Wenjun Ge
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wenjun Ge has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
Feng Lin
8 shared publicationsChao Guo
Department of Mechanical Engineering, Tsinghua University, Beijing, China
5 shared publicationsStephen Lin
3 shared publicationsWentao Yan
Department of Mechanical Engineering, National University of Singapore, Singapore, Singapore
3 shared publications- Wentao Yan
Department of Mechanical Engineering, National University of Singapore, Singapore, Singapore
3 shared publications Wing Kam Liu
3 shared publications
Latest Publications
- 18 October 2025
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 37 (9) , 1-18
Towards health monitoring of laser powder bed fusion using acoustic emissions: identify manufacturing parameters
- 18 October 2025
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 37 (9) , 1-18
Towards health monitoring of laser powder bed fusion using acoustic emissions: identify manufacturing parameters
- 16 June 2023
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 35 (5) , 2313-2326
Data-driven prediction of keyhole features in metal additive manufacturing based on physics-based simulation
- 16 June 2023
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 35 (5) , 2313-2326
Data-driven prediction of keyhole features in metal additive manufacturing based on physics-based simulation
- Open Access
Investigation of Laser Butt Welding of AISI 304L and Q235 Steels Based on Numerical and Experimental Analyses
The fiber laser butt welding of AISI 304L and Q235 low-carbon steel is performed in this study. An integrated heat source combined with an asymmetric double-ellipsoidal heat source and a cylindrical heat source is designed to perform the numerical simulation of the laser butt welding process. With the established numerical simulation model, the formation of the welded joint is studied by investigating the thermal process. The effects of the laser power and laser beam offset to the sides of the center of the welding gap on the welded joint shape and strength are experimentally investigated, and the optimum laser power and laser beam offset are determined via tensile strength and hardness tests of the weldment. The numerical simulation results based on the asymmetric heat source agree well with the experimental results and are applied to investigate the mechanisms for forming different welded joint shapes in AISI 304L and Q235 steels. The different thermal conductivity and melting temperatures of the two dissimilar metals result in the different shapes of the welded joint.
Open AccessInvestigation of Laser Butt Welding of AISI 304L and Q235 Steels Based on Numerical and Experimental Analyses
The fiber laser butt welding of AISI 304L and Q235 low-carbon steel is performed in this study. An integrated heat source combined with an asymmetric double-ellipsoidal heat source and a cylindrical heat source is designed to perform the numerical simulation of the laser butt welding process. With the established numerical simulation model, the formation of the welded joint is studied by investigating the thermal process. The effects of the laser power and laser beam offset to the sides of the center of the welding gap on the welded joint shape and strength are experimentally investigated, and the optimum laser power and laser beam offset are determined via tensile strength and hardness tests of the weldment. The numerical simulation results based on the asymmetric heat source agree well with the experimental results and are applied to investigate the mechanisms for forming different welded joint shapes in AISI 304L and Q235 steels. The different thermal conductivity and melting temperatures of the two dissimilar metals result in the different shapes of the welded joint.
- Open Access
- 29 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 17365-17376
A Low-Cost Welding Status Monitoring Framework for High-Power Disk Laser Welding (December 2018)
Welding status determines the post-weld quality and is crucial to high-power disk laser welding. A low-cost monitoring system based on photodiodes is developed to monitor the real-time welding statuses in this research. A deep learning architecture based on stacked autoencoder (SAE) is proposed to automatically learn more representative features of welding statuses from the raw signal features captured by the visible light photodiode and the reflected laser light photodiode without any manual operations. The maximum correntropy loss function is applied to improve the learning ability of the proposed SAE method. Furthermore, a genetic algorithm (GA) is applied to optimize the key parameters of the proposed SAE method. The proposed SAE is applied to the high-power disk laser welding experiments and shows better performance in welding status monitoring than the standard AE framework and the conventional SVM and BP method. Additional experiments with different welding parameters validate the effectiveness and robustness of our proposed SAE method.
- 29 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 17365-17376
Open AccessA Low-Cost Welding Status Monitoring Framework for High-Power Disk Laser Welding (December 2018)
Welding status determines the post-weld quality and is crucial to high-power disk laser welding. A low-cost monitoring system based on photodiodes is developed to monitor the real-time welding statuses in this research. A deep learning architecture based on stacked autoencoder (SAE) is proposed to automatically learn more representative features of welding statuses from the raw signal features captured by the visible light photodiode and the reflected laser light photodiode without any manual operations. The maximum correntropy loss function is applied to improve the learning ability of the proposed SAE method. Furthermore, a genetic algorithm (GA) is applied to optimize the key parameters of the proposed SAE method. The proposed SAE is applied to the high-power disk laser welding experiments and shows better performance in welding status monitoring than the standard AE framework and the conventional SVM and BP method. Additional experiments with different welding parameters validate the effectiveness and robustness of our proposed SAE method.
- 1 March 2018
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 33 (15) , 1708-1713
Effect of energy input on microstructure and mechanical properties in EBSM Ti6Al4V
- 1 March 2018
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 33 (15) , 1708-1713
Effect of energy input on microstructure and mechanical properties in EBSM Ti6Al4V
- Top Cited Papers
- 1 March 2018
- Published by Elsevier in Materials & Design
- Vol. 141, 210-219
Meso-scale modeling of multiple-layer fabrication process in Selective Electron Beam Melting: Inter-layer/track voids formation
- 1 March 2018
- Published by Elsevier in Materials & Design
- Vol. 141, 210-219
Top Cited PapersMeso-scale modeling of multiple-layer fabrication process in Selective Electron Beam Melting: Inter-layer/track voids formation
- 1 October 2017
- Published by Elsevier in Applied Surface Science
- Vol. 419, 150-158
Mechanism of surface morphology in electron beam melting of Ti6Al4V based on computational flow patterns
- 1 October 2017
- Published by Elsevier in Applied Surface Science
- Vol. 419, 150-158
Mechanism of surface morphology in electron beam melting of Ti6Al4V based on computational flow patterns
- Top Cited Papers
- 1 August 2017
- Published by Elsevier in Acta Materialia
- Vol. 134, 324-333
Multi-physics modeling of single/multiple-track defect mechanisms in electron beam selective melting
- 1 August 2017
- Published by Elsevier in Acta Materialia
- Vol. 134, 324-333
Top Cited PapersMulti-physics modeling of single/multiple-track defect mechanisms in electron beam selective melting
- Top Cited Papers
- 1 August 2016
- Published by Elsevier in Acta Materialia
- Vol. 115, 403-412
Multi-scale modeling of electron beam melting of functionally graded materials
- 1 August 2016
- Published by Elsevier in Acta Materialia
- Vol. 115, 403-412
Top Cited PapersMulti-scale modeling of electron beam melting of functionally graded materials