Alojz Kopáčik
Alojz Kopáčik has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Ján Erdélyi
Department of Surveying, Faculty of Civil Engineering, Slovak University of Technology, 810 05 Bratislava, Slovakia
13 shared publications - Pavol Kajánek
Department of Surveying, Faculty of Civil Engineering, Slovak University of Technology in Bratislava, 81005 Bratislava, Slovakia
7 shared publications - Richard Honti
Department of Surveying, Faculty of Civil Engineering, Slovak University of Technology in Bratislava, Radlinskeho 11, 810 05 Bratislava, Slovakia
6 shared publications Peter Kyrinovič
Slovak University of Technology in Bratislava
5 shared publications- Peter Kyrinovič
Department of Surveying, Faculty of Civil Engineering, Slovak University of Technology in Bratislava, Radlinskeho 11, 810 05 Bratislava, Slovakia
5 shared publications - Imrich Lipták
Slovak University of Technology, Faculty of Civil Engineering, Radlinskeho 11, 81368 Bratislava, Slovakia
3 shared publications
Latest Publications
- Open Access
Metrology of Short-Length Measurers—Development of a Comparator for the Calibration of Measurers Based on Image Processing and Interferometric Measurements
For the calibration of linear scales, comparators are generally used. Comparators are devices that enable the movement of an evaluation apparatus over a calibrated scale along a linear base with high precision. The construction of a comparator includes a movable carriage that carries the device for the evaluation of the position of the given edge of the line scale relative to the beginning of the scale. In principle, it involves a camera capturing the scale of the measurer, where the position of the camera’s projection center is measured using an interferometer. This article addresses the development of a comparator assembled from low-cost components, as well as the description of systematic influences related to the movement of individual parts of the system, such as the inclination and rotation of the camera and directional and height deviations during the carriage’s movement. This article also includes an evaluation of the edge of the given scale with subpixel accuracy, addressing distortion elimination and excluding the influences of impurities or imperfections on the scale. The proposed solution was applied to linear-scale measurers, such as leveling rods with coded and conventional scales and measuring tapes. The entire process of measurement and evaluation was automated.
Open AccessMetrology of Short-Length Measurers—Development of a Comparator for the Calibration of Measurers Based on Image Processing and Interferometric Measurements
For the calibration of linear scales, comparators are generally used. Comparators are devices that enable the movement of an evaluation apparatus over a calibrated scale along a linear base with high precision. The construction of a comparator includes a movable carriage that carries the device for the evaluation of the position of the given edge of the line scale relative to the beginning of the scale. In principle, it involves a camera capturing the scale of the measurer, where the position of the camera’s projection center is measured using an interferometer. This article addresses the development of a comparator assembled from low-cost components, as well as the description of systematic influences related to the movement of individual parts of the system, such as the inclination and rotation of the camera and directional and height deviations during the carriage’s movement. This article also includes an evaluation of the edge of the given scale with subpixel accuracy, addressing distortion elimination and excluding the influences of impurities or imperfections on the scale. The proposed solution was applied to linear-scale measurers, such as leveling rods with coded and conventional scales and measuring tapes. The entire process of measurement and evaluation was automated.
- 1 January 2024
- Published by Slovak University of Technology in Bratislava
Automatizácia segmentácie základných geometrických primitív z mračien bodov
This book primarily explores the segmentation of fundamental geometric shapes from point clouds. It delves into the development of algorithms for filtering point clouds, utilizing local density and the variation of normal vectors within a specified neighborhood. These filtering algorithms are integrated into the segmentation processes but can also function independently. Additionally, the book proposes algorithms for segmenting planes, cylinders, and spheres, which are the most common geometric features in civil engineering.
- 1 January 2024
- Published by Slovak University of Technology in Bratislava
Automatizácia segmentácie základných geometrických primitív z mračien bodov
This book primarily explores the segmentation of fundamental geometric shapes from point clouds. It delves into the development of algorithms for filtering point clouds, utilizing local density and the variation of normal vectors within a specified neighborhood. These filtering algorithms are integrated into the segmentation processes but can also function independently. Additionally, the book proposes algorithms for segmenting planes, cylinders, and spheres, which are the most common geometric features in civil engineering.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2887 (1)
3D mapping system based on a fusion of 2D lidars
The article presents a proposed mapping system that uses three stably located 2D lidars to map the indoor environment and create a model. Each lidar has its sensor frame, whose position and orientation change during the measurement. For this purpose, simultaneous mapping and localisation SLAM is used. By transforming lidar scans into a global coordinate system, the system’s change of position and orientation is calculated. The accuracy of the transformation is affected by the surrounding environment, where narrow straight corridors make it challenging to calculate the transformation. Errors in the determination of transformation parameters (translation and rotation) accumulate in the calculated position and orientation of the system. These errors are then transferred to the created model of the environment. The accuracy of determining the position and orientation of the system is increased by using additional sensors such as an inertial measuring unit, speed sensor, and stereo camera. Part of the data processing is identifying the repeatedly traversed area by optimising the trajectory and model. The proposed system is low-cost, portable, and allows 2D lidar when navigating and mapping the surrounding 3D space. The system’s accuracy is evaluated based on comparison results with the reference model.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2887 (1)
Open Access3D mapping system based on a fusion of 2D lidars
The article presents a proposed mapping system that uses three stably located 2D lidars to map the indoor environment and create a model. Each lidar has its sensor frame, whose position and orientation change during the measurement. For this purpose, simultaneous mapping and localisation SLAM is used. By transforming lidar scans into a global coordinate system, the system’s change of position and orientation is calculated. The accuracy of the transformation is affected by the surrounding environment, where narrow straight corridors make it challenging to calculate the transformation. Errors in the determination of transformation parameters (translation and rotation) accumulate in the calculated position and orientation of the system. These errors are then transferred to the created model of the environment. The accuracy of determining the position and orientation of the system is increased by using additional sensors such as an inertial measuring unit, speed sensor, and stereo camera. Part of the data processing is identifying the repeatedly traversed area by optimising the trajectory and model. The proposed system is low-cost, portable, and allows 2D lidar when navigating and mapping the surrounding 3D space. The system’s accuracy is evaluated based on comparison results with the reference model.
- Open Access
- 14 September 2022
- Published by MDPI AG in Remote Sensing
- Vol. 14 (18) , 4591
Semi-Automated Segmentation of Geometric Shapes from Point Clouds
Building information models (BIM) in the civil industry are very popular nowadays. The basic information of these models is the 3D geometric model of a building structure. The most applied methodology to model the existing buildings is by generating 3D geometric information from point clouds provided by laser scanners. The fundamental principle of this methodology is the recognition of structures shaped in basic geometric primitives, e.g., planes, spheres, and cylinders. The basic premise of the efficiency of this methodology is the automation of detection, since manual segmentation of a point cloud can be challenging, time-consuming, and, therefore, inefficient. This paper presents a novel algorithm for the automated segmentation of geometric shapes in point clouds without needing pre-segmentation. With the designed algorithm, structures formed in three types of basic geometrical primitive can be identified and segmented: planar (e.g., walls, floors, ceilings), spherical (e.g., laser scanner reference targets), and cylindrical (e.g., columns, pillars, piping). The RANSAC paradigm partially inspires the proposed algorithm; however, various modifications must be made. The algorithm was tested on several point clouds and was compared with the standard RANSAC algorithm; this part is described in the last section of the paper. One of the tests was performed on a double cylinder-shaped test object, the parameters (radius and height) of this object were available with high accuracy (0.1 mm), and the differences between the known and estimated parameters were below 0.5 mm in each case, indicating the correctness of the proposed algorithm. Also, a comparison with the standard RANSAC algorithm was performed, where the algorithm proposed showed better results than the standard RANSAC algorithm. The segmentation quality was, on average, increased from 50% to 100%.
- 14 September 2022
- Published by MDPI AG in Remote Sensing
- Vol. 14 (18) , 4591
Open AccessSemi-Automated Segmentation of Geometric Shapes from Point Clouds
Building information models (BIM) in the civil industry are very popular nowadays. The basic information of these models is the 3D geometric model of a building structure. The most applied methodology to model the existing buildings is by generating 3D geometric information from point clouds provided by laser scanners. The fundamental principle of this methodology is the recognition of structures shaped in basic geometric primitives, e.g., planes, spheres, and cylinders. The basic premise of the efficiency of this methodology is the automation of detection, since manual segmentation of a point cloud can be challenging, time-consuming, and, therefore, inefficient. This paper presents a novel algorithm for the automated segmentation of geometric shapes in point clouds without needing pre-segmentation. With the designed algorithm, structures formed in three types of basic geometrical primitive can be identified and segmented: planar (e.g., walls, floors, ceilings), spherical (e.g., laser scanner reference targets), and cylindrical (e.g., columns, pillars, piping). The RANSAC paradigm partially inspires the proposed algorithm; however, various modifications must be made. The algorithm was tested on several point clouds and was compared with the standard RANSAC algorithm; this part is described in the last section of the paper. One of the tests was performed on a double cylinder-shaped test object, the parameters (radius and height) of this object were available with high accuracy (0.1 mm), and the differences between the known and estimated parameters were below 0.5 mm in each case, indicating the correctness of the proposed algorithm. Also, a comparison with the standard RANSAC algorithm was performed, where the algorithm proposed showed better results than the standard RANSAC algorithm. The segmentation quality was, on average, increased from 50% to 100%.
- Open Access
- 6 December 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (23) , 8731
Spatial Data Analysis for Deformation Monitoring of Bridge Structures
Weather conditions and different operational loads often cause changes in essential parts of engineering structures, and this affects the static and dynamic behavior and reliability of these structures. Therefore, geodetic monitoring is an integral part of the diagnosis of engineering structures and provides essential information about the current state (condition) of the structure. The development of measuring instruments enables deformation analyses of engineering structures using non-conventional surveying methods. Nowadays, one of the most effective techniques for spatial data collection is terrestrial laser scanning (TLS). TLS is frequently used for data acquisition in cases where three-dimensional (3D) data with high resolution is needed. Using suitable data processing, TLS can be used for static deformation analysis of the structure being monitored. For dynamic deformation measurements (structural health monitoring) of bridge structures, ground-based radar interferometry and accelerometers are often used for vibration mode determination using spectral analysis of frequencies. This paper describes experimental deformation monitoring of structures performed using TLS and ground-based radar interferometry. The procedure of measurement, the analysis of the acquired spatial data, and the results of deformation monitoring are explained and described.
- 6 December 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (23) , 8731
Open AccessSpatial Data Analysis for Deformation Monitoring of Bridge Structures
Weather conditions and different operational loads often cause changes in essential parts of engineering structures, and this affects the static and dynamic behavior and reliability of these structures. Therefore, geodetic monitoring is an integral part of the diagnosis of engineering structures and provides essential information about the current state (condition) of the structure. The development of measuring instruments enables deformation analyses of engineering structures using non-conventional surveying methods. Nowadays, one of the most effective techniques for spatial data collection is terrestrial laser scanning (TLS). TLS is frequently used for data acquisition in cases where three-dimensional (3D) data with high resolution is needed. Using suitable data processing, TLS can be used for static deformation analysis of the structure being monitored. For dynamic deformation measurements (structural health monitoring) of bridge structures, ground-based radar interferometry and accelerometers are often used for vibration mode determination using spectral analysis of frequencies. This paper describes experimental deformation monitoring of structures performed using TLS and ground-based radar interferometry. The procedure of measurement, the analysis of the acquired spatial data, and the results of deformation monitoring are explained and described.
- 7 November 2020
- Published by Akademiai Kiado Zrt. in Pollack Periodica
- Vol. 15 (3) , 60-71
Warm-Up Effect and Warm-Up Time of a Laser Tracker
The warm-up effect is a well-known phenomenon, which occurs in all types of laser trackers. The series of experiments was performed to determine the influence of warm-up effect on measurement and a warm-up time of device – the time after the temperature inside the tracker is stable. In this paper, the tested tracker was Leica AT960-MR. Results showed that the warm-up effect could cause errors up to tenths of millimeters, and a warm-up time of instrument is around two hours, which is similar to the other researches.
- 7 November 2020
- Published by Akademiai Kiado Zrt. in Pollack Periodica
- Vol. 15 (3) , 60-71
Warm-Up Effect and Warm-Up Time of a Laser Tracker
The warm-up effect is a well-known phenomenon, which occurs in all types of laser trackers. The series of experiments was performed to determine the influence of warm-up effect on measurement and a warm-up time of device – the time after the temperature inside the tracker is stable. In this paper, the tested tracker was Leica AT960-MR. Results showed that the warm-up effect could cause errors up to tenths of millimeters, and a warm-up time of instrument is around two hours, which is similar to the other researches.
- 7 November 2020
- Published by Akademiai Kiado Zrt. in Pollack Periodica
- Vol. 15 (3) , 15-25
Automated Sphere Segmentation from Point Clouds
Nowadays huge datasets can be collected in a relatively short time. After capturing these data sets the next step is their processing. Automation of the processing steps can contribute to efficiency increase, to reduction of the time needed for processing, and to reduction of interactions of the user. The paper brings a short review of the most reliable methods for sphere segmentation. An innovative algorithm for automated detection of spheres and for estimating their parameters from 3D point clouds is introduced. The algorithm proposed was tested on complex point clouds. In the last part of the paper, the implementation of the algorithm proposed to a standalone application is described.
- 7 November 2020
- Published by Akademiai Kiado Zrt. in Pollack Periodica
- Vol. 15 (3) , 15-25
Automated Sphere Segmentation from Point Clouds
Nowadays huge datasets can be collected in a relatively short time. After capturing these data sets the next step is their processing. Automation of the processing steps can contribute to efficiency increase, to reduction of the time needed for processing, and to reduction of interactions of the user. The paper brings a short review of the most reliable methods for sphere segmentation. An innovative algorithm for automated detection of spheres and for estimating their parameters from 3D point clouds is introduced. The algorithm proposed was tested on complex point clouds. In the last part of the paper, the implementation of the algorithm proposed to a standalone application is described.
- 20 October 2020
- Published by Springer Nature
- p. 142-154
Analysis of Warm-up Effect on Laser Tracker Measurement Performance
- 20 October 2020
- Published by Springer Nature
- p. 142-154
Analysis of Warm-up Effect on Laser Tracker Measurement Performance
- 20 October 2020
- Published by Springer Nature
- p. 27-37
Possibility of Use of BIM in Automated Geometry Check of Structures
- 20 October 2020
- Published by Springer Nature
- p. 27-37
Possibility of Use of BIM in Automated Geometry Check of Structures
- 20 October 2020
- Published by Springer Nature
- p. 13-26
Building Information Modelling of Industrial Plants
- 20 October 2020
- Published by Springer Nature
- p. 13-26
Building Information Modelling of Industrial Plants