Access
- 1 January 2022
- Published by Walter de Gruyter GmbH in e-Polymers
- Vol. 22 (1) , 585-594
Effect of phenyltrimethoxysilane coupling agent (A153) on simultaneously improving mechanical, electrical, and processing properties of ultra-high-filled polypropylene composites
The improvement of mechanical properties, electrical properties, and processing properties of ultra-high-filled thermal insulation polypropylene (PP) composites has been plagued by high filling amount of heat-conducting fillers such as alumina powder (Al 2 O 3 ) and expanded graphite. In order to improve its properties, this article uses a high-temperature-resistant coupling agent (A153) to modify the PP composite. The results of this study show that when the content of A153 reaches 7.5 phr, the tensile strength of PP composite can reach 5 MPa, the elongation at break can reach 25%, and the volume resistivity can reach 12.8 × 10 12 Ω·m, and the maximum thermal conductivity is 1.82 W·m −1 ·K −1 . The processability also shows that the introduction of A153 can increase the melt flow rate and effectively improve the processability of the material.
- 1 January 2022
- Published by Walter de Gruyter GmbH in e-Polymers
- Vol. 22 (1) , 585-594
Open AccessEffect of phenyltrimethoxysilane coupling agent (A153) on simultaneously improving mechanical, electrical, and processing properties of ultra-high-filled polypropylene composites
The improvement of mechanical properties, electrical properties, and processing properties of ultra-high-filled thermal insulation polypropylene (PP) composites has been plagued by high filling amount of heat-conducting fillers such as alumina powder (Al 2 O 3 ) and expanded graphite. In order to improve its properties, this article uses a high-temperature-resistant coupling agent (A153) to modify the PP composite. The results of this study show that when the content of A153 reaches 7.5 phr, the tensile strength of PP composite can reach 5 MPa, the elongation at break can reach 25%, and the volume resistivity can reach 12.8 × 10 12 Ω·m, and the maximum thermal conductivity is 1.82 W·m −1 ·K −1 . The processability also shows that the introduction of A153 can increase the melt flow rate and effectively improve the processability of the material.
- 1 December 2021
- Published by Elsevier in Radiation Physics and Chemistry
- Vol. 189
One-step irradiation assisted fabrication of RGO/PAM hydrogel for air detritiation
- 1 December 2021
- Published by Elsevier in Radiation Physics and Chemistry
- Vol. 189
One-step irradiation assisted fabrication of RGO/PAM hydrogel for air detritiation
- 28 April 2020
- Published by Wiley in ChemistrySelect
- Vol. 5 (16) , 4961-4966
Synergistic Effects of Amine‐Containing Antioxidants on the Aging Performances of Ethylene Propylene Diene Rubber
In this study, two types of amine‐containing antioxidants composed of 2‐mercaptobenzimidazole zinc (MBZ) and 4,4′‐bis(α, α‐dimethylbenzyl) diphenylamine (445) were used to improve the thermo‐oxidative aging resistance of ethylene propylene diene rubber (EPDM). The synergistic effects on the performances of EPDM and the corresponding aging mechanism were investigated by FTIR, tensile test, differential scanning calorimetry (DSC), rotary rheometer and other equipment. The results showed that the hardness increased gradually with the increasing aging time regardless of the type of antioxidants. Compared with the EPDM without antioxidants, the elongation retention of those samples with MBZ or 445 improved obviously. Additionally, the sample with the MBZ/445 complex showed the highest retention values at the same aging time. The antioxidative mechanisms were further analyzed by carbonyl index, activation energy and oxidation induction time, respectively. Results indicated that the degree of oxidation of EPDM using the MBZ/445 complex was much lower than other control systems during the aging process. As a result, the MBZ/445 complex was a favorable antioxidative additive for EPDM.
- 28 April 2020
- Published by Wiley in ChemistrySelect
- Vol. 5 (16) , 4961-4966
Synergistic Effects of Amine‐Containing Antioxidants on the Aging Performances of Ethylene Propylene Diene Rubber
In this study, two types of amine‐containing antioxidants composed of 2‐mercaptobenzimidazole zinc (MBZ) and 4,4′‐bis(α, α‐dimethylbenzyl) diphenylamine (445) were used to improve the thermo‐oxidative aging resistance of ethylene propylene diene rubber (EPDM). The synergistic effects on the performances of EPDM and the corresponding aging mechanism were investigated by FTIR, tensile test, differential scanning calorimetry (DSC), rotary rheometer and other equipment. The results showed that the hardness increased gradually with the increasing aging time regardless of the type of antioxidants. Compared with the EPDM without antioxidants, the elongation retention of those samples with MBZ or 445 improved obviously. Additionally, the sample with the MBZ/445 complex showed the highest retention values at the same aging time. The antioxidative mechanisms were further analyzed by carbonyl index, activation energy and oxidation induction time, respectively. Results indicated that the degree of oxidation of EPDM using the MBZ/445 complex was much lower than other control systems during the aging process. As a result, the MBZ/445 complex was a favorable antioxidative additive for EPDM.
- Open Access
Using γ-Ray Polymerization-Induced Assemblies to Synthesize Polydopamine Nanocapsules
This work reports a simple and robust strategy for synthesis of polydopamine nanocapsules (PDA NCs). First, polymer assemblies were synthesized by a γ-ray-induced liquid–liquid (H2O–acrylate) interface polymerization strategy, in the absence of any surfactants. 1H nuclear magnetic resonance analysis and molecular dynamics simulation reveal that the generation of polymer assemblies largely depends on the hydrophilicity of acrylate and gravity of the oligomers at the interface. By virtue of the spherical structure and mechanic stability of the polymer assemblies, PDA NCs are next prepared by the interfacial polymerization of dopamine onto the assemblies, followed by the removal of templates by using ethanol. The polydopamine nanocapsules are shown to load and release ciprofloxacin (CIP, a model drug), such that the CIP-loaded PDA NCs are able to inhibit the growth of Escherichia coli.
Open AccessUsing γ-Ray Polymerization-Induced Assemblies to Synthesize Polydopamine Nanocapsules
This work reports a simple and robust strategy for synthesis of polydopamine nanocapsules (PDA NCs). First, polymer assemblies were synthesized by a γ-ray-induced liquid–liquid (H2O–acrylate) interface polymerization strategy, in the absence of any surfactants. 1H nuclear magnetic resonance analysis and molecular dynamics simulation reveal that the generation of polymer assemblies largely depends on the hydrophilicity of acrylate and gravity of the oligomers at the interface. By virtue of the spherical structure and mechanic stability of the polymer assemblies, PDA NCs are next prepared by the interfacial polymerization of dopamine onto the assemblies, followed by the removal of templates by using ethanol. The polydopamine nanocapsules are shown to load and release ciprofloxacin (CIP, a model drug), such that the CIP-loaded PDA NCs are able to inhibit the growth of Escherichia coli.