Katarzyna Sindera
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Katarzyna Sindera has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Anna Gancarczyk
Institute of Chemical Engineering, Polish Academy of Sciences, Bałtycka 5, 44-100 Gliwice, Poland
13 shared publications - Marzena Iwaniszyn
Institute of Chemical Engineering, Polish Academy of Sciences, Bałtycka 5, 44-100 Gliwice, Poland
13 shared publications - Mateusz Korpyś
Institute of Chemical Engineering, Polish Academy of Sciences, Bałtycka 5, Gliwice 44-100, Poland
12 shared publications - Andrzej Kołodziej
Institute of Chemical Engineering, Polish Academy of Sciences, Bałtycka 5, 44-100 Gliwice, Poland
10 shared publications - Przemysław J. Jodłowski
Cracow University of Technology, Faculty of Chemical Engineering and Technology, Warszawska 24, PL-31-155, Kraków, Poland
7 shared publications - Mikołaj Suwak
Institute of Chemical Engineering, Polish Academy of Sciences, Bałtycka 5, 44-100 Gliwice, Poland
5 shared publications
Latest Publications
- Open Access
Modification of Short-Channel Structures Towards Heat Transfer Intensification: CFD Modeling
In this paper, we present the results of heat transfer studies on short-channel structured packing in chemical reactors. Heat transfer coefficients, streamlines, and fluid temperatures were determined using CFD (Computational Fluid Dynamics). CFD simulations were performed for three modified short-channel structures, in which the front of the walls was rounded to eliminate inlet vortices and the outlet was modified (in three versions) to minimize outlet vortices that disturb the fluid flow. CFD simulations for a classic short-channel structure with straight walls were also performed. The results proved that modified structures experienced significantly more intensive heat transport compared to classic structures. Among the tested modifications, the most promising was Modification 1, for which the Nusselt number increased from 65% to 15% depending on the structure length and the Reynolds number. Additionally, for all modifications considered, there was no inlet vortex, which significantly reduced the transport intensity in the classic structure. Further down the channel, the transport intensity was similar for all structures, including the classic structure. The smoothest flow at the outlet of the structure was observed for Modification 1.
Open AccessModification of Short-Channel Structures Towards Heat Transfer Intensification: CFD Modeling
In this paper, we present the results of heat transfer studies on short-channel structured packing in chemical reactors. Heat transfer coefficients, streamlines, and fluid temperatures were determined using CFD (Computational Fluid Dynamics). CFD simulations were performed for three modified short-channel structures, in which the front of the walls was rounded to eliminate inlet vortices and the outlet was modified (in three versions) to minimize outlet vortices that disturb the fluid flow. CFD simulations for a classic short-channel structure with straight walls were also performed. The results proved that modified structures experienced significantly more intensive heat transport compared to classic structures. Among the tested modifications, the most promising was Modification 1, for which the Nusselt number increased from 65% to 15% depending on the structure length and the Reynolds number. Additionally, for all modifications considered, there was no inlet vortex, which significantly reduced the transport intensity in the classic structure. Further down the channel, the transport intensity was similar for all structures, including the classic structure. The smoothest flow at the outlet of the structure was observed for Modification 1.
- Open Access
Thermodynamic Irreversibility of the Flow and Transfer Phenomena Within Streamlined Structures of the Catalytic Reactors
An analysis is presented of the irreversibility of flow and thermal phenomena in innovative streamlined structured packing of catalytic chemical reactors. The fundamental equations of irreversible thermodynamics defining entropy production as a result of flow friction and heat transport are formulated. The parameters describing the flow and heat transport in these equations are determined using the Computational Fluid Dynamics (CFD) methodology. Local entropy production due to flow friction and heat transport in the channel structure is plotted and compared with flow-temperature maps and relations for flow resistance, pressure gradient, and Nusselt number derived from CFD. The calculations were performed for three gas velocities: 0.3; 2.0, and 6.0 ms−1. It was found that the entropy due to flow friction increases strongly with increasing gas velocity, while the entropy due to heat transport decreases with gas velocity, but to a limited extent. These opposing tendencies mean that there is always a minimum of the total entropy production (including these due to flow friction and heat transport), usually for moderate gas velocity. This minimum constitutes the optimum operating point of the reactor from the thermodynamic point of view.
Open AccessThermodynamic Irreversibility of the Flow and Transfer Phenomena Within Streamlined Structures of the Catalytic Reactors
An analysis is presented of the irreversibility of flow and thermal phenomena in innovative streamlined structured packing of catalytic chemical reactors. The fundamental equations of irreversible thermodynamics defining entropy production as a result of flow friction and heat transport are formulated. The parameters describing the flow and heat transport in these equations are determined using the Computational Fluid Dynamics (CFD) methodology. Local entropy production due to flow friction and heat transport in the channel structure is plotted and compared with flow-temperature maps and relations for flow resistance, pressure gradient, and Nusselt number derived from CFD. The calculations were performed for three gas velocities: 0.3; 2.0, and 6.0 ms−1. It was found that the entropy due to flow friction increases strongly with increasing gas velocity, while the entropy due to heat transport decreases with gas velocity, but to a limited extent. These opposing tendencies mean that there is always a minimum of the total entropy production (including these due to flow friction and heat transport), usually for moderate gas velocity. This minimum constitutes the optimum operating point of the reactor from the thermodynamic point of view.
- Open Access
Innovative Fixed-Bed Reactor Integrated with Heat Transfer System for Lean Methane Mixture Removal
A new type of compact, portable fixed-bed reactor integrated with a heat transfer system was developed for the removal of volatile and flammable air pollutants such as lean methane and volatile organic compounds (VOCs). The reactor may operate in catalytic or thermal combustion conditions with the purpose of achieving autothermal processes with the possibility of energy recovery. An excess heat recovery point was designed behind the reactor bed at the place where the gas temperature is the highest to enable its usage. The mathematical model is presented together with a number of simulation calculations performed for the assessment of the developed reactor. The case study in this paper was for catalytic methane oxidation at a temperature of 400 °C, a methane concentration between 0.1% and 2% by weight, a gas flow rate of 1 m3/s STP, and a heat exchange surface for the assumed plate exchanger from 10 to 200 m2. The calculations show that the thickness of the insulation is of little importance for the operation of the equipment, and a sufficient thickness was about 20–50 mm. The optimal area for the considered case is 80–100 m2. It was found that recovery of thermal energy is possible only for higher methane concentrations, above 0.3% by weight. Using an appropriate surface for the exchanger, it is possible to recover even 50% of the combustion enthalpy at a methane concentration of 0.45% by weight. For an exchanger area below 50 m2, the recoverable energy drops rapidly. It was found that the exchanger area is the most important equipment parameter under consideration.
Open AccessInnovative Fixed-Bed Reactor Integrated with Heat Transfer System for Lean Methane Mixture Removal
A new type of compact, portable fixed-bed reactor integrated with a heat transfer system was developed for the removal of volatile and flammable air pollutants such as lean methane and volatile organic compounds (VOCs). The reactor may operate in catalytic or thermal combustion conditions with the purpose of achieving autothermal processes with the possibility of energy recovery. An excess heat recovery point was designed behind the reactor bed at the place where the gas temperature is the highest to enable its usage. The mathematical model is presented together with a number of simulation calculations performed for the assessment of the developed reactor. The case study in this paper was for catalytic methane oxidation at a temperature of 400 °C, a methane concentration between 0.1% and 2% by weight, a gas flow rate of 1 m3/s STP, and a heat exchange surface for the assumed plate exchanger from 10 to 200 m2. The calculations show that the thickness of the insulation is of little importance for the operation of the equipment, and a sufficient thickness was about 20–50 mm. The optimal area for the considered case is 80–100 m2. It was found that recovery of thermal energy is possible only for higher methane concentrations, above 0.3% by weight. Using an appropriate surface for the exchanger, it is possible to recover even 50% of the combustion enthalpy at a methane concentration of 0.45% by weight. For an exchanger area below 50 m2, the recoverable energy drops rapidly. It was found that the exchanger area is the most important equipment parameter under consideration.
- 25 September 2023
- Published by Polish Academy of Sciences Chancellery in Chemical and Process Engineering: New Frontiers
- Vol. 44 (3) , 31
Innovative catalytic streamlined carriers with triangular channels
The paper presents research on a novel catalytic carrier, called "streamlined structure". The carrier is a short-channel monolith, whose walls are shaped like an airfoil profile (airplane wing). The intention is heat transfer intensification coupled with moderate flow resistance. Streamlined structures with triangular channel cross-section, 3mm, 6mm and 12 mm long, were designed and manufactured using the SLM (Selective Laser Melting) technique for the experimental verification. The structures were modelled using the CFD (Computational Fluid Dynamics) software to derive flow resistance, flow patterns and heat transfer coefficients. Compared to classic structures, CFD showed intensified heat transfer, combined with acceptable flow resistance increase. CFD proved the lack of an inlet vortex, which in classical structures seriously reduces the intensity of heat transfer. The CFD has been satisfactorily verified by experiments.
- 25 September 2023
- Published by Polish Academy of Sciences Chancellery in Chemical and Process Engineering: New Frontiers
- Vol. 44 (3) , 31
Innovative catalytic streamlined carriers with triangular channels
The paper presents research on a novel catalytic carrier, called "streamlined structure". The carrier is a short-channel monolith, whose walls are shaped like an airfoil profile (airplane wing). The intention is heat transfer intensification coupled with moderate flow resistance. Streamlined structures with triangular channel cross-section, 3mm, 6mm and 12 mm long, were designed and manufactured using the SLM (Selective Laser Melting) technique for the experimental verification. The structures were modelled using the CFD (Computational Fluid Dynamics) software to derive flow resistance, flow patterns and heat transfer coefficients. Compared to classic structures, CFD showed intensified heat transfer, combined with acceptable flow resistance increase. CFD proved the lack of an inlet vortex, which in classical structures seriously reduces the intensity of heat transfer. The CFD has been satisfactorily verified by experiments.
- 25 September 2023
- Published by Polish Academy of Sciences Chancellery in Chemical and Process Engineering: New Frontiers
- Vol. 44 (3) , 27
Simplified modelling of a fixed bed reactor for catalytic methane combustion
The work concerned the introduction of simplifications in a one-dimensional mathematical model of a chemical reactor. Fecralloy foam with a pore density of 16 PPC (pores per centimetre) was used as catalyst support. The analysed process was the combustion of methane with a typical concentration found in the ventilation air of hard coal mines. The process was carried out using a palladium catalyst.
- 25 September 2023
- Published by Polish Academy of Sciences Chancellery in Chemical and Process Engineering: New Frontiers
- Vol. 44 (3) , 27
Simplified modelling of a fixed bed reactor for catalytic methane combustion
The work concerned the introduction of simplifications in a one-dimensional mathematical model of a chemical reactor. Fecralloy foam with a pore density of 16 PPC (pores per centimetre) was used as catalyst support. The analysed process was the combustion of methane with a typical concentration found in the ventilation air of hard coal mines. The process was carried out using a palladium catalyst.
- Open Access
Characterization of Fluid Flow and Heat Transfer of Expanded Metal Meshes for Catalytic Processes
In this work, three raised expanded metal meshes (EMMs) differing in mesh size were tested experimentally with regard to their flow and transport properties. Empirical equations for the Nusselt number and Fanning friction factor were developed. Alongside the experiments, simple computational fluid dynamics (CFD) models were used to simulate the pressure drop and heat transfer coefficients within EMMs. Finally, the Performance Efficiency Criterion (PEC) was applied to compare EMMs with other reactor packings.
Open AccessCharacterization of Fluid Flow and Heat Transfer of Expanded Metal Meshes for Catalytic Processes
In this work, three raised expanded metal meshes (EMMs) differing in mesh size were tested experimentally with regard to their flow and transport properties. Empirical equations for the Nusselt number and Fanning friction factor were developed. Alongside the experiments, simple computational fluid dynamics (CFD) models were used to simulate the pressure drop and heat transfer coefficients within EMMs. Finally, the Performance Efficiency Criterion (PEC) was applied to compare EMMs with other reactor packings.
- Open Access
Momentum Transfer in Short-Channel Structures of Hexagonal Channel Cross-Section Shape: Experiments vs. CFD
Short-channel structures are promising catalyst carriers because it is easy to control the heat/mass transfer and fluid flow characteristics by changing their lengths. In this work, the flow resistance of hexagonal structures was investigated experimentally and numerically. The structure tested (6 mm long) was manufactured from AISI 316 steel using the selective laser melting technique. Due to some differences between theoretical approaches and practical results, two types of computational models were applied to analyze the pressure distribution in a short hexagonal duct. It was shown that although experimental results agree with some theoretical solutions, the channel wall thickness should not be omitted from the overall flow resistance. A comparison of short structures differing in channel length with widely used long monoliths was performed as well.
Open AccessMomentum Transfer in Short-Channel Structures of Hexagonal Channel Cross-Section Shape: Experiments vs. CFD
Short-channel structures are promising catalyst carriers because it is easy to control the heat/mass transfer and fluid flow characteristics by changing their lengths. In this work, the flow resistance of hexagonal structures was investigated experimentally and numerically. The structure tested (6 mm long) was manufactured from AISI 316 steel using the selective laser melting technique. Due to some differences between theoretical approaches and practical results, two types of computational models were applied to analyze the pressure distribution in a short hexagonal duct. It was shown that although experimental results agree with some theoretical solutions, the channel wall thickness should not be omitted from the overall flow resistance. A comparison of short structures differing in channel length with widely used long monoliths was performed as well.
- 1 February 2021
- Published by Elsevier in Chemical Engineering Journal
- Vol. 405
Entrance effects on forced convective heat transfer in laminar flow through short hexagonal channels: Experimental and CFD study
- 1 February 2021
- Published by Elsevier in Chemical Engineering Journal
- Vol. 405
Entrance effects on forced convective heat transfer in laminar flow through short hexagonal channels: Experimental and CFD study