Mona M. Dardir
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mona M. Dardir has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Mohammed Abd El-Fattah
Production Department, Egyptian Petroleum Research Institute (EPRI), Cairo, Egypt
4 shared publications - Mahmoud Ibrahim Abdou
Egyptian Petroleum Research Institute
2 shared publications - Soad A. Mahmoud
Université Libanaise
2 shared publications A.A. Hafiz
1 shared publicationA.B. Farag
1 shared publicationA.M. Ramdan
1 shared publication
Latest Publications
- Open Access
- 1 December 2018
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 27 (4) , 1035-1041
Propylene glycol mono and di stearates as water in oil emulsifiers for oil-well drilling fluids
The objective of drilling operation is to drill, evaluate and complete a well that will produce oil and/or gas efficiently. The responsibility for performing these functions is held by using drilling mud. The research will focus on the oil base mud system due to the importance of that kind of drilling fluid which helped to address several drilling problems such as formation clays that react, swell or slough after expose to WBFs, increasing down hole temperatures, contaminants, stuck pipe, torque and drag. The research will rely on an economical-low cost prepared emulsifiers that used as W/O emulsifiers for oil base mud instead of the imported emulsifier. The new prepared emulsifiers provide an excellent options with emulsification power for oil-based mud that formulated from diesel oil and water. The nonionic emulsifiers were prepared through the esterification reaction of propylene glycol (1 mol) and stearic acid (1 mol) and/or (2 mol), the products were two oil soluble nonionic emulsifiers with hydrophilic/lipophilic balance (HLB) of 3.4 and 2.8 respectively. The chemical structure was confirmed using elemental analysis, FTIR and 1H NMR. The new prepared emulsifiers were evaluated as primary emulsifiers for oil – base mud and the results were compared with the currently used primary emulsifier. The obtained results exhibited interesting rheology properties and shear-thinning behavior, yield value, thixotropy, gel strength and filter loss.
- 1 December 2018
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 27 (4) , 1035-1041
Open AccessPropylene glycol mono and di stearates as water in oil emulsifiers for oil-well drilling fluids
The objective of drilling operation is to drill, evaluate and complete a well that will produce oil and/or gas efficiently. The responsibility for performing these functions is held by using drilling mud. The research will focus on the oil base mud system due to the importance of that kind of drilling fluid which helped to address several drilling problems such as formation clays that react, swell or slough after expose to WBFs, increasing down hole temperatures, contaminants, stuck pipe, torque and drag. The research will rely on an economical-low cost prepared emulsifiers that used as W/O emulsifiers for oil base mud instead of the imported emulsifier. The new prepared emulsifiers provide an excellent options with emulsification power for oil-based mud that formulated from diesel oil and water. The nonionic emulsifiers were prepared through the esterification reaction of propylene glycol (1 mol) and stearic acid (1 mol) and/or (2 mol), the products were two oil soluble nonionic emulsifiers with hydrophilic/lipophilic balance (HLB) of 3.4 and 2.8 respectively. The chemical structure was confirmed using elemental analysis, FTIR and 1H NMR. The new prepared emulsifiers were evaluated as primary emulsifiers for oil – base mud and the results were compared with the currently used primary emulsifier. The obtained results exhibited interesting rheology properties and shear-thinning behavior, yield value, thixotropy, gel strength and filter loss.
- Open Access
- 1 March 2017
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 26 (1) , 67-77
Preparation and evaluation of cationic bolaform surfactants for water-based drilling fluids
Three cationic bolaform surfactants with different spacer lengths were prepared from the reaction of two moles of triisopropanolamine with one mole of each of the following 1,4-dibromobutane, 1,5-dibromopentane and 1,6-dibromohexane. The chemical structures of the prepared compounds were confirmed via: FTIR spectroscopy, 1H NMR and elemental microanalysis. The surface activity of these bolaform surfactants was studied. The prepared cationic bolaform surfactants were evaluated as viscosifier additives for water-based drilling fluids. The evaluation includes the study of rheological properties of the formulated mud (apparent viscosity, plastic viscosity and yield point, gel strength and thixotropy), effect of temperature on the rheological properties and also, the study of mineralogical properties of the water-based before and after treatment with the prepared surfactants using: X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). The results of the evaluation were compared to the water-based mud formulated from commercial grade bentonite
- 1 March 2017
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 26 (1) , 67-77
Open AccessPreparation and evaluation of cationic bolaform surfactants for water-based drilling fluids
Three cationic bolaform surfactants with different spacer lengths were prepared from the reaction of two moles of triisopropanolamine with one mole of each of the following 1,4-dibromobutane, 1,5-dibromopentane and 1,6-dibromohexane. The chemical structures of the prepared compounds were confirmed via: FTIR spectroscopy, 1H NMR and elemental microanalysis. The surface activity of these bolaform surfactants was studied. The prepared cationic bolaform surfactants were evaluated as viscosifier additives for water-based drilling fluids. The evaluation includes the study of rheological properties of the formulated mud (apparent viscosity, plastic viscosity and yield point, gel strength and thixotropy), effect of temperature on the rheological properties and also, the study of mineralogical properties of the water-based before and after treatment with the prepared surfactants using: X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). The results of the evaluation were compared to the water-based mud formulated from commercial grade bentonite
- 4 October 2016
- Published by Wiley in Journal of Surfactants and Detergents
- Vol. 19 (6) , 1263-1272
Synthesis and Evaluation of Bis‐quaternary‐Based Surfactants as Additives for Water‐Based Mud
Two series of cationic gemini surfactants, alkanediyl‐α,ω‐bis[N,N‐dimethyl alkyl (octyl or dodecyl)ammonium] dibromide (R‐s‐R; s = 6, 10, 12 and R = 8 and 12) were prepared and evaluated as additives for water‐based mud. The chemical structures of the prepared surfactants were confirmed using FTIR and mass spectroscopy. Surface activity of these compounds has been studied and their surface properties including surface tension, emulsification power, critical micelle concentration, effectiveness, maximum surface excess and minimum surface area were determined. The results showed that the prepared compounds have significant surface activity, especially those of longer hydrophobic chain length. The prepared cationic gemini surfactants were evaluated as viscosifiers and filter loss additives for water‐based mud formulated from local Na‐montmorillonite clay. XRD analysis was carried out to the Na‐montmorillonite clay to determine the interaction of the surfactants with inter layers of the clay structure. Rheological properties, gel strength, thixotropy, filtration properties and the effect of temperature on rheological properties of the water‐based mud were studied. The results indicated that the gemini surfactants have a positive effect on the rheological and filtration properties of the Na‐montmorillonite clay according to American Petroleum Institute specifications.
- 4 October 2016
- Published by Wiley in Journal of Surfactants and Detergents
- Vol. 19 (6) , 1263-1272
Synthesis and Evaluation of Bis‐quaternary‐Based Surfactants as Additives for Water‐Based Mud
Two series of cationic gemini surfactants, alkanediyl‐α,ω‐bis[N,N‐dimethyl alkyl (octyl or dodecyl)ammonium] dibromide (R‐s‐R; s = 6, 10, 12 and R = 8 and 12) were prepared and evaluated as additives for water‐based mud. The chemical structures of the prepared surfactants were confirmed using FTIR and mass spectroscopy. Surface activity of these compounds has been studied and their surface properties including surface tension, emulsification power, critical micelle concentration, effectiveness, maximum surface excess and minimum surface area were determined. The results showed that the prepared compounds have significant surface activity, especially those of longer hydrophobic chain length. The prepared cationic gemini surfactants were evaluated as viscosifiers and filter loss additives for water‐based mud formulated from local Na‐montmorillonite clay. XRD analysis was carried out to the Na‐montmorillonite clay to determine the interaction of the surfactants with inter layers of the clay structure. Rheological properties, gel strength, thixotropy, filtration properties and the effect of temperature on rheological properties of the water‐based mud were studied. The results indicated that the gemini surfactants have a positive effect on the rheological and filtration properties of the Na‐montmorillonite clay according to American Petroleum Institute specifications.
- 1 August 2016
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 89, 190-197
Synthesis of cuprous oxide epoxy nanocomposite as an environmentally antimicrobial coating
- 1 August 2016
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 89, 190-197
Synthesis of cuprous oxide epoxy nanocomposite as an environmentally antimicrobial coating
- Open Access
- 1 June 2016
- Published by Elsevier in Egyptian Journal of Petroleum
- Vol. 25 (2) , 281-291
High performance nature of biodegradable polymeric nanocomposites for oil-well drilling fluids
- 1 June 2016
- Published by Elsevier in Egyptian Journal of Petroleum
- Vol. 25 (2) , 281-291
Open AccessHigh performance nature of biodegradable polymeric nanocomposites for oil-well drilling fluids
- 1 January 2015
- Published by Elsevier in Progress in Organic Coatings
- Vol. 78, 83-89
Synthesis and characterization of titanium oxide nanotubes and its performance in epoxy nanocomposite coating
- 1 January 2015
- Published by Elsevier in Progress in Organic Coatings
- Vol. 78, 83-89
Synthesis and characterization of titanium oxide nanotubes and its performance in epoxy nanocomposite coating
- Open Access
- 1 March 2014
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 23 (1) , 35-43
Preparation and evaluation of some esteramides as synthetic based drilling fluids
Some hexanamide-mono and di-linoleniate esters were prepared by the reaction of linolenic acid and hexanamide (derived from the reaction of hexanoic acid and diethanolamine). The chemical structure for the newly prepared hexanamide-mono and di-linoleniate esters were elucidated using elemental analysis, (FTIR), H 1NMR and chemical ionization mass spectra (CI/Ms) spectroscopic techniques. The results of the spectroscopic analysis indicated that they were prepared through the right method and they have high purity. The new prepared esters have high biodegradability and lower toxicity (environmentally friendly) so they were evaluated as a synthetic-based mud (ester-based mud) for oil-well drilling fluids. The evaluation included study of the rheological properties, filtration and thermal properties of the ester based-muds formulated with the newly prepared esters compared to the reference commercial synthetic-based mud
- 1 March 2014
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 23 (1) , 35-43
Open AccessPreparation and evaluation of some esteramides as synthetic based drilling fluids
Some hexanamide-mono and di-linoleniate esters were prepared by the reaction of linolenic acid and hexanamide (derived from the reaction of hexanoic acid and diethanolamine). The chemical structure for the newly prepared hexanamide-mono and di-linoleniate esters were elucidated using elemental analysis, (FTIR), H 1NMR and chemical ionization mass spectra (CI/Ms) spectroscopic techniques. The results of the spectroscopic analysis indicated that they were prepared through the right method and they have high purity. The new prepared esters have high biodegradability and lower toxicity (environmentally friendly) so they were evaluated as a synthetic-based mud (ester-based mud) for oil-well drilling fluids. The evaluation included study of the rheological properties, filtration and thermal properties of the ester based-muds formulated with the newly prepared esters compared to the reference commercial synthetic-based mud
- 11 October 2013
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 31 (22) , 2335-2347
Ether-Based Muds Show Promise for Replacing Some Oil-Based Muds
Two different polyethers were evaluated for their potential use in drilling fluids as a base fluid for synthetic ether-based mud, which is one type of synthetic-based drilling fluid that are used when drilling for oil and gas by a rotary method and they have several technological and environmental advantages over oil-based mud. Polyglycerol or polytriethanolamine, which derive from the condensation reaction of glycerol or triethanolamine was used as a base fluid in the formulation of ether-based mud in comparison with oil based mud. The evaluation includes the study of rheology, filtration properties, electrical stability, and thermal stability for oil-based mud and synthetic ether-based mud, which are formulated of polyglycerol or polytriethanolamine. The result show that the tested synthetic ether-based mud are more viscous at low temperature, thin more with increasing temperature, and have high thermal stability than oil-based mud. Biodegradation of the mud formulated with polyglycerol or polytriethanolamine was also studied.
- 11 October 2013
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 31 (22) , 2335-2347
Ether-Based Muds Show Promise for Replacing Some Oil-Based Muds
Two different polyethers were evaluated for their potential use in drilling fluids as a base fluid for synthetic ether-based mud, which is one type of synthetic-based drilling fluid that are used when drilling for oil and gas by a rotary method and they have several technological and environmental advantages over oil-based mud. Polyglycerol or polytriethanolamine, which derive from the condensation reaction of glycerol or triethanolamine was used as a base fluid in the formulation of ether-based mud in comparison with oil based mud. The evaluation includes the study of rheology, filtration properties, electrical stability, and thermal stability for oil-based mud and synthetic ether-based mud, which are formulated of polyglycerol or polytriethanolamine. The result show that the tested synthetic ether-based mud are more viscous at low temperature, thin more with increasing temperature, and have high thermal stability than oil-based mud. Biodegradation of the mud formulated with polyglycerol or polytriethanolamine was also studied.
- Open Access
- 1 June 2013
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 22 (1) , 53-59
Evaluation of Egyptian bentonite and nano-bentonite as drilling mud
Nano-particles of bentonite have been prepared by nano-grinding. The nano-bentonite was characterized by X-ray fluorescence analysis (XRF), X-ray powder diffraction (XRD), thermal gravimetric analysis (TGA) and Transmission electron microscopy (TEM). The bentonite particles had been ground to the size ranging from 4 to 9nm. Both natural and nano-bentonite were evaluated as drilling mud. The evaluation involved the study of the rheological properties, filtration and gel strength before and after treatment with viscosities and filter loss agent, and compared with the American Petroleum Institute API bentonite. With decreasing the grain size of bentonite to the nano-scale, the results were not satisfied to the API -standard
- 1 June 2013
- Published by Egyptian Petroleum Research Institute in Egyptian Journal of Petroleum
- Vol. 22 (1) , 53-59
Open AccessEvaluation of Egyptian bentonite and nano-bentonite as drilling mud
Nano-particles of bentonite have been prepared by nano-grinding. The nano-bentonite was characterized by X-ray fluorescence analysis (XRF), X-ray powder diffraction (XRD), thermal gravimetric analysis (TGA) and Transmission electron microscopy (TEM). The bentonite particles had been ground to the size ranging from 4 to 9nm. Both natural and nano-bentonite were evaluated as drilling mud. The evaluation involved the study of the rheological properties, filtration and gel strength before and after treatment with viscosities and filter loss agent, and compared with the American Petroleum Institute API bentonite. With decreasing the grain size of bentonite to the nano-scale, the results were not satisfied to the API -standard